air condition LAND ROVER DISCOVERY 1995 User Guide

GENERAL FITTING REMINDERS
5
INFORMATION JOINTS AND JOINT FACES
1.Always use correct gaskets where they are
specified.
2.Use jointing compound only when
recommended. Otherwise fit joints dry.
3.When jointing compound is used, apply in a thin
uniform film to metal surfaces; take great care to
prevent it from entering oilways, pipes or blind
tapped holes.
4.Remove all traces of old jointing materials prior
to reassembly. Do not use a tool which could
damage joint faces.
5.Inspect joint faces for scratches or burrs and
remove with a fine file or oil stone; do not allow
removed material or dirt to enter tapped holes or
enclosed parts.
6.Blow out any pipes, channels or crevices with
compressed air, fit new 'O' rings or seals
displaced by air blast.FLEXIBLE HYDRAULIC PIPES, HOSES
1.Before removing any brake or power steering
hose, clean end fittings and area surrounding
them as thoroughly as possible.
2.Obtain appropriate plugs or caps before
detaching hose end fittings, so that ports can be
immediately covered to exclude dirt.
3.Clean hose externally and blow through with
airline. Examine carefully for cracks, separation
of plies, security of end fittings and external
damage. Reject any hose found faulty.
4.When refitting hose, ensure that no unnecessary
bends are introduced, and that hose is not
twisted before or during tightening of union nuts.
5.Containers for hydraulic fluid must be kept
absolutely clean.
6.Do not store brake fluid in an unsealed
container. It will absorb water, and fluid in this
condition would be dangerous to use due to a
lowering of its boiling point.
7.Do not allow brake fluid to be contaminated with
mineral oil, or use a container which has
previously contained mineral oil.
8.Do not re-use brake fluid bled from system.
9.Always use clean brake fluid to clean hydraulic
components.
10.Fit a cap to seal a hydraulic union and a plug to
its socket after removal to prevent ingress of dirt.
11.Absolute cleanliness must be observed with
hydraulic components at all times.
12.After any work on hydraulic systems, inspect
carefully for leaks underneath the vehicle while a
second operator applies maximum pressure to
the brakes (engine running) and operates the
steering.

LUBRICANTS, FLUIDS AND CAPACITIES
3
INFORMATION Propeller shaft Front
and RearNLGI - 2 Multi-purpose Lithium based GREASE
Lubrication nipples
(hubs, ball joints
etc.)
Seat slides
Door lock striker
Brake and clutch
reservoirsBrake fluids having a minimum boiling point of 260°C (500°F) and complying with
FMVSS 116 DOT4
Engine coolant Use an ethylene glycol based anti-freeze (containing no methanol)
V8i, Tdi, Mpi with non-phosphate corrosion inhibitors suitable for use in aluminium engines to ensure
the protection of the cooling system against frost and corrosion in all seasons. Use one
part anti-freeze to one part water for protection down to -36°C (-33°F).
IMPORTANT: Coolant solution must not fall below proportions one part
anti-freeze to three parts water, i.e. minimum 25% anti-freeze in coolant otherwise
damage to engine is liable to occur. Or a maximum of 60%.
Battery lugs, Petroleum jelly.
Earthing surfacesNOTE: Do not use Silicone Grease
where paint has
been removed
Air Conditioning
System Refrigerant Use only refrigerant R134a
Compressor Oil Nippon Denso ND-oil8 Unipart ND-oil8
ABS Sensor Silicone grease: Staborags NBU - Wabco 830 502,0634
bush-rear Wacker chemie 704 - Wabco 830 502,0164
Kluber GL301
LUBRICATION PRACTICE
Use a high quality oil of the correct viscosity range and service classification in the engine during maintenance and
when topping up. The use of oil not to the correct specification can lead to high oil and fuel consumption and
ultimately to damaged components.
Oil to the correct specification contains additives which disperse the corrosive acids formed by combustion and
prevent the formation of sludge which can block the oilways. Additional oil additives should not be used. Always
adhere to the recommended servicing intervals.
WARNING: Many liquids and other substances used in motor vehicles are poisonous. They must
not be consumed and must be kept away from open wounds. These substances, among others,
include anti-freeze windscreen washer additives, lubricants and various adhesives.

