LAND ROVER DISCOVERY 1995 Owner's Manual
Manufacturer: LAND ROVER, Model Year: 1995, Model line: DISCOVERY, Model: LAND ROVER DISCOVERY 1995Pages: 873, PDF Size: 12.89 MB
Page 21 of 873
GENERAL SPECIFICATION DATA
3
INFORMATION ENGINE 4.0 V8
Type 4.0 litre V8.................................................................................
Number of cylinders Eight, two banks of four.........................................................
Bore 94.00 mm................................................................................. 3.70 in
Stroke 71.12 mm............................................................................... 2.80 in
Capacity 3950 cm
3........................................................................... 241 cu in
Valve operation Overhead by push-rod................................................................
High Compression Low Compression
Compression ratio 9.35:1............................................................ 8.2:1
Valve operation Overhead by push-rod................................................................
Maximum power: 9.35:1 140kW at 4750 rev/min..............................
8.2:1 132kW at 4750 rev/min................................
Crankshaft
Main journal diameter 63.500 - 63.487 mm....................................................... 2.50 - 2.4995 in
Crankpin journal diameter 55.513 - 55.500 mm................................................ 2.1855 - 2.1850 in
Crankshaft end thrust/end float Taken on thrust washers of centre main bearing........................................
0.10 - 0.20 mm 0.004 - 0.008 in
Main bearings
Number and type 5, Vandervell shells..............................................................
Material Lead bronze with lead-indium overlay............................................................................
Diametrical clearance 0.015 - 0.060 mm....................................................... 0.0006 - 0.0024 in
Connecting rods
Type Horizontally split big-end, plain small-end.................................................................................
Length between centres 155.12 - 155.22 mm................................................... 6.1071 - 6.1110 in
Big-end bearings
Type and material Vandervell VP3 Lead bronze with lead-indium overlay............................................................
Diametrical clearance 0.015 - 0.016 mm....................................................... 0.0006 - 0.0024 in
Piston pins
Length 60.00 - 60.50 mm.............................................................................. 2.3622 - 2.3819 in
Diameter 23.995 - 24.000 mm.......................................................................... 0.9447 - 0.9449 in
Fit-in connecting rod Press fit.........................................................
Clearance in piston 0.015 - 0.006 mm.......................................................... 0.0006 - 0.0002 in
Pistons
Clearance in bore, measured at bottom
of skirt at right angles to piston pin 0.020 - 0.050 mm................................... 0.0008 - 0.0020 in
Page 22 of 873
04GENERAL SPECIFICATION DATA
4
INFORMATION Piston rings
Number of compression rings 2..........................................
Number of control rings 1....................................................
No 1 compression ring Nitrided steel barrel faced.....................................................
No 2 compression ring Tapered spherical barrel marked 'TOP'.....................................................
Width of compression rings 1.478 - 1.49 mm.............................................. 0.0582 - 0.0587 in
(Top) 1.21 - 1.23 mm................................ 0.0476 - 0.0484 in
Compression ring gap 0.40-0.65 mm...................................................... 0.0157 - 0.0256 in
(Top) 0.3 - 0.5 mm................................ 0.0118 - 0.0197 in
Oil control ring type Aclonoform..........................................................
Oil control ring width 3.0 mm......................................................... 0.1181 in
Oil control ring rail gap 0.38-1.40 mm..................................................... 0.0150 - 0.0551 in
Camshaft
Location Central...........................................................................
Bearings Non serviceable...........................................................................
Number of bearings 5..........................................................
Drive Chain 9.52 mm pitch x 54 pitches..................................................................................
Camshaft End Float 0.076 - 0.355 mm......................................................... 0.003 - 0.014 in
TappetsHydraulic self-adjusting ...........................................................................
Valves
Length: Inlet 116.59 - 117.35 mm.................................. 4.590 - 4.620 in
Exhaust 116.59 - 117.35 mm........................... 4.590 - 4.620 in
Seat angle: Inlet 46°-46°25' ..................................
Exhaust 46°-46°25' ...........................
