wheel bolt torque LAND ROVER DISCOVERY 1995 User Guide

FRONT AXLE AND FINAL DRIVE
1
REPAIR FRONT AXLE ASSEMBLY
Service repair no - 54.15.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets.
Refit bolts to prevent oil leakage.
9.Remove ABS sensor, if applicable.
10.Remove bolts from brake calipers and tie to one
side.
11.Remove nuts and washers securing shock
absorbers to axle.
12.Disconnect drag link from swivel pin housing
arm.
13.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
14.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
15.Lower axle assembly and remove road springs.
16.Disconnect anti-roll[sway] bar link.
See FRONT
SUSPENSION, Repair, Anti-Roll[Sway] Bar
Ball Joint Links
17.Remove axle assembly.
Refit
18.Position axle under vehicle, supporting left side
of axle.
19.Reverse removal procedure.
20.Tighten propeller shaft bolts to
47 Nm.
21.Tighten panhard rod to axle bracket to88 Nm.
22.Tighten drag link to hub arm to40 Nm.
23.Tighten upper swivel pin bolts.See
Specifications, torque, Torque Values
24.Tighten radius arms to axle bolts to197 Nm.
25.Tighten radius arms to chassis side member
nuts to
197 Nm.
26.Tighten track rod end to40 Nm.
Fit new split [cotter] pin.

FRONT AXLE AND FINAL DRIVE
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
FRONT AXLE
Hub driving member to hub 65........................................................................ *
Brake disc to hub 73.......................................................................................
Stub axle to swivel pin housing 65.................................................................. *
Brake caliper to swivel pin housing 82............................................................
Upper swivel pin to swivel pin housing 78...................................................... *
Upper swivel pin to swivel pin housing ABS 65..............................................
Lower swivel pin to swivel pin housing 78...................................................... *
Lower swivel pin to swivel pin housing ABS 25.............................................. *
Oil seal retainer to swivel pin housing 11........................................................
Swivel bearing housing to axle case 73.......................................................... *
Pinion housing to axle case 41.......................................................................
Crown wheel to differential housing 58...........................................................
Differential bearing cap to pinion housing 90..................................................
Differential drive flange to drive shaft 47.........................................................
Mudshield to bracket lower swivel pin 11........................................................
Disc shield to bracket lower ABS 9................................................................
Bevel pinion nut 130........................................................................................
Draglink to hub arm 40....................................................................................
Panhard rod to axle bracket 88.......................................................................
Radius arm to axle 190....................................................................................
Radius arm to chassis side member 190.........................................................
NOTE: * These bolts to be coated with Loctite 270 prior to assembly.

STEERING
5
FAULT DIAGNOSIS Symptom :-
Steering excessively light/sensitive. Excessive
freeplay at steering wheel.
1.Are steering box adjustments correct?
NO -
See Adjustment, Power Steering Box
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is within warranty, it must be
returned to manufacturer. No attempt must be
made to introduce backlash.
YES - Suspect worn panhard rod or radius arm
bushes Check condition of ball joints and
the lower steering column shaft universal
joints for wear.
See Repair, Lower
Steering Shaft and Universal Joints
Symptom :-
Steering vibration, road wheel shimmy - wobble.
Vibration through the steering linkage powerful
enough to induce high frequency oscillation of the
steering wheel, is generally caused by out of balance
road wheels. However there are a number of other
possible causes of this symptom which if severe, may
be described as shimmy or wobble. Regardless of the
terminology used by the owner/driver to describe the
symptoms, the following diagnostic checks should be
carried out in the order presented.
1.Check the tyres and balance of the road wheels.
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres See
WHEELS AND TYRES, Fault diagnosis, Fault
- Symptoms See WHEELS AND TYRES,
Repair, Wheel Balancing
2.Check the steering hydraulic damper function.
See Steering Damper
3.Check steering column universal joints for wear
and correct alignment.
See Repair, Lower
Steering Shaft and Universal Joints
4.Check steering linkage ball joints for wear,
correct alignment and security, including steering
box and tie rod.
See Steering Linkage Inspect
5.Check all front suspension rubbers for wear.
Check all fixing torques, including radius arm
bushes, panhard rod and anti-roll [sway] bar.
See FRONT SUSPENSION, Repair, Panhard
Rod See FRONT SUSPENSION, Repair,
Radius Arm See FRONT SUSPENSION,
Repair, Anti-Roll[Sway] Bar Assembly See
FRONT SUSPENSION, Repair, Front Shock
Absorber
6.Fit new radius arm bushes using NTC 6860. Fit
harmonic damper if vehicle has air suspension.
Fit new nuts, bolts and washers.
7. Coil spring vehicles only- If problem persists
fit damper kit STC 241 (2 off front) and STC
1474 (2 off rear). Road test vehicle.
8.Check the power steering box adjustments and
operation.
See Overhaul, Power Steering Box
9.Check the hub bearing end floats and determine
the condition of the hub bearings. As applicable.
See FRONT AXLE AND FINAL DRIVE, Repair,
Front Hub Assembly
10.Check the resistance and condition of the
swivels.
See FRONT AXLE AND FINAL
DRIVE, Description and operation,
Description
If problem is not diagnosed: Repeat
checks starting at 1.
11.Carry out a full steering geometry check.
See
INTRODUCTION, Information, Steering

57STEERING
2
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Ball joint nuts 40..............................................................................................
Clamp bolt nuts 14..........................................................................................
Steering column bracket nuts 22....................................................................
Steering wheel nut 50.....................................................................................
Tie bar to mounting nut 110.............................................................................
Universal joint pinch bolt 25............................................................................
PAS box
Adjuster locknut 60.................................................................................
Drop arm nut 176....................................................................................
Sector shaft cover to steering box 75.....................................................
Steering box to chassis 81.....................................................................
Steering box fluid pipes 14mm thread 15...............................................
Steering box fluid pipes 16mm thread 20...............................................
Tie bar 81...............................................................................................
PAS pump
High pressure fluid pipe 20.....................................................................
Power steering pump mounting 35.........................................................
Pulley bolts, power steering pump 10....................................................
Hose clamp 3........................................................................................
Front mounting plate bolts 9..................................................................
PAS reservoir
Hose clamp 3........................................................................................
* Torque values below are for all screws and bolts used except for those that are specified otherwise.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................