petrol LAND ROVER DISCOVERY 1995 User Guide

EMISSION CONTROL
1
FAULT DIAGNOSIS REV: 09/95 TESTING EVAPORATIVE EMISSION CONTROL -
PRE ADVANCED EVAPS
The following pressure test procedure is intended to
provide a method for ensuring that the system does
not leak excessively and will effectively control
evaporative emissions.
Equipment required.
Nitrogen cylinder (compressed air may be used to
pressure the system when there has NEVER been
fuel present in the fuel or evaporative control
systems).
Water manometer (0 - 30" H2O or more).
Pipework and a "T" piece.
Method.
1.Ensure that there is at least two gallons of fuel in
the petrol tank unless there has never been any
fuel in the system.
2.Disconnect, at the adsorption canister, the pipe
to the vapour separator.
3.Connect this pipe to the nitrogen cylinder and
the water manometer using the "T" piece.
4.Pressurize the system to between 26.5 and 27.5
inches of water, allow the reading to stabilize,
then turn off the nitrogen supply.
5.Measure the pressure drop within a period of 2
minutes 30 seconds. If the drop is greater than
2.5 inches of water the system has failed the
test. Note that a fully sealed system will show a
slight increase in pressure.
6.Should the system fail the test, maintain the
pressure in the system and apply a soap
solution round all the joints and connections until
bubbles appear to reveal the source of the leak.
7.Repeat the test and if successful, dismantle the
test equipment and reconnect the pipe to the
adsorption canister.LEAK DETECTION PROCEDURE - ADVANCED
EVAPS
1.Connect TestBook to the vehicle and confirm
that the fault code(s) displayed relate to an
EVAP system fault.
2.Examine components in fuel and EVAP system
for damage or poorly connected joints.
3.Repair or replace components to rectify any
faults found, then reset the Check Engine light
using TestBook.
4.Carry out Drive Cycle,
See Drive Cycle -
Advanced EVAPS
5.Using TestBook confirm that the Evaporative
Loss Control (ELC) Inspection and Maintenance
(IM) flag has cleared. This procedure should
confirm that the ELC test was carried out during
the drive cycle and that the fault was cured.
6.If the IM flag is still shown, use TestBook to
interrogate the engine management system to
ascertain which of the following situations exists:
·If a fault code is shown then further investigation
is required, proceed to the next step.
·If the IM flag is still shown, but no faults are
indicated the conditions for the ELC check have
not been met and the drive cycle must be
repeated.
7.Connect the Leak Detection/EVAP Diagnostic
Station to the vehicle and carry out the
procedures given in the operating instructions
supplied with the equipment.
8.Rectify faults indicated by the Leak
Detection/EVAP Diagnostic Station and return to
step 4.

MFI
1
FAULT DIAGNOSIS ENGINE TUNING
Circuit fault diagnosis may be carried out on all V8i
vehicles, using Testbook. Testbook will guide the
operator by visual prompts through a series of
diagnostic checks.
Before commencing any fault diagnosis, the following
preminary checks must be carried out.
Preliminary checks
CAUTION: Catalyst exhaust: If engine is
misfiring or fails to start within 12 seconds
the cause must be rectified. Failure to do
so will result in irreparable damage to the
catalysts. After rectification the engine must be
run at 1500 rev/min (no load) for 3 minutes to
purge any accumulation of fuel in the system.
1.Check that the inertia fuel shut off switch is not
tripped.
2.Check fuse in main fuse panel.
3.Check for ample fuel in tank.
4.Check air inlet system for possible leaks into the
intake manifold.
5.Check HT cables for correct firing order and
routing.
6.Check ignition timing.
Only when the above checks have been carried out,
should circuit diagnosis begin.
See Electrical
Trouble Shooting Manual.
INJECTOR TESTS
NOTE: Before removing any of the
injectors, remove and examine the spark
plugs, check for consistent colouration of
plugs. A leaking injector will result in the
appropriate spark plug being 'sooted up'.
The following test may only be carried out using
suitable injector test equipment.
Leak Test
Leak test with the injectors closed but pressurise to
2.54 Kgf/cm
2. No injector should leak more than 2
drops of fuel per minute.
Fuel Delivery Test
Fuel delivery test with the injector open and
pressurised as above, fuel delivery from each injector
should be 160-175cc per minute using white spirit, or
180-195cc per minute using petrol at 20°C±2°C.

