engine LAND ROVER DISCOVERY 1995 Workshop Manual

19FUEL SYSTEM
2
REPAIR THROTTLE CABLE
Service repair no - 19.20.06
Remove
1.Disconnect battery negative lead.
2.Remove pin and clevis pin securing throttle
cable to throttle lever.
3.Pull ferrule from abutment bracket and withdraw
throttle cable.
4.Release throttle cable from clip on bulkhead.
5.Remove pin and clevis pin securing throttle
cable to throttle lever.
6.Release grommet from bulkhead.
7.Withdraw throttle cable from engine
compartment.
Refit
8.Reverse removal procedure. Use new pins to
secure clevis pins.
9.Adjust throttle cable.
See Adjustment,
Throttle Cable
INTAKE HOSE TURBOCHARGER
Service repair no - 19.42.11
Remove
1.Disconnect battery negative lead.
2.Loosen clip and disconnect intake hose from
turbocharger.
3.Loosen clip and disconnect breather hose from
intake hose.
4.Remove clip and disconnect hose from air
cleaner, discard clip.
5.Remove intake hose
Refit
6.Reverse removal procedure. Use a new clip to
secure intake hose to air cleaner.

Tdi
3
REPAIR TURBOCHARGER OIL FEED PIPE
Service repair no - 19.42.14
Remove
1.Disconnect battery negative lead.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Manifold
and Exhaust System - Tdi
3.Remove banjo bolt securing oil feed pipe to
turbocharger, discard 2 sealing washers.
4.Unscrew union, disconnect oil feed pipe from
cylinder block.
CAUTION: Plug the connections.
5.Move oil feed pipe from behind turbocharger and
remove.
Refit
6.Reverse removal procedure. use new sealing
washers.
7.Tighten banjo bolt to
20 Nm.
8.Check/top-up engine oil level.TURBOCHARGER OIL DRAIN PIPE
Service repair no - 19.42.12
Remove
1.Disconnect battery negative lead.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Manifold
and Exhaust System - Tdi
3.Unscrew union and disconnect oil drain pipe
from cylinder lock.
4.Remove 2 bolts securing oil drain pipe to
turbocharger.
5.Remove oil drain pipe, remove and discard
gasket.
CAUTION: Plug the connection.
Refit
6.Ensure mating surfaces of oil pipe, turbocharger
and engine block are clean.
7.Reverse removal procedure. Use a new gasket.
8.Tighten oil drain pipe to turbocharger bolts to
25
Nm.
9.Check/top-up engine oil level.

19FUEL SYSTEM
4
REPAIR TURBOCHARGER ACTUATOR
Service repair no - 19.42.31
Remove
1.Remove exhaust manifold and turbocharger.
See MANIFOLD AND EXHAUST SYSTEM,
Repair, Exhaust Manifold - Tdi
2.Remove 2 nuts securing the actuator to the
turbocharger bracket.
3.Release clip and disconnect hose from actuator.
4.Remove and discard clip securing control lever
to wastegate spindle.
5.Remove turbocharger actuator.
Refit
6.Fit the replacement actuator and secure with
nuts.
7.Push the control lever as far as possible towards
the actuator and apply pressure to keep the
lever in this position.
8.Pressurise the actuator to 57 - 62 cm Hg and
hold this pressure.
CAUTION: Use only the threaded end of
the lever to make adjustments. Forcing the
complete lever in or out will change the
calibration with the possibility of damaging engine
boost.
9.Screw the lever in either direction until the eye
on the end will locate easily over the wastegate
spindle and secure with a new clip.
10.Release the pressure and tighten the locknut.
11.Refit exhaust manifold and turbocharger.
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - Tdi
TURBOCHARGER AND GASKET
Service repair no - Turbocharger - 19.42.01
Service repair no - Gasket - 19.42.25
Remove
1.Disconnect battery negative lead.
2.Remove air cleaner assembly.
See Air Cleaner
3.Remove exhaust manifold assembly.See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - Tdi
4.Remove and discard clip securing control lever
to wastegate spindle.
5.Remove 4 bolts and 2 clamp plates securing
turbocharger to exhaust manifold.
6.Remove turbocharger and discard gaskets.
Refit
7.Clean mating faces of turbocharger and exhaust
manifold.
8.Reverse removal procedure. Use new clip to
secure control lever to wastegate spindle.
Tighten to
45 Nm.
9.Check/top-up engine oil level.