Head diameter: Inlet 39.75 - 40.00 mm.................................. 1.565 - 1.575 in
Exhaust 34.227 - 34.48 mm........................... 1.3475 - 1.3575 in
Stem diameter: Inlet 8.664 - 8.679 mm.................................. 0.3411 - 0.3417 in
Exhaust 8.651 - 8.666 mm........................... 0.3406 - 0.3412 in
Stem to guide clearance: Inlet 0.025 - 0.066 mm.................................. 0.0010 - 0.0026 in
Exhaust 0.038 - 0.078 mm........................... 0.0015 - 0.0031 in
Valve lift (Inlet and Exhaust) 9.94 mm............................................ 0.3913 in
Valve spring length fitted 40.4 mm (1.59 in) at pressure of 29.5 kg (65 lb)..................................................
Lubrication
System type Wet sump, pressure fed.....................................................................
Oil pump type Rotor...................................................................
Oil pressure 2.11 to 2.81 kg/cm
2(30 to 40 psi) at 2400 rev/min with ......................................................................
engine warm
Oil filter-internal Wire screen, pump intake filter in sump................................................................
Oil filter-external Full flow, self-contained cartridge...............................................................
Page 23 of 873
GENERAL SPECIFICATION DATA
5
INFORMATION FUEL SYSTEM 3.9 V8i
Fuel system type Lucas 14CUX hot wire system electronically controlled..............................................................
Fuel pump-make/type ACX delco high pressure electrical, immersed in the......................................................
fuel tank
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Airflow Sensor
Make and type Lucas 'Hot Wire' 5AM.................................................................
Injectors
Make and type Lucas 8NJ.................................................................
Electronic Control Unit
Make and type Lucas 14CUX.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................
Coolant temperature sensor
Make and type Lucas 3TT.................................................................
Bypass Airvalve (Stepper motor)
Make and type Lucas 2ACM.................................................................
Throttle potentiometer
Make and type Lucas 215SA.................................................................
Lambda sensor - catalyst vehicles
Make and type Lucas 3LS.................................................................
Page 24 of 873
04GENERAL SPECIFICATION DATA
6
INFORMATION FUEL SYSTEM (GEMS) 4.0 V8 ENGINE
Type Sagem - Lucas Gems 8 hot wire system electronically.................................................................................
controlled
Fuel pump-make/type High pressure electrical, immersed in the fuel tank......................................................
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Mass airflow sensor
Make and type Lucas 'Hot Wire' 20AM.................................................................
Injectors
Make and type Lucas D1000.................................................................
Electronic Control Module
Make and type Lucas GEMS 8.3.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Coolant temperature sensor
Make and type Lucas 8TT.................................................................
Bypass Air valve (Stepper motor)
Make and type Lucas 3ACM.................................................................
Throttle position sensor
Make and type Lucas 3TP.................................................................
Heated oxygen sensor - catalyst vehicles
Make and type Lucas 4LS.................................................................
Camshaft position sensor
Make and Land Rover part no. Lucas ERR6170.........................................
Crankshaft position sensor
Make and type Lucas 3VRS, Honeywell ERR6049.................................................................
Knock sensor
Make and type Lucas 2KS.................................................................
Intake air temperature sensor
Make and type Lucas 10TT.................................................................
Ignition coils
Make and type Lucas 2DIS2.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................