19FUEL SYSTEM
24
REPAIRADD: 09/95 Refit
29.Fit NEW pump seal to tank opening.
30.Carefully lower pump into tank opening, pressing
firmly on the pump top flange to allow correct
positioning.
NOTE: Ensure location tag on pump top
flange is engaged correctly to tank
opening lip.
31.Fit locking ring and tighten to
35 Nmusing
service tool LRT-19-009.
32.Fit vent hose to fuel tank clips and connect to
pressure sensor.
33.With assistance, fit fuel tank into position.
34.Fit fuel tank cradle and secure with nuts and
bolts.
35.Align upper fuel tank strap and secure with nut
and bolt.
36.Fit NEW clip to fuel filler neck hose.
37.Connect fuel filler neck internal breather to tank.
38.Connect fuel filler neck hose to tank.
39.Position fuel filler neck hose clip and tighten until
head shears.
40.Connect vent line quickfit connector to
liquid/vapour separator.
41.Connect vent line hose connection.
42.Position anti-roll [sway] bar straps and secure
with nuts and bolts.
43.Remove stand(s) and lower vehicle.
44.Connect both fuel lines to the pump by pushing
the connectors down each line square to the
pump connection until the connectors positively
latches.
45.Connect multiplugs to fuel pump and pressure
sensor.
46.Reconnect battery negative lead.
47.Refill tank with drained fuel.
48.Run the engine to check for any fuel leaks.
49.Fit access panel and secure with screws.
50.Reposition loadspace sound insulation and
carpet.
51.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair, rear
compartment trim panels
52.Fit tail door tread strip and secure with screws.FUEL TANK - DRAINING - ADVANCED EVAPS
Service repair no - 19.55.02
WARNING: Before removing the fuel tank
it must be drained.
WARNING: Petrol/gasoline vapour is
highly flammable and in confined spaces
is also explosive and toxic. Always have a
fire extinguisher containing FOAM, CO2, GAS or
POWDER close at hand when handling or draining
fuel. See Introduction
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
NOTE: Assuming the fuel tank is FULL
drain the following quantities:
Renew Fuel pump = 9 Litres (2.4 US Gallons)
Renew Fuel filler neck = 22 Litres (6 US Gallons)
Renew Fuel tank = COMPLETE DRAIN
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Remove 6 screws securing tail door tread strip
and remove tread strip.
4.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair,

CRUISE CONTROL
1
FAULT DIAGNOSIS ROAD TEST
CAUTION: Do not engage cruise control
when vehicle is being used in low transfer
gear or reverse.
WARNING: The use of cruise control is not
recommended on winding, snow covered
or slippery roads or in heavy traffic
conditions where a constant speed cannot be
maintained.
1.Start engine, depress main control switch to
actuate cruise control system. Accelerate to
approximately 50 km/h, (30 mph), operate
'set/acc'switch, immediately release switch,
remove foot from accelerator pedal. Vehicle
should maintain speed at which'set/acc'switch
was operated.
2.Operate'set/acc'switch and hold at that
position, vehicle should accelerate smoothly until
switch is released. Vehicle should now maintain
new speed at which'set/acc'switch was
released.
3.Momentarily touch and release'set/acc'switch,
vehicle speed should increase 1.6 km/h (1 mph)
for each touch. Note that five touches will
increase speed 8 km/h (5 mph).
4.Apply'res/decel'switch while vehicle is in cruise
control mode, cruise control should disengage.
Slow to approximately 55 km/h, (35 mph)
operate'res/decel'switch, immediately release
switch and remove foot from accelerator, vehicle
should smoothly accelerate to previously set
speed. Increase speed using accelerator pedal,
release pedal, vehicle should return to previously
set speed.
NOTE: The cruise control system fitted to
the diesel engine is not as responsive as
that fitted to the petrol engine, due to the
characteristics of diesel engines. Therefore, at
speeds below approx. 65 km/h (40 mph), the
vehicle speed may drop when cruise is selected
and then slowly regain the 'set' speed.5.Operate brake pedal, cruise control system
should immediately disengage returning vehicle
to driver control at accelerator pedal. Operate
'res/decel'switch, vehicle should accelerate to
previously set speed without driver operation of
accelerator pedal.
6.Operate'res/decel'switch and allow vehicle to
decelerate to below 42 km/h, (26 mph). Operate
'res/decel'switch, cruise control system should
remain disengaged.
7.Operate'set/acc'switch below 40 km/h, (28
mph), cruise control system should remain
disengaged. Accelerate, using accelerator pedal
to above 45 km/h, (28 mph), operate'res/decel'
switch, and remove foot from accelerator pedal,
vehicle should smoothly adjust to previously
memorised speed.
8. Automatic vehicles- select neutral, system
should disengage.Manual vehicles- depress
clutch, system should disengage.
9.Cruise at 80 km/h (50 mph), declutch, select
neutral, remove foot from clutch. Operate
'res/decel'switch. Engine should rev to 5000
rev/min, cruise control disengages, engine
returns to idle.
10.Engage forward gear. Operate'res/decel'
switch. Remove foot from accelerator. Speed
should accelerate to previous set speed.
11.Depress main control switch in control system
should immediately disengage and erase
previously set speed from ECU memory.
See
Electrical Trouble Shooting Manual.
ELECTRICAL TESTS
Electrical functionality can be checked using
TestBook.
CABLE SETTING - TDi AUTOMATIC MODELS
1.An incorrectly adjusted kickdown cable can
prevent correct operation of the cruise control
system.
See AUTOMATIC GEARBOX,
Adjustment, kickdown cable adjustment.

