engine LAND ROVER DISCOVERY 1995 Workshop Manual

MFI
3
FAULT DIAGNOSIS FUEL PRESSURE CHECK
In order to check the fuel pressure it is necessary to
first depressurise the fuel system as follows:
WARNING: Under normal operating
conditions the multiport fuel injection
system is pressurised by a high pressure
fuel pump, operating at up to 2.3 to 2.5 bar. When
engine is stationary pressure is maintained within
system. To prevent pressurised fuel escaping and
to avoid personal injury it is necessary to
depressurise multiport fuel injection system
before any service operations are carried out.
If vehicle has not been run there will be a small
amount of residual pressure in fuel line. The
depressurising procedure must still be carried out
before disconnecting any component within the
fuel system.
The spilling of fuel is unavoidable during this
operation. Ensure that all necessary precautions
are taken to prevent fire and explosion.
A Pressure gauge 18G1500
B Fuel tank and pump
C Fuel filter
D Fuel injectors x 8
E Regulator1.Remove fuel pump relay module.
See Repair,
Multiport Fuel Injection Relay
2.Start and run engine.
3.When sufficient fuel has been used to cause fuel
line pressure to drop, injectors will become
inoperative, resulting in engine stall. Switch off
ignition.
4.Disconnect battery negative lead. .
NOTE: Fuel at low pressure will remain in
system. To remove low pressure fuel,
place absorbent cloth around fuel pipe at
the filter during disconnection.
5.Connect the pressure gauge on the outlet from
the filter, located on the chassis under the right
rear wheel arch.
6.Reconnect the battery and turn the ignition to
position II while observing the pressure gauge.
Results
Expected reading 2,39-2,672 kgf/cm
2
Pressure drop-max 0.7 kgf/cm2in one minute.
If pressure is low check that filter is not blocked
and pump is operating satisfactorily. Then
recheck pressure. If pressure is still low renew
regulator.
See Repair, Fuel Pressure
Regulator

19FUEL SYSTEM
2
REPAIR AIR FLOW SENSOR
Service repair no - 19.22.25
Remove
NOTE: The air flow sensor is not a
serviceable item. In event of failure or
damage the complete unit must be
replaced.
1.Disconnect battery negative lead.
2.Release intake hose clamp, disconnect from
sensor.
3.Disconnect multi-plug.
4.Release two clips securing air cleaner to air flow
sensor. Remove sensor from engine
compartment.
Refit
5.Reverse removal procedure. Ensure multi-plug is
firmly reconnected, and hose clamp at the rear
of sensor is securely tightened, to prevent
unmetered air entering engine.THROTTLE POSITION SENSOR
Service repair no - 19.22.49
Remove
1.Disconnect battery negative lead.
2.Disconnect multi-plug from harness.
3.Remove two screws securing sensor to plenum
chamber and carefully pull sensor off throttle
shaft.
4.Remove old gasket.
Refit
5.Fit new gasket.
6.Align sensor and shaft flats, slide sensor on to
throttle shaft. Secure sensor to plenum chamber.
CAUTION: DO NOT operate throttle
mechanism while throttle position sensor
is loosely fitted, damage may be caused to
throttle position sensor wiper track.

19FUEL SYSTEM
4
REPAIR MULTIPORT FUEL INJECTION RELAYS
Service repair no - 19.22.08
The two Multiport fuel injection relays are located in
the RH footwell area behind the 'A' post trim panel.
The fuel injection relays can be identified as follows:
A. Fuel pump relay - Blue base
B. Main relay - Black base
Remove
1.Release front door seal from 'A' post.
2.Remove lower 'A' post trim panel.
3.Pull relay from base.
Refit
4.Reverse removal procedure.ENGINE CONTROL MODULE (ECM)-14 CUX
Service repair no - 19.22.34
NOTE: The ECM is not serviceable, in
event of unit failure it must be replaced.
Remove
1.Remove the fascia right-hand closing panel.
2.Remove the right-hand footwell side panel trim.
3.Disconnect battery negative lead.
4.Release ECM plug retaining clip.
5.Maneouvre the front of the plug (in the direction
of the bold arrow) and detach the other end of
the plug from the retaining peg.
6.Release the two screws securing the ECM to the
right-hand footwell side panel.
7.Withdraw the ECM from the clip.
Refit
8.Refit the ECM securely in the clip and fit the two
screws.
9.Reconnect the ECM harness plug. Ensure that
the plug is pushed firmly into its location and that
the retaining clip secures the plug in position.
10.Reverse removal procedure.

MFI
5
REPAIR INERTIA FUEL SHUTOFF SWITCH
Service repair no - 18.30.35
The inertia fuel shutoff switch is located on the
bulkhead next to the washer reservoir under bonnet
[hood].
Remove
1.Disconnect battery negative lead.
2.Disconnect multiplug from inertia switch.
3.Remove 2 screws securing inertia switch to
mounting bracket.
4.Remove inertia switch.
Refit
5.Position inertia switch to mounting bracket and
secure with screws.
6.Connect multiplug to inertia switch.
7.Reconnect battery negative lead.ENGINE FUEL TEMPERATURE SENSOR
Service repair no - 19.22.08
Remove
NOTE: Fuel leakage will not occur when
sensor is removed from fuel rail, therefore
it is not necessary to depressurise the fuel
system.
1.Disconnect battery negative lead.
2.Disconnect multi-plug from sensor.
3.Release sensor from fuel feed rail.
Refit
4.Reverse removal procedure. Ensure sensor is
tightened securely in fuel rail.