Page 25 of 873
GENERAL SPECIFICATION DATA
7
INFORMATION SHIFT SPEED AUTOMATIC ZF ON 3.9 V8i
OPERATION SELECTOR VEHICLE SPEED ENGINE SPEED
POSITON APPROX APPROX (RPM)
KICKDOWN
MPH KPH
KD4 - 3 D 84 - 92 136 - 150
KD3 - 2 3(D) 57 - 62 91 - 99
KD2 - 1 2(D,3) 27 - 34 44 - 56
KD3 - 4 D N/A N/A
KD2 - 3 D(3) 60 - 63 96 - 104 4750 - 5200
KD1 - 2 D(3,2) 34 - 40 56 - 64 4600 - 5250
FULL THROTTLE
FT4 - 3 D 61 - 67 98 - 108
FT3 - 2 3(D) 40 - 46 64 - 73
FT3 - 4 D 74 - 80 119 - 129 3980 - 4330
FT2 - 3 D(3) 55 - 60 88 - 96 4350 - 4800
FT1 - 2 D(3,2) 29 - 34 48 - 56 3950 - 4650
PART THROTTLE
PT4 - 3 D 47 - 54 75 - 86
PT3 - 2 D(3) 29 - 37 48 - 59
PT2 - 1 D(3,2) 10 - 12 16 - 19
LIGHT THROTTLE
LT3 - 4 D 26 - 30 43 - 49 1430 - 1650
LT2 - 3 D(3) 18 - 22 29 - 35 1420 - 1820
LT1 - 2 D(3,2) 9 - 10 14 - 16 1180 - 1220
ZERO THROTTLE
ZT4 - 3 D 19 - 25 31 - 41
ZT3 - 2 D(3) 12 - 15 19 - 24
ZT2 - 1 D(3,2) 6 - 7 10 - 11
TORQUE CONVERTER
Lock up (IN) D 51 - 54 81 - 86 1875 - 2000
Unlock (OUT) D 49 - 52 78 - 83 1825 - 1930
NOTE: The speeds given in the above chart are approximate and only intended as a guide. Maximum shift
changes should take place within these tolerance parameters.
Page 26 of 873
04GENERAL SPECIFICATION DATA
8
INFORMATION SHIFT SPEED AUTOMATIC ZF ON Tdi ENGINE
OPERATION SELECTOR VEHICLE SPEED ENGINE SPEED
POSITON APPROX APPROX (RPM)
KICKDOWN
MPH KPH
KD4 - 3 D 62 - 72 99 - 115
KD3 - 2 3(D) 43 - 49 69 - 78
KD2 - 1 2(D,3) 23 - 36 37 - 58
KD3 - 4 D 64 - 76 102 - 122 3400 - 4000
KD2 - 3 D(3) 46 - 51 74 - 82 3600 - 3900
KD1 - 2 D(3,2) 26 - 29 42 - 46 3500 - 3800
PART THROTTLE
PT4 - 3 D 39 - 45 62 - 72
PT3 - 2 D(3) 24 - 30 38 - 48
PT2 - 1 D(3,2) 18 - 20 29 - 32
LIGHT THROTTLE
LT3 - 4 D 24 - 28 38 - 45 1300 - 1400
LT2 - 3 D(3) 21 - 23 34 - 37 1700 - 1800
LT1 - 2 D(3,2) 13 - 14 21 - 22 1700 - 1900
ZERO THROTTLE
ZT4 - 3 D 22 - 27 35 - 43
ZT3 - 2 D(3) 18 - 22 29 - 35
ZT2 - 1 D(3,2) 9 - 11 14 - 18
TORQUE CONVERTER
Lock up (IN) D 46 - 49 74 - 78 1600 - 1850
Unlock (OUT) D 45 - 48 72 - 77 1700 - 1800
NOTE: The speeds given in the above chart are approximate and only intended as a guide. Maximum shift
changes should take place within these tolerance parameters.
Page 27 of 873
GENERAL SPECIFICATION DATA
9
INFORMATION TRANSMISSION 3.9 V8i
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Clutch
Make and type Borg and beck diaphram type..................................................................
Clutch plate diameter 266.5mm........................................................
Automatic gearbox
Type ZF4HP Four speed and reverse with fluid torque converter.....................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output, front....................................................................
and rear drive permanently engaged via a lockable
differential.
Propeller shafts
Type
Front Tubular 51mm diameter.................................................................................
Front - Catalyst vehicles Solid bar 28.6mm diameter...................................................
Rear Tubular 51mm diameter.................................................................................
Universal joints Open type Hookes O3EHD.................................................................
Rear axle
Type Spiral bevel, fully floating shafts.................................................................................
Ratio 3.54:1.................................................................................
Front axle
Type Spiral bevel, enclosed constant velocity joints, fully.................................................................................
floating shafts
Angularity of universal joint on full lock 32° ............................
Ratio 3.54:1.................................................................................
Page 28 of 873
04GENERAL SPECIFICATION DATA
10
INFORMATION COOLING SYSTEM 3.9 V8i
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti-freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler.