Tdi
5
REPAIR FUEL LIFT PUMP
Service repair no - 19.45.09
Remove
1.Loosen unions securing fuel injection pipes to
injectors and injector pump. Remove injection
pipes.
2.Plug the connections to prevent the ingress of
foreign material.
3.Loosen unions and disconnect fuel supply and
feed hoses from fuel lift pump.
4.Plug the connections to prevent the ingress of
foreign material.
5.Remove 2 bolts securing lift pump to engine
block.
6.Remove fuel lift pump and discard gasket.Refit
7.Clean mating faces of fuel lift pump and engine
block.
8.Using a new gasket, fit fuel pump, ensure correct
location of lever with camshaft. Fit securing
bolts. Tighten to
25 Nm.
9.Connect fuel hoses to pump and secure unions.
Tighten to
33 Nm.
10.Fit injector pipes to injectors and injection pump,
and secure unions. Tighten to
28 Nm.

19FUEL SYSTEM
6
REPAIR FUEL FILTER ELEMENT
Service repair no - 19.25.07
Remove
1.Disconnect battery negative lead.
2.Clean area around filter head.
3.Place a suitable container beneath filter bowl to
collect any spillage.
4.Loosen bleed screw.
5.Loosen drain tap, allow fuel to drain into
container.
6.Unscrew filter element, discard element.
Refit
7.Clean seal and seating in filter head.
8.Lubricate filter element seal with fuel.
9.Position filter element to filter head and hand
tighten.
10.Reconnect battery negative lead.
11.Crank engine until fuel is drawn through the
system and starts.INTERCOOLER
Service repair no - 19.42.15
Remove
1.Disconnect battery negative lead.
2.Release 2 clips securing fan cowl to radiator top
cover.
3.Remove 4 bolts securing radiator top cover,
remove top cover.
4.Remove nut, bolt and washers securing
intercooler side cover bracket to bonnet [hood]
platform.
5.Release bracket from side cover lug, position
bracket and power steering reservoir aside.
6.Position side cover away from intercooler.
7.Loosen 2 clips and disconnect top hose from
intercooler.
8.Loosen 2 clips and disconnect bottom hose from
intercooler.

Tdi
7
REPAIR
9.Move intercooler upwards and clear of fan cowl.
Refit
10.Ensure locatiing lug grommets are fitted and in
good condition.
11.Ensure foam pad is in good condition and
attached to intercooler.
12.Move intercooler into position.
13.Reverse removal procedure.GLOW PLUGS
Service repair no - 19.60.31
Remove
1.Disconnect battery negative lead.
No.1 glow plug - air conditioning models
2.Release drive belt from compressor pulley.See
ENGINE, Repair, Drive Belt Renew
3.Remove 4 bolts securing compressor to front
cover, move compressor aside.
No.3 glow plug
4.Remove bolt securing Hummel valve, withdraw
valve, remove and discard 'O' ring.

19FUEL SYSTEM
8
REPAIR
All glow plugs
5.Remove terminal nut from glow plug, disconnect
wire from glow plug terminal.
6.Remove glow plug.
Refit
7.Clean glow plug and seating.
8.Coat threads of glow plug with suitable anti-seize
compound operational to a temperature of
1000°C.
9.Fit glow plug. Tighten to
23 Nm.
10.Connect wire to glow plug terminal and secure
with nut.
NOTE: Feed wire must be connected to
No. 4 glow plug terminal.
11.
No. 3 glow plug:Lubricate new 'O' ring with
engine oil and fit to Hummel valve. Fit valve and
secure with bolt. Tighten to
15 Nm.
No. 1 glow plug - air conditioning models
12.Position compressor to front cover, fit bolts.
Tighten to
25 Nm.
13.Fit drive belt to compressor pulley and adjust
tension.
See ENGINE, Repair, Drive Belt
Renew
All models
14.Reconnect battery negative lead.EGR VALVE
Service repair no - 19.45.01
Remove
1.Disconnect multiplug from EGR valve.
2.Disconnect vacuum pipe from EGR valve.
3.Remove 2 Allen screws securing EGR valve to
exhaust manifold.
4.Remove 2 bolts securing hose to EGR valve.
5.Remove EGR valve and discard gaskets.
Refit
6.Clean mating faces of EGR valve and exhaust
manifold.
7.Reverse removal procedure. Tighten bolts to
25
Nm.