ZF
15
REPAIR GOVERNOR ASSEMBLY
Service repair no - 44.22.01
Remove
1.Remove transfer gearbox.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Drain oil from automatic gearbox.
3.Remove bolts securing left hand mounting
bracket to extension housing and withdraw
bracket.
4.Remove transfer gear lever housing securing
bolts and move housing aside.
5.Remove extension housing ensuring seal is not
damaged, remove and discard gasket.
6.Remove extension shaft retaining bolt, withdraw
shaft and discard 'O' ring seal. If Tdi vehicle
remove spacer.
7.Remove governor assembly.
8.Remove park gear from governor assembly.
9.Detach governor housing.
10.Remove security clip and counter weight.
11.Remove and discard 'O' ring seal from output
shaft and three seal rings from 'F' clutch
housing.
12.Clean all components.
13.If necessary detach parking pawl by removing
guide plates and withdrawing mechanism.Refit
14.Refit parking pawl mechanism if removed.
15.Fit and lubricate new seal rings to 'F' clutch
housing shaft, ensure they are correctly seated.
16.Apply petroleum jelly to a new 'O' ring seal. Fit to
output shaft
17.Fit park gear to governor assembly tightening
screws to correct torque.
18.Fit governor assembly to output shaft.
19.Fit extension shaft with spacer if Tdi. Fit new 'O'
ring under bolt head.
20.Fit extension housing, avoid damaging seal.
Tighten to
23 Nm.
21.Refit transfer gear lever housing to extension
housing.
22.Refit mounting bracket to extension housing.
Tighten to
52 Nm.
23.Refit transfer gearbox.See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
24.Refill automatic gearbox with correct grade of oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

44AUTOMATIC GEARBOX
16
REPAIR GOVERNOR HUB
Service repair no - 44.22.04
Remove
1.Remove transfer box.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Remove transfer gear selector housing.
3.Loosen nine bolts holding extension housing.
4.Remove extension housing ensuring that seal is
not damaged, discard gasket.
5.Remove extension shaft and retaining bolt with
'O' ring. If Tdi vehicle remove spacer.
6.Remove governor assembly with parking wheel.
7.Remove two screws holding governor housing.
8.Remove two bolts, remove parking wheel.
Discard governor hub.
9.Remove security clip and counter-weight.
10.Remove 'O' ring from output shaft and discard.
11.Remove three seal rings from 'F' clutch housing
shaft.
12.Inspect all parts for damage or wear, replace if
necessary.
Refit
13.Fit counterweight and security clip into new
governor hub.14.Secure governor housing to governor hub.
Tighten to
10Nm.
15.Fit parking wheel to governor hub. Tighten to10
Nm.
16.Fit three new seal rings onto F clutch housing
shaft, fit 'O' ring onto output shaft.
NOTE: To aid fitting of 'O' ring apply
petroleum jelly.
17.Push governor assembly and parking wheel onto
output shaft until seated.
NOTE: Apply petroleum jelly to 'O' ring.
Ensure seal rings are snapped together
and seated.
18.Fit new gasket to rear of gearbox. Fit extension
housing, avoid damaging seal.
19.Fit extension shaft,and spacer if Tdi, apply
Loctite 270 to retaining bolt. Using a new 'O'
ring, tighten bolt to
42 Nm.
20.Tighten nine extension housing nine bolts to23
Nm.
21.Fit transfer gear selector housing, tighten three
bolts to
25 Nm.
22.Refit transfer box.

