sunroof LAND ROVER FREELANDER 2001 User Guide

SUNROOF
76-6-8 REPAIRS
Drain tube - sun/sliding roof - front - each
- 5 door
$% 76.84.20
Remove
1.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
2.Remove scrivet and 5 Torx screws securing
front carpet retainer and remove carpet
retainer.
3.Release drain tube from wheel arch grommet.
4.Disconnect drain tube from sun roof and
discard cable tie.
5.Attach draw string and remove drain tube.Refit
1.Attach draw string to drain tube and pull into
position.
2.Connect drain tube to sun roof and secure with
new cable tie.
3.Connect drain tube to wheel arch grommet.
4.Secure wheel arch grommet.
5.Fit carpet retainer and secure with Torx screws
and scrivet.
6.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.

SUNROOF
REPAIRS 76-6-9
Drain tube - sun/sliding roof - rear - each
- 5 door
$% 76.84.21
Remove
1.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
2.Release drain tube from wheel arch grommet
and 3 securing clips.
3.Disconnect drain tube from sun roof and
discard cable tie.
4.Remove drain tube.
Refit
1.Position drain tube.
2.Connect drain tube to sun roof and secure with
new cable tie.
3.Connect drain tube to wheel arch grommet and
secure in clips.
4.Secure wheel arch grommet.
5.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
Finisher - flange to headlining - front
$% 76.84.25
Remove
1.Release sun roof surround finisher from sun
roof aperture and remove finisher.
Refit
1.Position sun roof surround finisher and secure
in position, ensure locating lug is in position at
the front of finisher.

SUNROOF
76-6-10 REPAIRS
Wind deflector - sun/sliding roof - 5 door
$% 76.84.28
Remove
1.Open sun roof.
2.Carefully release wind deflector retaining pegs
from roof.
3.Release wind deflector from lifting assemblies.
4.Remove wind deflector.
Refit
1.Position wind deflector to lifting assemblies and
secure in position.
2.Carefully locate retaining pegs under roof.
3.Close sun roof.
Sun blind - front - one - 5 door
$% 76.84.30
Remove
1.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
2.Remove 2 blind stops.
3.Remove 2 rubber buffers.
4.Slide blind to the rear of sun roof and remove
from guides.
Refit
1.Lubricate guides with isoflex grease.
2.Fit blind to guides and slide into position.
3.Fit blind stops and rubber buffers.
4.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.

SUNROOF
REPAIRS 76-6-11
Switch - sun/sliding roof - front
$% 76.84.40
Remove
1.Release switch from front console.
2.Disconnect multiplug and remove switch.
Refit
1.Position switch and connect multiplug.
2.Fit switch to front console.
Seal - tray - sun /sliding roof - front - 5
door
$% 76.84.61
Remove
1.Remove sun roof assembly.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 5 door.
2.Remove sun roof tray seal.
Refit
1.Clean old adhesive from tray.
2.Remove backing from new seal and fit seal to
tray.
3.Fit sun roof assembly.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 5 door.

PANEL REPAIRS
77-2-12 REPLACEMENT PANELS
Roof assembly - 5 door
1Roof assembly (with sunroof)
2Roof assembly (without sunroof)

PANEL REPAIRS
REPAIRS 77-2-61
Front roof assembly - 3 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove LH and RH front roof panel finishers.
5.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
6.Remove sunroof assembly.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
7.Remove windscreen.

+ SCREENS, REPAIRS, Windscreen.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. There are
no plug welds used in this procedure, spot
welds only.
Refit
1.Fit windscreen.

+ SCREENS, REPAIRS, Windscreen.
2.Fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
3.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
4.Fit LH and RH front roof panel finishers.
5.Connect all ECUs.
6.Connect alternator.
7.Connect battery earth lead.
Rear roof assembly - 3 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove soft/hard top.
5.Remove LH and RH rear roof panel finishers.
6.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
7.Remove sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
8.Remove aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 3 door.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. There are
no plug welds used in this procedure, spot
welds only.
Refit
1.Fit aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 3 door.
2.Fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 3 door.
3.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
4.Fit LH and RH rear roof panel finishers.
5.Fit soft/hard top.
6.Connect all ECUs.
7.Connect alternator.
8.Connect battery earth lead.

Roof assembly - 5 door
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove tail door glass upper finisher.
5.Remove LH and RH roof panel finishers.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
6.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
7.If applicable, remove sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 5 door.
8.Remove aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 5 door.
9.Remove windscreen.

+ SCREENS, REPAIRS, Windscreen.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1.Fit windscreen.

+ SCREENS, REPAIRS, Windscreen.
2.Fit aerial.

+ IN CAR ENTERTAINMENT,
REPAIRS, Aerial - manual - 5 door.
3.If applicable, fit sunroof.

+ SUNROOF, REPAIRS, Sun/sliding
roof - complete - front - 5 door.
4.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
5.Fit LH and RH roof panel finishers.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
6.Fit tail door glass upper finisher.
7.Connect all ECUs.
8.Connect alternator.
9.Connect battery earth lead.

SECURITY
REPAIRS 86-4-5
Module (ECU) - volumetric - alarm
system - 5 door - without sunroof
$% 86.77.29
Remove
1.Remove LH rear quarter upper trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
2.Remove LH 'A' post upper finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
3.Release front and rear LH door seals.
4.Remove screw covers and screws from both
LH grab handles and remove grab handles.
5.Remove LH sun visor.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.6.Remove trim stud securing forward edge of
headlining.
7.Remove 2 trim studs securing centre of
headlining.

SECURITY
REPAIRS 86-4-7
Refit
1.Fit volumetric sensor and secure with screws.
2.Connect multiplug to sensor.
3.Raise headlining and secure with trim studs.
4. Up to 04MY: Position front interior lamp and
connect multiplug.
5. Up to 04MY: Fit Torx bolts securing interior
lamp and tighten to 6 Nm (4.4 lbf.ft).
6. Up to 04MY: Fit lens to front interior lamp.
7. From 04MY: Position front interior lamp and
connect multiplug.
8. From 04MY: Fit and secure front interior lamp
to headlining.
9.Position 'B/C' post upper finisher and secure
with clips.
10.Fit sun visor.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
11.Fit grab handles, tighten screws and fit screw
covers.
12.Fit 'A' post upper finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
13.Fit rear quarter upper trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
14.Secure front and rear door seals.
Module (ECU) - volumetric - alarm
system - 5 door - with sunroof
$% 86.77.29
Remove
1.Release front and rear door aperture seals.
2.Remove 'A' post upper finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
3.Remove screw covers, remove 6 screws
securing front and both rear grab handles and
remove grab handles.
4.Remove grab handle blanking plugs.