19FUEL SYSTEM
10
REPAIR EGR THROTTLE POSITION SENSOR
Service repair no - 19.30.14
Remove
1.Remove 2 screws securing sensor mounting
plate to injection pump.
2.Disconnect sensor multiplug from harness.
3.Remove sensor assembly.
Refit
4.Position sensor assembly on injection pump and
fit and tighten screws.
5.Connect multiplug.
6.Adjust sensor.
See Adjustment, EGR Throttle
Position Sensor
INJECTORS
Service repair no - 19.60.10
Remove
1.Remove oil filler cap and remove sound
deadening pad from top of engine.
2.Remove high pressure pipe from relevant
injector and injection pump.
3.Disconnect spill return hose(s) from injector.
4.Plug pipes and injector connections to prevent
the ingress of dirt and foreign matter.
5.Remove nut securing injector clamp plate to
cylinder head.
6.Remove injector.
Refit
7.Reverse removal procedure. Renew copper
washer on injector. Tighten injector clamp plate
nut to
25 Nm.

Tdi
11
REPAIR FUEL INJECTION PUMP AND TIMING
Service repair no - 19.30.07
NOTE: The following text refers to a Tdi
vehicle with a manual gearbox without
electronic diesel control. Where reference
is made to the timing tool substitute the following
information for automatic and EDC variants.
If manual gearbox:Timing tool LRT-12-044 fits into
the base of the flywheel housing
If manual gearbox with EDC:Timing tool
LRT-12-085 must be used and also fits into the base
of the flywheel housing.
If automatic gearbox:Timing tool LRT-12-044 fits
into the larger bolt hole of coverplate on engine
backplate, sited near to the rear of sump. Pin locates
in ring gear.
Remove
1.Disconnect battery negative lead.
2.Remove injection pipes, pump to injector.
3.Remove oil filler cap from rocker cover.
4.Viewing valve mechanism through filler aperture,
turn crankshaft clockwise until No. 1 cylinder is
just before TDC.
5.Refit oil filler cap.
6.Remove blanking plug from flywheel housing.
7.Fit timing tool LRT-12-044 to flywheel housing,
do not engage centre pin.
8.Continue rotating crankshaft clockwise until
centre pin engages with timing slot in flywheel.
9.Remove injection pump access plate, complete
with gasket, from front cover plate.
10.Fit pin from LRT-12-045 to injection pump gear.
11.Remove drive gear to pump hub fixing bolts and
plate.

19FUEL SYSTEM
14
REPAIR ENGINE CONTROL MODULE (ECM)
Service repair no - 18.30.03
NOTE: The ECM is not a serviceable item,
in the event of failure it must be renewed.
Remove
1.Disconnect battery negative lead.
2.Remove 'A' post trim pad.
3.Loosen multi-plug screw to ECM.
4.Disconnect multi-plug from ECM.
5.Secure multi-plug and harness aside.
6.Remove retaining nuts from ECM.
7.Manoeuvre ECM from its mounted position.
Refit
8.Refitting is the reverse of removal procedure.
9.Reconnect harness plug. Ensure plug is pushed
firmly into location and retaining clip secures
plug in position.
10.Tighten screw securing multi-plug.AIRFLOW METER
Service repair no - 18.30.15
NOTE: The air flow meter is not a
serviceable item, in the event of failure it
must be renewed.
Remove
1.Disconnect battery negative lead.
2.Release vacuum tube from EGR vacuum
capsule.
3.Disconnect airflow meter multi-plug.
4.Loosen air cleaner hose to air flow meter
retaining clip.
5.Disconnect hose from airflow meter.
6.Loosen turbo charger hose to airflow meter
retaining clip.
7.Disconnect hose from airflow meter.
8.Remove meter to mounting bracket bolts.
9.Remove airflow meter.
Refit
10.Reverse removal procedure. Ensure multi-plug is
firmly reconnected and hose clamps are
securely tightened to prevent unmetered air
entering the engine.