battery LAND ROVER FREELANDER 2001 Workshop Manual

AUTOMATIC GEARBOX - JATCO
REPAIRS 44-23
23.Fit CKP sensor, fit bolt and tighten to 9 Nm (7
lbf.ft).
24.Position fluid cooler, tighten M12 bolts to 85 Nm
(63 lbf.ft) and M8 bolt to 25 Nm (18 lbf.ft).
25.Clean fluid cooler unions.
26.Lubricate new 'O' rings with clean transmission
fluid and fit 'O' rings to fluid cooler hoses.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
27.Connect fluid cooler hoses to gearbox and
tighten unions to 18 Nm (13 lbf.ft).
28.Clean exhaust manifold and mating face on
cylinder head.
29.Fit exhaust manifold gasket.
30.Position exhaust manifold, fit nuts and
progressively tighten, from centre outwards to
45 Nm (33 lbf.ft).
31.Connect HO2S multiplug and secure to support
bracket.
32.Position IRD cooling hose retainer, fit bolt and
tighten to 25 Nm (18 lbf.ft).
33.Align marks on drive plate to torque converter.
34.Fit bolts securing drive plate to torque converter
and tighten bolts to 45 Nm (33 lbf.ft).
35.Clean torque converter access plate.
36.Position access plate, fit bolts and tighten to 9
Nm (7 lbf.ft).
37.Clean end of drive shaft and mating splines in
gearbox.
38.Fit new circlip to LH drive shaft.
39.With assistance pull hub outwards, align drive
shaft and fit to gearbox, taking care not to
damage drive shaft oil seal.
CAUTION: Pull the drive shaft to ensure the
circlip is fully engaged and retains the shaft.
40.Fit splash shield and secure with bolts.
41.Position trunnion to selector lever, locate inner
cable through trunnion, do not tighten nut at this
stage.
42.Position selector cable to gearbox bracket and
secure with clip.
43.Adjust selector cable.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Selector cable - adjust.
44.Fit IRD.

+ INTERMEDIATE REDUCTION
DRIVE, REPAIRS, Intermediate reduction
drive (IRD) unit - KV6.
45.Connect battery earth lead.
46.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
47.Untie and close bonnet.
Gearbox - Td4
$% 44.20.02.99
Remove
1.Disconnect battery earth lead.
2.Tie bonnet back in upright position.
3.Remove intake ducting assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
4.Remove fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - Td4.
5.Remove starter motor.

+ CHARGING AND STARTING,
REPAIRS, Starter motor - Td4.
6.Remove IRD.

+ INTERMEDIATE REDUCTION
DRIVE, REPAIRS, Intermediate reduction
drive (IRD) unit - Td4.
7.Secure LRT-54-026 to drive shaft inboard joint.
Using a suitable lever, release inboard joint
from gearbox.
8.With assistance, pull hub outwards and remove
LH drive shaft from gearbox.
CAUTION: Pull the drive shaft horizontally
to avoid damaging the differential oil seal.

AUTOMATIC GEARBOX - JATCO
REPAIRS 44-27
21.Fit new circlip to LH drive shaft.
22.With assistance, fit LH drive shaft to gearbox,
keep shaft square to prevent damage to oil seal
in gearbox.
23.Fit IRD.

+ INTERMEDIATE REDUCTION
DRIVE, REPAIRS, Intermediate reduction
drive (IRD) unit - Td4.
24.Fit starter motor.

+ CHARGING AND STARTING,
REPAIRS, Starter motor - Td4.
25.Fit fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - Td4.
26.Fit intake ducting assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
27.Connect battery earth lead.
28.Untie and close bonnet.
Fluid pan - reseal
$% 44.24.05
Remove
1.Drain gearbox fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
2.Remove fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - KV6.
3.Release multiplugs from clips attached to fluid
pan.
4.Remove 21 bolts securing fluid pan to gearbox.
5.Remove fluid pan.
Refit
1.Clean fluid pan and mating face on gearbox.
2.Apply sealant, Part No. STC 4600to contact
faces of fluid pan and gearbox.
3.Position fluid pan, fit bolts and tighten
progressively to 7 Nm (5 lbf.ft).
4.Secure multiplugs to clips.
5.Fit fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - KV6.
6.Fill gearbox with fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.

