light LAND ROVER DISCOVERY 1995 Owners Manual

ELECTRICAL
1
DESCRIPTION AND OPERATION ELECTRICAL EQUIPMENT
DESCRIPTION
The electrical system is Negative ground, and it is
most important to ensure correct polarity of the
electrical connections at all times. Any incorrect
connections made when reconnecting cables may
cause irreparable damage to the semi-conductor
devices used in the generator and regulator. Incorrect
polarity would also seriously damage any
transistorized equipment such as radio and
tachometer etc.
WARNING: During battery removal or
before carrying out any repairs or
maintenance to electrical components
always disconnect the battery negative lead first.
If the positive lead is disconnected with the
negative lead in place, accidental contact of the
wrench to any grounded metal part could cause a
severe spark, possibly resulting in personal
injury. Upon installation of the battery the positive
lead should be connected first.
GENERATOR
The generator is a three phase, field sensed unit. The
rotor and stator windings produce three phase
alternating current, AC, which is rectified to direct
current, DC. The electronic voltage regulator unit
controls the generator output voltage by high
frequency switching of the rotor field circuit. Use only
the correct Vehicle replacement fan belt. Occasionally
check that the engine and generator pulleys are
accurately aligned.
It is essential that good electrical connections are
maintained at all times. Of particular importance are
those in the charging circuit (including those at the
battery) which should be occasionally inspected to
see that they are clean and tight. In this way any
significant increase in circuit resistance can be
prevented.Do not disconnect battery cables while the engine is
running or damage to the semi-conductor devices
may occur. It is also inadvisable to break or make any
connections in the generator charging and control
circuits while the engine is running.
The electronic voltage regulator employs micro-circuit
techniques resulting in improved performance under
difficult service conditions. The whole assembly is
encapsulated in silicone rubber and housed in an
aluminium heat sink, ensuring complete protection
against the adverse effects of temperature, dust, and
moisture etc.
The regulating voltage is set during manufacture to
give the required regulating voltage range of 14.2±
0.2 volts, and no adjustment is necessary. The only
maintenance needed is the occasional check on
terminal connections and wiping with a clean dry
cloth.
The generator system provides for direct connection
of a charge (ignition) indicator warning light, and
eliminates the need for a field switching relay or
warning light control unit. As the warning lamp is
connected in the charging circuit, lamp failure will
cause loss of charge. Lamp should be checked
regularly and spare carried.
When using rapid charge equipment to re-charge the
battery, the battery must be disconnected from the
vehicle.
NOTE: For description and operation of
electrical circuits see separate publication:
Electrical Troubleshooting Manual.