Fan and viscous coupling assembly 11 blade axial flow 433mm diameter.................................
Pump type Centifugal, impellor, belt driven.........................................................................
Thermostat opening 88 degrees..........................................................
Expansion tank cap pressure 15 p.s.i. (system pressure)............................................
STEERING
Power steering box
Make/type Adwest Varamatic - worm and roller box........................................................................
Ratio Variable: straight ahead 19.3:1 on lock 14.3:1.................................................................................
Steering wheel turns, lock-to-lock 3.375....................................
Steering pump
Make/type -V8i ZF - Unicorn.................................................................
Make/type - Mpi & Tdi Hobourn-Eaton series 500......................................................
Steering geometry
Steering wheel diameter 405mm..................................................
Steering wheel diameter airbag model 400mm.............................
Toe-out measurement 0 to 2mm toe out......................................................
Toe-out included angle 0Ê to 0Ê 16'.....................................................
Camber angle 0Ê.................................................................. Check with vehicle in static..............
unladen condition, that is, vehicle
with water,
Castor angle 3Ê..................................................................... oil and five gallons of fuel. Rock..............
the vehicle up and down at the
front to allow
Swivel pin inclination static 7Ê............................................... it to take up a position..............
Page 29 of 873
GENERAL SPECIFICATION DATA
11
INFORMATION SUSPENSION
Type Coil springs controlled by telescopic dampers front.................................................................................
and rear.
Front Lateral location of axle by Panhard rod, and.................................................................................
longitudinal location by two radius arms.
Rear Lateral location of axle by a centrally positioned 'A'.................................................................................
frame bolted at the apex to a ball joint mounting.
Longitudinal location of axle by two tubular trailing
links.
ROAD SPRING DATA
V8i - Mpi
LEFT HAND DRIVE Part No Colour Code
Left hand front NRC 4306 Blue/White
Right hand front 572315 Blue
Left/Right hand rear ANR 3477 or Brown/Green
ANR 4352 Orange/Orange *
RIGHT HAND DRIVE Part No Colour Code
Left hand front 572315 Blue
Right hand front 572315 Blue
Left/Right hand rear ANR 3477 or Brown/Green
ANR 4352 Orange/Orange *
Tdi Diesel
RIGHT HAND DRIVE Part No Colour Code
Left hand front ANR 1975 or Blue/Pink/Red
ANR 4350 Brown/Brown **
Right hand front ANR 1976 or Blue/Pink/Yellow
ANR 4351 Grey/Grey **
Left/Right hand rear ANR 3477 or Brown/Green
ANR 4352 Orange/Orange *
LEFT HAND DRIVE Part No Colour Code
Left hand front ANR 1976 or Blue/Pink/Yellow
ANR 4351 Grey/Grey **
Right hand front ANR 1975 or Blue/Pink/Red
ANR 4350 Brown/Brown **
Left/Right hand rear ANR 3477 or Brown/Green
ANR 4352 Orange/Orange *
* VIN 119534 onwards
** VIN 116461 onwards
Page 30 of 873
04GENERAL SPECIFICATION DATA
12
INFORMATION SHOCK ABSORBERS
Type Telescopic, double-acting non-adjustable.................................................................................
Bore diameter 35.47mm...................................................................
BRAKES
Front service brake
Type Outboard discs with four piston calipers.................................................................................
Operation Hydraulic, servo assisted self-adjusting.........................................................................
Pad material non asbestos.....................................................................
Rear service brake
Type Outboard discs with two piston calipers.................................................................................
Operation Hydraulic, servo assisted, self-adjusting.........................................................................
Pad material non asbestos.....................................................................
Parking brake
Type Mechanical-cable operated drum brake on the rear of.................................................................................
the transfer gearbox output shaft
Lining material non asbestos..................................................................
Servo/master cylinder non ABS
Manufacturer Lucas....................................................................
Servo type LSC 115........................................................................
Master cylinder type AS/AS.........................................................
Anti-lock brake system
Manufacturer/type Wabco 4 wheel sensed add on anti-lock brake............................................................
system.
Servo/master cylinder ABS
Manufacturer Lucas....................................................................
Master cylinder type CV/CV.........................................................