AUTOMATIC GEARBOX - JATCO
44-28 REPAIRS
Fluid cooler - air blast - Td4 (hot
climates)
$% 44.24.09
Remove
1.Disconnect battery earth lead.
2.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
3.Remove combined fan and thermostat
multiplug from harness.
4.Remove harness multiplug from mounting
bracket.
5.Remove nut securing multiplug mounting
bracket, move bracket aside.
6.Position container beneath gearbox cooler
hoses to contain fluid spillage.7.Disconnect cooler quick release hoses.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
8.Remove 3 bolts securing air blast cooler
assembly to chassis and move aside.
M37 1754

AUTOMATIC GEARBOX - JATCO
REPAIRS 44-29
9.Remove 2 scrivets, release cooler ducting from
hooks and move aside.
10.Remove 5 bolts securing fan cowl to cooler
matrix and move aside.
11.Remove 4 nuts securing fan motor to cowl and
move aside.
NOTE: Do not carry out further dismantling if
component is removed for access only.12.Remove cooler pipe union nuts and move pipes
aside.
CAUTION: To prevent damage to
components, use two spanners when
loosening or tightening unions.
13.Remove and discard 'O' rings.
Refit
1.Fit new 'O' rings to oil cooler pipes.
2.Fit pipes to cooler matrix, align and tighten
union nuts to 25 Nm (18 lbf.ft).
3.Position fan cowl to cooler matrix, fit bolts and
tighten to 5 Nm (3.5 lbf.ft).
4.Position fan motor to cowl, fit nuts and tighten
to 5 Nm (3.5 lbf.ft).
5.Fit cooler duct and secure with scrivets.
6.Fit air blast cooler assembly, fit bolts and
tighten upper bolt to 5 Nm (3.5 lbf.ft). Lower
bolts should be tightened to 10 Nm (7.5 lbf.ft).
7.Ensure connections are clean, then fit and
secure flexible hoses.
8.Fit multiplug mounting bracket and tighten nut
to 10 Nm (7.5 lbf.ft).
9.Connect harness multiplug, fit multiplug to
mounting bracket.
10.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
11.Connect battery earth lead.

AUTOMATIC GEARBOX - JATCO
44-30 REPAIRS
Fluid cooler - Td4
$% 44.24.10
Remove
1.Disconnect battery earth lead.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Position container to collect coolant spillage.
4.Release 2 clips and disconnect coolant hoses
from fluid cooler.
5.Position container to collect fluid spillage.
6.Disconnect 2 fluid cooler hose unions and
discard 'O' rings.
7.Remove 3 bolts securing fluid cooler bracket.
8.Remove fluid cooler.Refit
1.Clean cooler mounting points.
2.Position fluid cooler to mounting, fit bolts,
tighten 2 bolts to 45 Nm (33 lbf.ft) and
remaining bolt to 25 Nm (18 lbf.ft).
3.Connect coolant hoses and secure with clips.
4.Lubricate new 'O' rings with clean transmission
fluid and fit to fluid cooler hoses.
5.Connect hoses to fluid cooler and tighten
unions to 18 Nm (13 lbf.ft).
6.Top-up gearbox fluid level.

+ MAINTENANCE, MAINTENANCE,
Automatic Gearbox – JATCO.
7.Connect battery earth lead.
8.Refill cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
9.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.

DRIVESHAFTS
REPAIRS 47-1
DRIV ESHAFTS REPAIRS
Shaft with both joints - LH
$% 47.10.01
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Remove 3 bolts and remove splash shield.
6.Release stake from drive shaft nut.
7.With assistant depressing the brake pedal,
remove and discard the drive shaft nut.8.Remove clip securing brake hose and release
hose from damper bracket.
9.Release ABS sensor harness and brake hose
from damper.
10.Release ABS sensor from hub.
11.Remove 2 bolts securing brake caliper to hub.
Release caliper from hub and tie aside.
CAUTION: Do not allow caliper to hang on
brake hose.

DRIVESHAFTS
47-2 REPAIRS
12.Remove 2 bolts securing damper to hub.
13.Release hub from damper.
14.Release drive shaft from hub.
15.Position container to catch oil spillage
16.Secure LRT-54-026 to drive shaft inboard joint.
Using a lever, release drive shaft from gearbox.
17.Remove drive shaft.
CAUTION: Care must be taken not to
damage oil seal when removing drive shaft
from gearbox
18.Remove and discard circlip from drive shaft.Refit
1.Inspect gearbox seal for signs of wear or
damage.
2.Wipe drive shaft ends, gearbox oil seal and
hub.
3.Lubricate oil seal running surfaces.
4.Fit new circlip to drive shaft.
5.Fit drive shaft ensuring circlip is fully engaged.
CAUTION: Drive shaft must be fitted with
care to prevent damage to gearbox oil seal.
6.Position drive shaft in hub.
7.Fit new hub nut but do not tighten at this stage.
8.Fit hub to damper, fit nuts and bolts and tighten
to 205 Nm (150 lbf.ft).
9.Position caliper to brake disc fit bolts and
tighten to 100 Nm (74 lbf.ft).
10.Clean ABS sensor and mating face.
11.Lubricate ABS sensor with anti-seize grease.
12.Fit ABS sensor .
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
reluctor ring.
13.Position ABS harness and brake hose in
bracket and secure with clip.
14.Fit splash shield and secure with bolts.
15.Tighten front hub nut to 400 Nm (295 lbf.ft).
16.Stake front hub nut.
17.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
18.Check and top up oil level as required.