MAINTENANCE
1
MAINTENANCE SERVICE SCHEDULE
This section gives information on the range of service
procedures.
Where required, instructions are given for carrying out
each service procedure, or a cross reference is given,
where the procedure can be found in this manual.
Service Schedule sheets are published separately to
reflect the maintenance needs and intervals for each
vehicle variant and model year. The procedures given
must be used in conjunction with the Service
Schedule sheets.
The Service Schedule sheets are available from:-
Land Rover Merchandising
PO Box 534
Erdington
Birmingham B24 0QS.
England.VEHICLE INTERIOR
CHECK SEATS & BELTS
Check condition and security of seats, seat belt
mountings, seat belts, buckles and opertion of inertia
seat belts. Lubricate seat tilt pivots.
CHECK OPERATION OF FOOT BRAKE AND
CLUTCH
If pedal feels 'spongy' bleed system.See BRAKES,
Repair, Brake System Bleed
or.See CLUTCH,
Repair, Bleed hydraulic system
Check all hoses and pipes for security, fractures and
leaks. Fit new hoses and pipes as necessary.
CHECK OPERATION OF LAMPS
Check operation of all lamps, horns and warning
indicators.
CHECK OPERATION OF WIPERS
Check operation of front/rear screen wipers and
washers and condition of wiper blades.
AIR BAG MODULE(S)
Check air bag module covers.
Check visually for signs of damage.
Renew every ten years.

MAINTENANCE
3
MAINTENANCE VEHICLE EXTERIOR
CHECK/ADJUST HEADLAMP ALIGNMENT
Check/adjust headlamp and auxiliary alignment.
CHECK FRONT WHEEL ALIGNMENT
Use recognised wheel alignment equipment to
perform this check and adjustment.
See STEERING,
Adjustment, Front Wheel Alignment
REMOVE WHEELS, CHECK TYRES
Check tyres (including spare) for compliance with
manufacturers' specification.
Check visually for cuts, lumps, bulges, uneven tread
wear and tread depth. Check road wheels for
damage.
Check/adjust tyre pressures.
CHECK/TIGHTEN TOWING BRACKET FITTINGSINSPECT BRAKE PADS FOR WEAR, CALIPERS
FOR LEAKS AND CONDITION
Check thickness of brake pads, fit new pads if
minimum thickness is less than 3,0mm. Check brake
pads for oil contamination. If new brake pads required.
See BRAKES, Repair, Front Brake Pads
or.See BRAKES, Repair, Rear Brake Pads
WARNING: When renewing brake pads, it
is essential that only genuine components
with correct grade of lining are used.
Always fit new pads as complete axle sets, NEVER
individually or as a single wheel set. Serious
consequences could result from out of balance
braking due to mixing of linings.
Refit road wheels
Fit road wheels in original hub position. Secure in
position with wheel nuts, do not fully tighten wheel
nuts at this stage, lower vehicle and finally tighten
wheel nuts to correct torque.
Alloy wheels:
130 Nm.
Steel wheels:130 Nm.
LUBRICATE ALL HINGES, DOOR CHECK
MECHANISMS, BONNET [HOOD] CATCHES AND
FUEL FILLER FLAP

MAINTENANCE
9
MAINTENANCE
CHECK CONDITION OF DRIVE BELT - V8i - Tdi -
Mpi
RENEW - V8i - Tdi
Renew drive belt V8i.See ENGINE, Repair, Drive
Belt Renew
Renew drive belt Tdi.See ENGINE, Repair, Drive
Belt Renew
RENEW - Mpi
1.Check condition of drive belt, renew a belt that
shows signs of wear, splitting or oil
contamination.
2.Check belt length indicator, belt must be
renewed before indicator reaches R.H. end of
slot.
3.Use 15mm ring wrench on bolt and hold
tensioner pulley fully clockwise.
4.Release drive belt from tensioner pulley and
remove ring wrench.
5.Remove belt from between pulleys.
6.Clean drive belt pulley grooves and ensure
grooves are not damaged.
7.Fit new drive belt around pulley, except
tensioner pulley, ensuring all grooves are
correctly engaged.
8.Hold tensioner pulley fully clockwise and fit drive
centrally around tensioner pulley.
RENEW ANCILLARY DRIVE BELTS
CHECK/TOP UP AUTOMATIC TRANSMISSION
FLUID LEVEL
NOTE: Transmission fluid level is checked
when fluid is cold with engine idling in
neutral.
1.Ensure vehicle is on level ground.
2.Check fluid level registers between MAX and
MIN marking on dipstick.

