door lock LAND ROVER DISCOVERY 1995 Owner's Manual

86ELECTRICAL
4
DESCRIPTION AND OPERATION BUILT IN TEST PROCEDURE
The built in test procedure is accessed as follows:
1.Starting conditions: ignition off, doors unlocked,
bonnet [hood] switch depressed.
2.Carry out instructions 3 to 7 within 8 seconds.
3.Release bonnet [hood] switch.
4.Switch ignition ON.
5.Lock doors.
6.Switch ignition OFF.
7.Switch ignition ON.
If alarm is correctly accessed, horn will sound and
LED will flash. The following checks can be made:
8.Open and close any door or tailgate - LED will
light.
9.Depress bonnet [hood] switch - hazards will
flash.
10.Check engine cranking is disabled. Do not turn
off ignition.
11.Check ultrasonic by operating handset, LED will
emit one 5 second flash, and will flash if interior
is disturbed.
NOTE: If ECU is new born mode any
handset of the right frequency will work. If
not an initialised handset is required see
Handset Initialisation.
12.Turn OFF ignition or press handset to end test
procedure. Horn will sound as before to indicate
end of test mode.

ELECTRICAL
5
DESCRIPTION AND OPERATION ANTI THEFT ALARM SYSTEM
The main function of the system is to offer easy to use
remote locking and unlocking of the vehicle without
having to actively select the alarm function.
ALARM COMPONENTS
COMPONENT LOCATION
1. Electronic control unit (ECU) and relays Passenger footwell.................
2. Bonnet switch RH engine bay..........................................................
3. Door switches
4. Alarm sounder RH engine bay.........................................................
5. Light emitting diode (LED) Dash panel.......................................
6. Ultrasonic unit Roof map pocket.........................................................
7. Lock barrel, sill buttons
8. Handset transmitter
9. Aerial 'A' post, passenger side........................................................................

86ELECTRICAL
6
DESCRIPTION AND OPERATION ALARM COMPONENT LOCATIONS (96 MODELS)
COMPONENT LOCATION
1. Electronic control unit (ECU) and relays Under dash (passenger side).................
2. Anti-theft alarm indicator light Instrument panel..................................
3. Engine immobilisation warning light (EIWL) * Instrument panel..........
4. Passive coil Over starter switch barrel.............................................................
5. Bonnet switch RH engine compartment..........................................................
6. Door switches
7. Ultrasonic sensor Interior light switch panel....................................................
8. Lock barrel, sill buttons
9. Handset and key
10. Battery backed-up sounder or horn * RH engine compartment......................
11. Immobilisation unit (spider) * Above heater...................................
12. Aerial Part of fascia harness.......................................................................
* where applicable

ELECTRICAL
7
DESCRIPTION AND OPERATION ANTI-THEFT ALARM DESCRIPTION (96 MODELS)
NOTE: The alarm system provides security
protection under wide ranging
circumstances and is fully programmable
to meet market requirements; consequently some
of the features listed will vary dependent on
vehicle model or territory.
The handset is intended to be the primary source of
control for the alarm system. The key should only be
used in the event of handset failure or if perimetric
arming only is required.
Immobilisation
After a time period the vehicle is automatically
immobilised regardless of whether or not the alarm is
armed.
Mobilisation
The handset provides the normal means of
mobilisation. In the event of handset failure, the key
may be used to enter the emergency key access
code.
Perimetric arming
Provides protection whilst the vehicle is still occupied.
Volumetric arming
If movement within the vehicle is detected the alarm
will be triggered.
NOTE: Perimetric arming always
accompanies volumetric arming.
Built-in test
The alarm system has a built-in test procedure, but if
possible any fault finding should normally be
undertaken using TestBook.
Emergency key access (EKA)
In the event of handset failure the alarm can be
disarmed by entry of the EKA code which is unique to
each vehicle.CONTROL SYSTEM
Electronic control unit (ECU) and relays
The ECU is the alarm system 'brain' and controls all
alarm functions. It responds to inputs received, by
supplying suitable outputs to indicate the status of the
alarm system or activating the relevant warning
devices.
Handset
The handset is the primary source of control for the
alarm system i.e. it locks and unlocks the vehicle,
arms and disarms the alarm.
Door key
The vehicle may be locked using the key (perimetric
arming only).
NOTE: The vehicle MUST be unlocked
using the handset. The key may be used to
unlock the vehicle if the handset fails to
operate, see operation, Emergency key access.
Passive coil
The passive coil is located around the starter switch
and triggers the handset (usually located on the
keyring) if it is within close proximity.
Aerial
The aerial is a floating connection which supplies the
alarm ECU with the signal received from the handset.
Immobilisation unit (spider)
Dependent on model or territory, the system may be
fitted with an immobilisation unit which is discreetly
located and provides an interface between the ECU
and immobilised areas of the vehicle.