+ MAINTENANCE, MAINTENANCE,
Manual Gearbox – PG1.

+ MAINTENANCE, MAINTENANCE,
Manual Gearbox – GETRAG.

+ MAINTENANCE, MAINTENANCE,
Automatic Gearbox – JATCO.
19.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
20.Remove stands and lower vehicle.
21.Connect battery earth lead.

DRIVESHAFTS
REPAIRS 47-3
Shaft with both joints - RH
$% 47.10.02
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Remove 3 bolts securing RH splash shield to
body and remove shield.
6.Release stake from drive shaft nut.
7.With assistant depressing the brake pedal,
remove and discard the drive shaft nut.8.Remove clip securing brake hose and release
hose from damper bracket.
9.Release ABS sensor harness and brake hose
from damper.
10.Release ABS sensor from hub.
11.Remove 2 bolts securing brake caliper to hub.
Release caliper from hub and tie aside.
CAUTION: Do not allow caliper to hang on
brake hose.

DRIVESHAFTS
47-4 REPAIRS
12.Remove 2 bolts securing damper to hub.
13.Release hub from damper.
14.Release drive shaft from hub.
15.Position container to catch oil spillage.
16.Secure LRT-54-026 to drive shaft inboard joint.
Using a lever, release drive shaft from gearbox.
17.Remove drive shaft.
CAUTION: Care must be taken not to
damage oil seal when removing drive shaft
from gearbox18.Remove and discard circlip from drive shaft.
Refit
1.Inspect gearbox seal for signs of wear or
damage.
2.Wipe drive shaft ends, gearbox oil seal and
hub.
3.Lubricate oil seal running surfaces.
4.Fit new circlip to drive shaft.
5.Fit drive shaft ensuring circlip is fully engaged.
CAUTION: Drive shaft must be fitted with
care to prevent damage to gearbox oil seal.
6.Position drive shaft in hub.
7.Fit new hub nut but do not tighten at this stage.
8.Fit hub to damper, fit nuts and bolts and tighten
to 205 Nm (150 lbf.ft).
9.Position caliper to brake disc fit bolts and
tighten to 100 Nm (74 lbf.ft).
10.Clean ABS sensor and mating face.
11.Lubricate ABS sensor with anti-seize grease.
12.Fit ABS sensor .
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
reluctor ring.
13.Position ABS harness and brake hose in
bracket and secure with clip.
14.Fit splash shield and secure with bolts.
15.Tighten front hub nut to 400 Nm (295 lbf.ft).
16.Stake front hub nut.
17.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
18.Check and top up oil level as required.

+ MAINTENANCE, MAINTENANCE,
Intermediate Reduction Drive - Non NAS
models.
19.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
20.Remove stands and lower vehicle.
21.Connect battery earth lead.

DRIVESHAFTS
REPAIRS 47-5
Gaiter - bell & joint - outer - front
$% 47.10.03
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove drive shaft outer joint.

+ DRIVESHAFTS, REPAIRS, Bell &
joint - outer - LH - front.
5.Slide gaiter from shaft.
Refit
1.Clean drive shaft.
2.Fit new gaiter to shaft.
3.Fit drive shaft outer joint.

+ DRIVESHAFTS, REPAIRS, Bell &
joint - outer - LH - front.
4.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
5.Remove stands and lower vehicle.
6.Connect battery earth lead.
Bell & joint - outer - LH - front
$% 47.10.04
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove drive shaft.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - LH.
5.Place drive shaft in vice.
6.Release both gaiter clips and discard.
7.Slide gaiter along shaft to gain access to outer
joint.
8.Using a drift against the inner part of the joint,
remove joint from shaft.
9.Inspect gaiter for damage and renew if
necessary.
Refit
1.Clean drive shaft and gaiter.
2.Fit new circlip to drive shaft.
3.Position outer joint to shaft, use a screwdriver
to press circlip into its groove and push joint
fully onto shaft.
4.Apply grease from the sachet to the joint.
5.Position gaiter to joint and use a 'Band-it
thriftool' LRT-99-019 to secure the 2 new clips.
6.Fit drive shaft.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - LH.
7.Fit front road wheels, fit and tighten nuts to 115
Nm (85 lbf.ft).
8.Remove stands and lower vehicle.
9.Connect battery earth lead.