86ELECTRICAL
2
DESCRIPTION AND OPERATION ANTI-THEFT SYSTEM FUNCTION
Perimetric protection
Using the key in the correct sequence will turn on and
off perimetric protection only. When fully perimetrically
armed, all doors, and bonnet [hood] are protected
against unauthorised access. If the door key is used in
the normal manner the driver will be unaware of the
door key sequence. The time taken to lock or unlock
with the key must be less than 5 seconds. To prevent
unauthorised tampering, the alarm will sound if the
key is held in the unlocked position for longer than 5
seconds when armed. Cranking is disabled when
perimetric protection is armed.
NOTE: When key is turned left or right the
keyswitch input will be activated, in
conjunction with the sill button switch
when links are operated.
Volumetric protection
Using the handset transmitter will turn on and off
volumetric protection. In volumetric mode the vehicle
interior is protected using the ultrasonic sensor. Using
the handset also arms and disarms the vehicle
perimetrically. Cranking is disabled when volumetric
and perimetric protection is armed.
NOTE: If armed volumetrically the vehicle
CANNOT be disarmed using the key.
Alarm horn
When an intrusion is detected the alarm horn will
sound intermittently (Switzerland and Denmark
continuous horn sound) and the hazard lights flash
(where territorial regulations allow) for 30 seconds.
The alarm must be retriggered before alarm horn will
sound again.Vehicle status indication
Vehicle status is indicated by up to three devices: (a)
alarm horn, (b) hazard lights, (c) dash board LED.
When the vehicle arms in either mode the hazard
lights will flash three times and the LED will flash
rapidly for 10 seconds. LED will then flash at a slower
rate while vehicle is armed. When the vehicle disarms,
hazard lights will flash once and LED will extinguish. If
LED remains lit, it indicates that the alarm has been
triggered. Turning on ignition or arming the alarm will
extinguish LED. The LED will give a long pulse flash
to indicate the ultrasonic unit being activated.
Central locking
Central locking is controlled by the alarm ECU and
may be operated by the key, sill button(s) or handset.
The system works on both front doors on four door
vehicles or driver's door on two door vehicles.
NOTE: The central door locking system
will shut down for a short period after
more than 15 consecutive operations.
Inertia switch
An inertia switch is incorporated in the alarm system
ECU. If ignition is on and the vehicle receives an
impact sufficient to activate the inertia switch, the ECU
will signal to unlock central locking actuators and flash
hazard lights. Central locking will remain disabled for
30 seconds. To reset turn ignition off and then on after
the 30 second period has elapsed.
Ultrasonic unit
The unit operates by emitting an air pressure carrier
wave and receiving the wave back. Any disturbance
within the vehicle which disturbs the wave will be
detected, triggering the alarm.
When the volumetric sensor is activated it monitors
movement within the vehicle for 15 seconds before
detecting and responding to intrusions. If the sensor
detects movement within the vehicle it delays arming
until a 15 seconds quiet period has elapsed. If
continuous movement is detected the alarm will not
arm volumetrically.

ELECTRICAL
3
DESCRIPTION AND OPERATION Radio frequency system
The RF system uses four frequencies according to
market. If the coaxial aerial is not fitted system
performance will be impaired. Both ECU and handset
have a colour coded label.
Frequency Colour Territory
ECU/Handset
433.92 MHz Blue/black........................... UK, Ireland........................
224.5 MHz, Yellow/yellow............................ France...................
433.92 MHz Blue/Purple........................... Germany......................
433.92 MHz Blue/blue........................... Europe, not France, Switzerland, Italy, Denmark,..........................
Germany
433.92 MHz White/Blue........................... Switzerland, Denmark.......................
315.0 MHz Green/green............................. Rest of world, Italy, Australia....................
315.0 MHz Orange/Green............................. Gulf, Japan..................
Partially armed mode
If a door, tailgate or bonnet [hood] is left open when
the system is armed, the LED will not light for 10
seconds indicating a mislock condition. Hazard lights
will not flash. If an open door or tailgate is causing the
mislock, the starter motor is disabled. The alarm will
sound if ignition is turned to start position. If an open
bonnet [hood] is causing the mislock the starter motor
is disabled. The alarm will arm the volumetric part of
the system. If the door tailgate or bonnet [hood] is
subsequently closed, after a 5 second delay, the
doors will unlock and immediately lock and the system
will fully arm.
Handset transmitter
The handset LED will give one short flash when
button is pressed momentarily.
If button is held down the LED will light again after 2
seconds for 2 seconds, and extinguish until button is
released and repressed. The handset contains unique
information distinguishing it from other transmitters. It
also contains a set of 'random' rolling codes
programmed into the ECU before leaving the factory.
Each time the handset is pressed a different code is
transmitted to the ECU.
If handset is operated more than four times outside
the vehicle range (6 metres) or power supply is
removed, it will be necessary to re-sychronise handset
and the ECU by pressing the handset three times
within range and within 5 seconds.
NOTE: If both handsets are lost or
damaged when system is armed it will be
necessary to fit a new ECU with two
matching handsets.
Handset batteries
If handset LED flashes continuously when button is
pressed, the batteries need replacing. The hazard
lights will flash one 3 second pulse, instead of three
times upon arming vehicle.
Power up mode
The alarm system always remembers the state it was
left in when power was removed. If the alarm powers
up in an armed state and is subsequently triggered it
will give a warning that it will fully trigger unless
disarmed. This warning consists of short horn pulses
every two seconds for 15 seconds.
New born mode
When the ECU is first produced, it will be in its 'new
born' mode. In this mode it will respond to any remote
of the right frequency. This mode will be cancelled
when the ECU has received ten valid handset signals
without power interruption.
Engine cranking
It is only possible to crank the engine when ignition is
ON and alarm disabled.