19FUEL SYSTEM
6
REPAIR ENGINE COOLANT TEMPERATURE SENSOR
Service repair no - 19.22.18
Remove
1.Position drain tray to collect coolant spillage.
2.Disconnect multiplug from coolant sensor.
3.Remove sensor from thermostat housing.
4.Remove and discard copper washer.
Refit
5.Fit a new copper washer.
6.Fit sensor and tigten securely.
7.Top-up cooling system.
8.Run engine, check for water leaks around
sensor.DEPRESSURISING FUEL SYSTEM
WARNING: Under normal operating
conditions the Multiport fuel injection
system is pressurised by a high pressure
fuel pump, operating at up to 2.3 to 2.5 bar When
engine is stationary pressure is maintained within
system. To prevent pressurised fuel escaping and
to avoid personal injury it is necessary to
depressurise multiport fuel injection system
before any service operations are carried out.
If vehicle has not been run there will be a small
amount of residual pressure in fuel line. The
depressurising procedure must still be carried out
before disconnecting any component within the
fuel system.
The spilling of fuel is unavoidable during this
operation. Ensure that all necessary precautions
are taken to prevent fire and explosion.
1.Remove fuel pump relay module.
See
Multiport Fuel Injection Relays
2.Start and run engine.
3.When sufficient fuel has been used to cause fuel
line pressure to drop, injectors will become
inoperative, resulting in engine stall. Switch off
ignition.
4.Disconnect battery negative lead.
NOTE: Fuel at low pressure will remain in
system. To remove low pressure fuel,
place absorbent cloth around fuel feed
hose at fuel rail.
5.Disconnect either:
a) Nut and olive at fuel rail
OR
b) Hose at inlet end of fuel filter.
Refit
6.Refit fuel feed hose.
7.Refit fuel pump relay module, reconnect battery.
8.Crank engine (engine will fire in approximately 6
to 8 seconds).

19FUEL SYSTEM
16
REPAIR Refit
1.Clean mating faces of cylinder heads, cylinder
block and intake manifold.
2.Locate NEW seals in position with ends
engaged in notches formed between the cylinder
heads and block.
3.Apply RTV sealant between ends of seals,
cylinder head and block.
4.Fit intake manifold gasket with the word
'FRONT'to the front and open bolts hole to the
front RH side.
5.Fit gasket clamps and tighten bolts finger tight.
6.Locate intake manifold onto cylinder heads,
clean threads of manifold securing bolts.
7.Allow 10 minutes for RTV sealant to cure.
8.Fit manifold bolts finger tight. Working in the
sequence shown tighten the bolts to
38 Nm.
9.Tighten the gasket clamp bolts to18 Nm.
10.Reverse removal procedure.
11.Fill cooling system.
See COOLING SYSTEM,
Repair, Radiator
12.Start engine check for water and fuel leaks.

MFI
17
REPAIR FUEL FILTER
Service repair no - 19.25.02
Remove
WARNING: Spilling of fuel is unavoidable
during this operation. Ensure all
necessary precautions are taken to
prevent fire and explosion.
WARNING: Ensure fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out following instructions.
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Access to filter is gained through right hand rear
wheel arch.
3.Clean area around hose connections to prevent
ingress of foreign matter into fuel system. Clamp
inlet and outlet hoses to prevent fuel spillage
when disconnecting hoses.
4.Loosen two fuel line unions and remove hoses.
Plug ends of hoses to prevent ingress of dirt.
5.Release securing bolt and bracket and remove
filter from chassis side member.
Refit
6.Fit a new filter observing direction of flow arrows
stamped on canister.
7.Tighten securing nut and bolt.
8.Fit inlet and outlet hoses. Tighten to
30Nm.
9.Refit fuel pump relay module, reconnect battery.
10.Start engine and inspect for fuel leaks around
hose connections.

MFI
19
REPAIR THROTTLE CABLE
Service repair no - 19.20.06
Remove
1.Remove clevis pin securing cable to lever.
2.Carefully pry throttle cable adjustment nut out of
mounting bracket.
3.Remove cable from mounting bracket.
4.Release outer cable from retaining clips in
engine compartment.
5.Remove lower dash panel.
6.Disconnect cable from accelerator pedal and
release cable locknut.
7.Feed cable through bulkhead grommet into
engine compartment.
Refit
8.Feed new cable from engine compartment
through bulkhead grommet.
9.Connect cable to accelerator pedal.
10.Connect cable to throttle linkage, using a new
cotter pin.
11.Clip outer cable adjustment nut into mounting
bracket.
12.Adjust outer cable to give 1.57 mm free play in
inner cable. Check throttle operation.

MFI
21
REPAIR 6.Remove access panel from floor.
7.Disconnect multi-plug from fuel sender unit.
8.Disconnect two fuel line unions from fuel pump.
9.Using service tool no. LRT-19-001, remove
pump unit retaining ring. Withdraw unit from fuel
tank.
WARNING: A quantity of fuel will be
retained in body of unit, care must be
taken to prevent fuel spillage when unit is
removed.
Refit
10.Insert fuel pump into tank. Fit retaining ring.
Tighten to
48 Nm.
11.Connect fuel lines to pump.
12.Connect multi-plug to sender unit.
13.After assembly, check all fuel pipes, sealing
rings and hose connections are secure.
14.Run engine to check for fuel leaks.
15.Inspect access panel seal, fit a new seal if
necessary.
16.Fit access panel and tighten screws.
17.Reverse removal procedure. 4 - 5. Fit insulation
and carpet.

MFI
23
REPAIR
13.Remove back two bolts and nut plates securing
fuel tank cradle.
14.Remove front nuts, bolts and washers. Remove
fuel tank cradle.
15.With assistance, tilt right hand side of tank
upwards and manoeuvre tank through chassis to
remove.
Refit
16.Reverse removal procedure. Ensuring sealing
ring, fuel pipe and hose connections are secure.
17.Run engine, check all connections for fuel leaks.