MAINTENANCE
11
MAINTENANCE
CHECK/ADJUST ENGINE IDLE SPEED - Tdi
For idle speed.See ENGINE TUNING DATA,
Information, 300 Tdi Engine
CHECK ENGINE IDLE SPEED - Mpi
For idle speed.See ENGINE TUNING DATA,
Information, Engine - Mpi - 2.0 Litre
CHECK/ADJUST STEERING BOX V8i - Tdi - Mpi
Check steering box for fluid leaks.
Check that there is no backlash in steering box in
straight ahead position. Adjust steering box if
necessary.
See STEERING, Adjustment, Power
Steering Box
CLEAN BATTERY CONNECTIONS
NOTE: Some 96 models are fitted with
battery backed-up sounder
See
ELECTRICAL, Repair, Battery
Remove battery terminals, clean and coat with
petroleum jelly.
A low maintenance battery is installed in vehicle.
Dependent upon climate conditions electrolyte levels
should be checked as follows:
Temperate climates every three years.
Hot climates every year.
RENEW CAMSHAFT DRIVE BELT - Tdi
Renew camshaft drive belt.See ENGINE, Repair,
Camshaft Drive Belt and Gears
The engine timing gears are driven by a flexible
rubber belt which must be renewed at intervals
determined by the severity of operating conditions.
In reasonable, temperate climate operation, renew the
belt every 120,000 km (72,000 miles) or every 6 years
whichever occurs earlier.
In adverse operating conditions such as work in dusty
atmospheres, high ambient temperatures and desert
and tropical zones, renew the belt every 60,000 km
(36,000 miles) or every 3 years whichever occurs
earlier.
CAUTION: If the drive belt is not renewed
at the correct interval, it could fail,
resulting in serious damage.
RENEW CAMSHAFT DRIVE BELT - Mpi
Renew every 160,000 km (96,000 miles) or every 6
years. In adverse conditions every 80,000 km (48,000
miles).
For details of renewing camshaft drive belt.
See
ENGINE, Repair, Camshaft Drive Belt - Mpi
CHECK CAMSHAFT DRIVE BELT - Mpi
For details of checking camshaft drive belt.See
ENGINE, Repair, Check Camshaft Drive Belt - Mpi

10MAINTENANCE
12
MAINTENANCE
EXTERNALLY CHECK INTERCOOLER FOR
OBSTRUCTION - Tdi
Clear any trapped dirt or flies from vanes of
intercooler
CLEAN INTERCOOLER ELEMENT - Tdi
Remove
1.Remove intercooler element.
2.Flush intercooler with ICI 'GENKLENE'or
à oD-SOLVE' propriety cleaner, following the
manufacturer's instructions.
3.Dry the intercooler completely ensuring that no
liquid remains in the element.
Refit
4.Refit intercooler element.UNDER VEHICLE MAINTENANCE
Vehicles operating under severe conditions of dust,
sand, mud and water should have oils changed and
lubrication carried out at more frequent intervals than
is recommended in maintenance schedules.
RENEW ENGINE OIL AND FILTER - Tdi
CAUTION: Serious damage to the
turbocharger will result if engine is run
above idling speed before oil pressure is
restored.
RENEW ENGINE OIL - V8i
RENEW ENGINE OIL AND FILTER - V8i
CAUTION: To prevent an airlock occuring
after removing filter, fill new filter with oil
and fit immediately after removing old
filter. If airlock does occur fill oil pump with
petroleum jelly.
RENEW ENGINE OIL AND FILTER - Mpi
CHECK/TOP UP MANUAL GEARBOX OIL - V8i
1.Site vehicle on lift or level ground.
2.Remove oil filler level plug. If necessary, inject
new oil into the gearbox until it runs out of filler
hole. Fit plug. Tighten to
30 Nm.
RENEW MANUAL GEARBOX OIL - Tdi - Mpi
RENEW MANUAL GEARBOX OIL - V8i