86ELECTRICAL
4
DESCRIPTION AND OPERATION BUILT IN TEST PROCEDURE
The built in test procedure is accessed as follows:
1.Starting conditions: ignition off, doors unlocked,
bonnet [hood] switch depressed.
2.Carry out instructions 3 to 7 within 8 seconds.
3.Release bonnet [hood] switch.
4.Switch ignition ON.
5.Lock doors.
6.Switch ignition OFF.
7.Switch ignition ON.
If alarm is correctly accessed, horn will sound and
LED will flash. The following checks can be made:
8.Open and close any door or tailgate - LED will
light.
9.Depress bonnet [hood] switch - hazards will
flash.
10.Check engine cranking is disabled. Do not turn
off ignition.
11.Check ultrasonic by operating handset, LED will
emit one 5 second flash, and will flash if interior
is disturbed.
NOTE: If ECU is new born mode any
handset of the right frequency will work. If
not an initialised handset is required see
Handset Initialisation.
12.Turn OFF ignition or press handset to end test
procedure. Horn will sound as before to indicate
end of test mode.

ELECTRICAL
5
DESCRIPTION AND OPERATION ANTI THEFT ALARM SYSTEM
The main function of the system is to offer easy to use
remote locking and unlocking of the vehicle without
having to actively select the alarm function.
ALARM COMPONENTS
COMPONENT LOCATION
1. Electronic control unit (ECU) and relays Passenger footwell.................
2. Bonnet switch RH engine bay..........................................................
3. Door switches
4. Alarm sounder RH engine bay.........................................................
5. Light emitting diode (LED) Dash panel.......................................
6. Ultrasonic unit Roof map pocket.........................................................
7. Lock barrel, sill buttons
8. Handset transmitter
9. Aerial 'A' post, passenger side........................................................................

86ELECTRICAL
6
DESCRIPTION AND OPERATION ALARM COMPONENT LOCATIONS (96 MODELS)
COMPONENT LOCATION
1. Electronic control unit (ECU) and relays Under dash (passenger side).................
2. Anti-theft alarm indicator light Instrument panel..................................
3. Engine immobilisation warning light (EIWL) * Instrument panel..........
4. Passive coil Over starter switch barrel.............................................................
5. Bonnet switch RH engine compartment..........................................................
6. Door switches
7. Ultrasonic sensor Interior light switch panel....................................................
8. Lock barrel, sill buttons
9. Handset and key
10. Battery backed-up sounder or horn * RH engine compartment......................
11. Immobilisation unit (spider) * Above heater...................................
12. Aerial Part of fascia harness.......................................................................
* where applicable