86ELECTRICAL
8
DESCRIPTION AND OPERATION DETECTION COMPONENTS
Switches
Perimetric protection for the vehicle is provided by
ECU inputs connected to the following:
Key switches (including starter)
Sill buttons
Bonnet switch
Door switches
Ultrasonic sensor
The ultrasonic sensor is located on the interior light
switch panel and triggers the alarm if movement is
detected.
WARNING INDICATORS
Battery backed-up sounder
The battery backed-up sounder is located in the
engine compartment and provides an audible warning
whenever the alarm is triggered.
NOTE: Disconnecting the vehicle battery
will result in the alarm sounding if the
correct procedure has not been followed.
See Repair, Battery.
Engine immobilisation warning light (EIWL)
The engine immobilisation warning light is located in
the instrument pack and provides a visual indication
that the engine is immobilised.
Anti-theft alarm indicator light
The anti-theft alarm indicator light is located in the
instrument pack and provides a visual indication of the
alarm status.
Inertia switch and central door locking
As a safety feature, the alarm system is designed to
recognise the inertia switch and via the ECU, unlock
the doors in the event of a collision.
NOTE: This feature only applies when the
starter switch is in the on position.ANTI-THEFT ALARM OPERATION (96 MODELS)
Full arming and immobilisation
Locking the vehicle using the handset immobilises the
engine and initializes both volumetric and perimetric
protection, providing:
1.After a lock signal has been received, a period of
15 seconds has elapsed during which no
movement is detected inside the vehicle;
2.No door or bonnet is open.
NOTE: If either of the above conditions are
not satisfied, the alarm will only be
partially armed. This is a mislock condition
which will be made apparent by a delay of 10
seconds before the anti-theft alarm indicator
begins to flash.
Disarming the alarm
NOTE: ALWAYS disarm the alarm using
the handset.
Unlocking with the key will not disarm the alarm or
mobilise the vehicle. If the handset fails to unlock the
vehicle
See Repair, Handset.
Partial arming and immobilisation
The alarm will be partially armed and the engine
immobilised if the vehicle is locked with the handset or
key, if:
1.After a lock signal has been received, a period of
15 seconds has elapsed during which movement
is detected inside the vehicle;
2.A door or bonnet is open.
NOTE: This is a mislock condition which
will be made apparent by a delay of 10
seconds before the anti-theft alarm
indicator begins to flash. Subsequent closure of
the offending aperture will cause the alarm to
attempt full arming as previously described.
Immobilisation
The vehicle will be automatically immobilised
whenever any of the following conditions occur:
1.The vehicle is locked using the handset.
2.The vehicle is locked using the key.
3.Thirty seconds after the starter switch has been
turned off AND the driver's door opened.
4.Five minutes after the starter switch is turned off
or the alarm disarmed.

ELECTRICAL
9
DESCRIPTION AND OPERATION Mobilisation
The vehicle can be mobilised using any one of the
following processes:
1.Placing the handset in close proximity to the
starter switch with the starter switch turned on
(normally achieved by placing the key in the
starter switch, providing the key and handset are
attached).
NOTE: Under normal circumstances the
remobilisation of the vehicle will not be
apparent.
2.Pressing unlock button on handset.
3.Pressing lock button on handset with starter
switch turned on.
4.Entry of EKA code using the key.
NOTE: Any attempt to start the vehicle
using the key (detached from the handset)
will be unsuccessful. Use one of the above
methods.
See Warning indicators.
Volumetric protection
When the vehicle is locked using the handset both
perimetric and volumetric protection are activated
providing there is no mislock condition.
Perimetric protection
The vehicle is always perimetrically protected when
the alarm is armed using the handset. Perimetric
protection only, can be achieved if the vehicle is
locked using the key.
NOTE: The handset should ALWAYS be
used for unlocking the vehicle. If the
handset fails to unlock the vehicle
See
Repair, Handset.
Battery backed-up sounder (BBUS)
The sounder provides audible indication of alarm
status including:
Anti-theft warnings;
Confirmation of access to built-in test.
NOTE: Disconnecting the vehicle battery
will result in the alarm sounding if the
correct procedure has not been followed.
See Repair, Battery.
Alarm horn
The horn provides audible indication (as BBUS) of
alarm status.
NOTE: Disconnecting the vehicle battery
will have no effect on the horn.
Engine immobilisation warning light (EIWL)
NOTE: Under normal circumstances the
light will not illuminate.
The light will only illuminate (after 2 seconds) if the
handset is detached from the key (or the handset
fails) and an attempt is made to start the vehicle.
Anti-theft alarm indicator light
The light flashes to indicate the alarm status.
If the alarm system is fully armed, the light will flash
rapidly for 10 seconds and then settle to the slow
(anti-theft deterrent) flash.
If the alarm system is perimetrically armed, the light
will intermittently flash rapidly for 10 seconds and then
settle to the slow (anti-theft deterrent) flash.
If the alarm system is partially armed, the light will
NOT emit the slow flash until 10 seconds after arming
(to allow the cause to be investigated).
If the vehicle has been left unlocked, providing the
driver's door is closed, the light will flash slowly
indicating immobilisation. If the driver's door is open,
the light will remain illuminated.
Emergency key access (EKA)
The emergency key access code should be entered in
accordance with the instructions in the Owner's
Handbook.