ZF
17
REPAIR PARKING PAWL MECHANISM
Service repair no - 44.28.07
Remove
1.Remove transfer box.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Remove transfer gear selector housing.
3.Loosen nine bolts holding extension housing.
4.Remove extension housing ensuring that seal is
not damaged, discard gasket.
5.Remove extension shaft and retaining bolt with
'O' ring. If Tdi vehicle, remove spacer.
6.Remove governor assembly with parking wheel.
7.Remove guide plate bolt.
8.Remove plate and guide plate from gearbox
case.
9.Remove pin, pawl and spring.
CAUTION: When removing assembly.
Avoid damaging parts which could weaken
spring tension.
10.Inspect all parts for wear or damage. Replace if
necessary.
Refit
11.Fit pin and leg spring, locate spring correctly.
12.Fit pawl to pin. Locate spring leg into hole in
pawl to create tension in spring.
13.Fit plate and guide plate. Tighten to
10 Nm.
14.Push governor assembly with parking wheel
onto output shaft until seated.
NOTE: Apply petroleum jelly to 'O' ring.
Ensure seal rings are snapped together
and seated.
15.Fit new gasket to rear of gearbox. Fit extension
housing, taking care not to damage seal or
assembly.
16.Fit extension shaft with spacer if Tdi and
retaining bolt with new 'O' ring.
17.Fit extension housing, tighten nine bolts to
23Nm.
18.Fit transfer gear selector housing, tighten three
bolts to
25 Nm.
19.Refit transfer box.

ZF
19
REPAIR 6.Screw in two bolts, diagonally opposite each
other. Tap lightly using a soft headed mallet to
remove pump assembly from intermediate plate.
7.Remove shaft sealing ring and 'O' ring from
pump housing and discard.
8.Using oil seal replacer LST108 fit shaft seal ring
into pump housing.
9.Fit 'O' ring onto circumference of pump housing.
10.Align dowel with hole in intermediate plate and
press pump housing home.11.Fit pump housing to intermediate plate, tighten
eight bolts to
10 Nm.
12.Place bell housing and intermediate plate
assembly on bench, front face up. Using oil
pump rotation sleeve LST111, check that pump
gears rotate freely.
13.Before fitting intermediate plate and bell housing
assembly,check that thrust washer and axial
cage are seated on A clutch housing.
14.Place gasket and disc washer onto bell housing
and intermediate plate assembly using
Petroleum Jelly.
15.Fit bell housing and intermediate plate assembly
to gearcase. Tighten twelve bolts to
46 Nm.
16.Place end float gauge LST111 onto pump
housing and check that axial play is between
0.2-0.4 mm. Replace existing washer, situated at
rear of intermediate plate, with a suitable washer
to give required end float.
17.Refit torque converter into housing using torque
converter handles 18G1501, checking that
dimension from converter fixing bolt boss to
converter housing face is 50 mm. This shows
converter is properly seated in housing.
18.Refit gearbox/transfer box assembly.
See
LT230T Transfer Gearbox

44AUTOMATIC GEARBOX
20
REPAIR ELIMINATING LEAKS BETWEEN GEARBOX
HOUSING AND INTERMEDIATE PLATE
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Remove twelve hexagonal bolts (inner ring
pattern).
4.Remove bell housing/intermediate plate
assembly from gearbox case and discard
gasket.
5.Place new gasket onto intermediate plate using
Petroleum Jelly.
6.Before fitting bell housing assembly check that
thrust washer and axial cage are seated on A
clutch housing.
7.Fit bell housing assembly with disc washer to
gearcase. Tighten twelve bolts to
46Nm.
8.Place end-float gauge LST111 onto pump
housing and check that axial play is between
0.2-0.4 mm. Replace existing washer, situated at
rear of intermediate plate, with a suitable washer
to give required end-float.
9.Refit torque converter using torque converter
handles 18G1501. Checking that dimension
from converter fixing boss to converter housing
case is 50mm. This dimension shows converter
is properly seated.
10.Refit gearbox/transfer box assembly.
See
LT230T Transfer Gearbox

ZF
21
REPAIR REPLACING PUMP
Service repair no - 44.32.01
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Remove twelve bolts (inner ring pattern).
4.Remove bell housing and pump assembly from
gearbox case, discard gasket.
5.Remove eight bolts on rear of pump.
6.Screw in two bolts,diagonally opposite each
other, tap lightly using a soft headed mallet to
free pump assembly from intermediate plate.
7.Fit new pump assembly, aligning dowel with hole
in intermediate plate, press pump housing home.
8.Secure pump housing to intermediate plate
using eight hexagonal bolts. Tighten to
10 Nm.
9.Place bell housing and intermediate plate
assembly on bench, front face up. Using oil
pump rotation sleeve LST111, check that pump
gears rotate freely.
10.Before replacing intermediate plate/bell housing
assembly check that thrust washer and axial
cage are seated on A clutch housing.
11.Place new gasket and disc washer onto bell
housing and intermediate plate assembly using
a Petroleum Jelly.
12.Fit bell housing and intermediate plate assembly,
tighten twelve bolts to
46 Nm.