86ELECTRICAL
8
DESCRIPTION AND OPERATION DETECTION COMPONENTS
Switches
Perimetric protection for the vehicle is provided by
ECU inputs connected to the following:
Key switches (including starter)
Sill buttons
Bonnet switch
Door switches
Ultrasonic sensor
The ultrasonic sensor is located on the interior light
switch panel and triggers the alarm if movement is
detected.
WARNING INDICATORS
Battery backed-up sounder
The battery backed-up sounder is located in the
engine compartment and provides an audible warning
whenever the alarm is triggered.
NOTE: Disconnecting the vehicle battery
will result in the alarm sounding if the
correct procedure has not been followed.
See Repair, Battery.
Engine immobilisation warning light (EIWL)
The engine immobilisation warning light is located in
the instrument pack and provides a visual indication
that the engine is immobilised.
Anti-theft alarm indicator light
The anti-theft alarm indicator light is located in the
instrument pack and provides a visual indication of the
alarm status.
Inertia switch and central door locking
As a safety feature, the alarm system is designed to
recognise the inertia switch and via the ECU, unlock
the doors in the event of a collision.
NOTE: This feature only applies when the
starter switch is in the on position.ANTI-THEFT ALARM OPERATION (96 MODELS)
Full arming and immobilisation
Locking the vehicle using the handset immobilises the
engine and initializes both volumetric and perimetric
protection, providing:
1.After a lock signal has been received, a period of
15 seconds has elapsed during which no
movement is detected inside the vehicle;
2.No door or bonnet is open.
NOTE: If either of the above conditions are
not satisfied, the alarm will only be
partially armed. This is a mislock condition
which will be made apparent by a delay of 10
seconds before the anti-theft alarm indicator
begins to flash.
Disarming the alarm
NOTE: ALWAYS disarm the alarm using
the handset.
Unlocking with the key will not disarm the alarm or
mobilise the vehicle. If the handset fails to unlock the
vehicle
See Repair, Handset.
Partial arming and immobilisation
The alarm will be partially armed and the engine
immobilised if the vehicle is locked with the handset or
key, if:
1.After a lock signal has been received, a period of
15 seconds has elapsed during which movement
is detected inside the vehicle;
2.A door or bonnet is open.
NOTE: This is a mislock condition which
will be made apparent by a delay of 10
seconds before the anti-theft alarm
indicator begins to flash. Subsequent closure of
the offending aperture will cause the alarm to
attempt full arming as previously described.
Immobilisation
The vehicle will be automatically immobilised
whenever any of the following conditions occur:
1.The vehicle is locked using the handset.
2.The vehicle is locked using the key.
3.Thirty seconds after the starter switch has been
turned off AND the driver's door opened.
4.Five minutes after the starter switch is turned off
or the alarm disarmed.

ELECTRICAL
9
DESCRIPTION AND OPERATION Mobilisation
The vehicle can be mobilised using any one of the
following processes:
1.Placing the handset in close proximity to the
starter switch with the starter switch turned on
(normally achieved by placing the key in the
starter switch, providing the key and handset are
attached).
NOTE: Under normal circumstances the
remobilisation of the vehicle will not be
apparent.
2.Pressing unlock button on handset.
3.Pressing lock button on handset with starter
switch turned on.
4.Entry of EKA code using the key.
NOTE: Any attempt to start the vehicle
using the key (detached from the handset)
will be unsuccessful. Use one of the above
methods.
See Warning indicators.
Volumetric protection
When the vehicle is locked using the handset both
perimetric and volumetric protection are activated
providing there is no mislock condition.
Perimetric protection
The vehicle is always perimetrically protected when
the alarm is armed using the handset. Perimetric
protection only, can be achieved if the vehicle is
locked using the key.
NOTE: The handset should ALWAYS be
used for unlocking the vehicle. If the
handset fails to unlock the vehicle
See
Repair, Handset.
Battery backed-up sounder (BBUS)
The sounder provides audible indication of alarm
status including:
Anti-theft warnings;
Confirmation of access to built-in test.
NOTE: Disconnecting the vehicle battery
will result in the alarm sounding if the
correct procedure has not been followed.
See Repair, Battery.
Alarm horn
The horn provides audible indication (as BBUS) of
alarm status.
NOTE: Disconnecting the vehicle battery
will have no effect on the horn.
Engine immobilisation warning light (EIWL)
NOTE: Under normal circumstances the
light will not illuminate.
The light will only illuminate (after 2 seconds) if the
handset is detached from the key (or the handset
fails) and an attempt is made to start the vehicle.
Anti-theft alarm indicator light
The light flashes to indicate the alarm status.
If the alarm system is fully armed, the light will flash
rapidly for 10 seconds and then settle to the slow
(anti-theft deterrent) flash.
If the alarm system is perimetrically armed, the light
will intermittently flash rapidly for 10 seconds and then
settle to the slow (anti-theft deterrent) flash.
If the alarm system is partially armed, the light will
NOT emit the slow flash until 10 seconds after arming
(to allow the cause to be investigated).
If the vehicle has been left unlocked, providing the
driver's door is closed, the light will flash slowly
indicating immobilisation. If the driver's door is open,
the light will remain illuminated.
Emergency key access (EKA)
The emergency key access code should be entered in
accordance with the instructions in the Owner's
Handbook.