86ELECTRICAL
10
DESCRIPTION AND OPERATION Radio frequency system
The RF system uses frequencies according to market
and both ECU and handset are colour coded:
Territory ECU/Handset............................... Frequency..................
Europe Blue/Blue.................................. 433.92 MHz.........................
NAS Green/Green....................................... 315.00 MHz....................
Japan Green/Green.................................... 315.00 MHz....................
Gulf Green/Green....................................... 315.00 MHz....................
Rest of World Green/Brown........................ 315.00 MHz...................
NOTE: In service NAS, Japan and Gulf will
have the handset changed to brown.
Passive coil
The passive coil excites a receiving coil in the handset
causing it to automatically transmit a remobilisation
signal to the ECU.
Inertia switch and central door locking
Actuation of the inertia switch will cause the doors to
be unlocked. A time-out period (programmable
between 0-5 minutes) will ensue, during which all CDL
and alarm activity is disabled.
NOTE: This feature only applies when the
starter switch is in the on position.
Handset
Under normal circumstances pressing the respective
buttons on the handset once, will unlock or lock the
vehicle. If operating the handset does not achieve the
desired effect
See Repair, Handset.
Functional detail
For full functional details and circuit diagrams
See
Electrical Trouble Shooting Manual..
Vehicle traceability
All Land Rover vehicles are fitted with a multitude of
discreet security features to prevent theft or assist
recovery in the event of a vehicle being stolen. All
vehicles are traceable, since it is impossible to
remove all security identification.

ELECTRICAL
11
DESCRIPTION AND OPERATION ANTI-THEFT ALARM BUILT-IN TEST (96 MODELS)
NOTE: The handset should be detached
from the key to allow perimetric testing of
the alarm system. The system will
automatically switch to volumetric testing if the
handset is in close proximity to the starter switch.
The built-in test procedure can be accessed providing
the following conditions exist:
Alarm disarmed.
Ignition off.
Doors unlocked.
Bonnet[hood] closed.
The test mode can be entered by completing the
following instructions within 5 seconds:
1.Open bonnet.
2.Turn starter switch on.
3.Open driver's door (far enough to activate
switch).
4.Turn starter switch off.
5.Turn starter switch on.
If the test mode has been correctly accessed, the
sounder/horn will operate briefly and the anti-theft
alarm indicator and hazard warning lights will flash.
Perimetric tests
The anti-theft alarm indicator light and the hazard
warning lights will flash when:
1.Door switches are activated;
2.The bonnet is opened;
3.Sill switches are activated;
4.Key switches are activated.
NOTE: Operation of key switches can be
verified by turning the key in the relevent
direction so as not to simultaneously
activate the sill switch. If the key switch changes
state, the change should be detected but the sill
switch will not be activated.
Volumetric tests
Press the unlock button or move the handset close to
the starter switch to disable perimetric testing and
enable volumetric testing. If movement is detected
within the vehicle by the ultrasonic sensor it will be
indicated by flashing the anti-theft alarm indicator and
hazard warning lights.
NOTE: Exit anti-theft alarm built-in test by
turning starter switch to the off position.

ELECTRICAL
1
REPAIR FUSE BOX - INTERIOR
Right Hand Drive shown
The interior fusebox is fitted below the steering column, behind the trim panel. It comprises of three integral units.
'A'Main fusebox,'B'Satellite 2,'C'Satellite 1.
A label in the fusebox cover shows the circuits protected, the fuse rating and their locations. Access is by
releasing the fixing screws and lowering the panel.
'A' Main fusebox
1. Stop lights, direction indicators
2. LH side light
3. Radio/cassette/CD player
4. RH headlight main beam
5. LH headlight main beam
6. Cigar lighter
7. Airbag SRS
8. RH side lights
9. Rear fog guard lights
10. RH headlight dipped beam
11. LH headlight dipped beam
12. Multi-function unit
13. Ignition feed for Multi-function unit
14. Instruments, reversing lights
15. Air conditioning, windows
16. Washers & wipers - front
17. Starter, glow plug
18. Wash/wipe - rear, mirrors, cruise control
'B' Satellite 2
1. Electric windows - front
2. Electric windows - rear
3. Anti-lock braking
4. Central door locking
5. Electric sun roof
6. Trailer lights
'C' Satellite 1
1. Anti-theft alarm
2. Headlight washers
3. Engine management
4. Anti-lock brakes
5. Anti-theft alarm
6. Rear air conditioning, heater
'D' Spare fuses (5 off)

86ELECTRICAL
2
REPAIR FUSE BOX - ENGINE COMPARTMENT
The fusebox is located on the right side of the engine compartment. The circuits protected and their locations are
shown on the inside of the fusebox cover. To change a main circuit fuse prise off protective cover A and remove
retaining screws.
Fuses
1. Heated rear window
2. Sidelights
3. Air conditioning
4. Hazard warning lights, horn
5. ABS valve
6. Fuel pump
7. Fuel injectors
A Main circuit fuses
8. ABS pump
9. Ignition circuits
10. Lighting
11. Window lift, central door locking, rear blower
12. Heater, air conditioning
13. Generator