MAINTENANCE
17
MAINTENANCE
CHECK/TIGHTEN FRONT AND REAR AXLE
SUSPENSION LINK FIXINGS, CHECK CONDITION
OF MOUNTING RUBBERS
DRAIN FUEL SEDIMENTER - Tdi
Fuel sedimenter
The sedimenter is attached to left-hand side of
chassis frame near fuel tank. It increases the working
life of the fuel filter by removing larger droplets of
water and larger particles of foreign matter from fuel.
Drain off water
1.Loosen drain plug, allow water to run out.
Tighten plug immediately pure diesel fuel starts
to flow.
RENEW FUEL FILTER
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction regarding fuel handling are
strictly adhered to when carrying out following
instructions.
See INTRODUCTION, Information,
Fuel Handling Precautions
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
1.Depressurise fuel system.
See FUEL SYSTEM,
Repair, Depressurising Fuel System
2.The fuel line filter is located on right hand
chassis side member forward of fuel tank filler
neck. Access to filter is gained through right
hand rear wheel arch.
3.Thoroughly clean area around hose connections
to prevent ingress of foreign matter into fuel
system.
4.Loosen two fuel unions and remove hoses from
filter canister.
5.Release securing bolt and bracket, remove filter
from chassis side member.
6.Fit a new filter observing direction of flow arrow
on canister.
7.Fit inlet and outlet hoses. Tighten to
30 Nm.
8.Refit fuel pump relay.
9.Reconnect battery negative lead.
10.Recode radio.
11.Start engine and inspect hose connections for
fuel leaks.

10MAINTENANCE
18
MAINTENANCE
ABS VEHICLES - CHECK ROAD WHEEL SPEED
SENSOR ELECTRICAL HARNESS FOR DAMAGE
RENEW OXYGEN SENSORS
See EMISSION CONTROL, Repair, Heated
Oxygen Sensor (HO2S)
RENEW CATALYTIC CONVERTERS
See MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust System Complete
REPORT ANY UNUSUAL FEATURES OF VEHICLE
CONDITION AND ADDITIONAL WORK REQUIREDCARRY OUT ROAD TEST
For details of dynamometer testing.See
INTRODUCTION, Information, Dynamometer
Testing - Non Anti-lock brake vehicles See
INTRODUCTION, Information, Dynamometer
Testing - Vehicles with Anti-lock brakes (ABS)
Check following items:
1.Inhibitor switch only operates in P and N.
2.Engine for excessive noise.
3.Clutch for slip, judder or spin.
4.Automatic gear selection/shift speeds.
5.Gear selection/noise - high/low range.
6.Steering for abnormal noise/effort.
7.Steering for free play.
8.All instruments, gauges and warning indicators.
9.Heater and air conditioning systems.
10.Heated rear screen.
11.Shock absorbers - ride irregularities.
12.Foot brake, on emergency stop, pulling to one
side, binding, pedal effort.
13.Parkbrake efficiency.
14.Seat reclining and latching.
15.Fully extend seat belt, check operation of
retraction and latching. Inertia belts lock when
snatched or vehicle on slope.
16.Road wheel balance.
17.Transmission for vibrations.
18.Body noises, squeaks and rattles.
19.Excessive exhaust smoke.
20.Engine idle speed.
21.Endorse service record.
22.Report any unusual features of vehicle condition
and additional work required.
ENDORSE SERVICE RECORD

MAINTENANCE
19
MAINTENANCE
RESET EMISSION MAINTENANCE REMINDER -
USA
The emission maintenance reminder is designed to
activate at 52,500 and 105,000 miles respectively and
will illuminate a 'Service Engine' red warning light in
instrument binnacle.
The emission maintenance reminder must be reset
after required maintenance has been carried out and
a new tamperproof label fitted by a Land Rover of
North America dealer. This emission maintenance
reminder is part of the Emission Control System
Reset
1.The control unit is located in the passenger
footwell.
2.Identify control unit and remove from plug.
3.Remove tamperproof label to reveal access hole
for resetting.
4.Place a thin metallic probe into access hole and
momentarily electrically short between reset pins
inside unit.RECOMMENDED SERVICE ITEMS
Refer Service Schedule sheets for intervals.
Clean sunroof drain tubes, clean and lubricate guide
rails and slides.
Renew the hydraulic brake fluid.
See BRAKES,
Repair, Brake System Bleed
Renew all hydraulic brake fluid, seals, brake servo
filter and flexible hoses.
All working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.
ABS vehicles only - renew hydraulic brake fluid and
flexible hoses examine the working surfaces of the
caliper cylinders and renew the seals or cylinders
where necessary.
Air cleaner - When the vehicle is used in dusty or field
conditions or deep wading, frequent attention to the
air cleaner may be required.
ABS vehicles used extensively in arduous off-road
conditions - check the rear wheel road speed sensor
for abrasive wear.