ELECTRICAL
11
DESCRIPTION AND OPERATION ANTI-THEFT ALARM BUILT-IN TEST (96 MODELS)
NOTE: The handset should be detached
from the key to allow perimetric testing of
the alarm system. The system will
automatically switch to volumetric testing if the
handset is in close proximity to the starter switch.
The built-in test procedure can be accessed providing
the following conditions exist:
Alarm disarmed.
Ignition off.
Doors unlocked.
Bonnet[hood] closed.
The test mode can be entered by completing the
following instructions within 5 seconds:
1.Open bonnet.
2.Turn starter switch on.
3.Open driver's door (far enough to activate
switch).
4.Turn starter switch off.
5.Turn starter switch on.
If the test mode has been correctly accessed, the
sounder/horn will operate briefly and the anti-theft
alarm indicator and hazard warning lights will flash.
Perimetric tests
The anti-theft alarm indicator light and the hazard
warning lights will flash when:
1.Door switches are activated;
2.The bonnet is opened;
3.Sill switches are activated;
4.Key switches are activated.
NOTE: Operation of key switches can be
verified by turning the key in the relevent
direction so as not to simultaneously
activate the sill switch. If the key switch changes
state, the change should be detected but the sill
switch will not be activated.
Volumetric tests
Press the unlock button or move the handset close to
the starter switch to disable perimetric testing and
enable volumetric testing. If movement is detected
within the vehicle by the ultrasonic sensor it will be
indicated by flashing the anti-theft alarm indicator and
hazard warning lights.
NOTE: Exit anti-theft alarm built-in test by
turning starter switch to the off position.

ELECTRICAL
1
ADJUSTMENT IGNITION TIMING
Service repair no - 86.35.15
Adjust
1.It is essential that following procedures are
adhered to. Inaccurate timing can lead to serious
engine damage and additionally create failure to
comply with emission regulations. If timing is
being checked in vehicle, air conditioning
compressor must be disengaged.
2.On initial engine build, or if distributor has been
disturbed for any reason, ignition timing must be
set statically to 6°B.T.D.C.
NOTE: This approximate setting is made
only to ensure that engine may be started.
CAUTION: On no account must engine be
started before this operation is carried out.Equipment required :-
Calibrated Tachometer
Stroboscopic lamp
3.Couple stroboscopic timing lamp and tachometer
to engine following manufacturer's instructions.
4.Disconnect vacuum hose from distributor.
5.Start engine. With no load, and without
exceeding 3,000 rev/min run engine until normal
operating temperature is reached. (Thermostat
open). Check that engine idles within tolerance
specified in data section.
6.Idle speed for timing purposes must not exceed
800 rev/min.
7.Run engine at idle speed and check timing using
stroboscope light on timing marker and pointer.
WARNING: Keep hands and equipment
away from belt.
8.If timing is not as specified, switch off engine.
Loosen distributor clamp bolt and turn distributor
to advance or retard ignition as necessary.
Tighten clamp bolt, start engine and recheck
timing.
WARNING: Personal injury may result if an
attempt is made to adjust distributor whilst
engine is running.
9.Upon completion, switch off engine and retighten
distributor clamping bolt securely. Recheck
timing, to ensure retightening has not disturbed
distributor position.
10.Refit vacuum hose.
11.Disconnect stroboscopic timing lamp and
tachometer from engine.