cooling LAND ROVER FREELANDER 2001 Owner's Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 2001, Model line: FREELANDER, Model: LAND ROVER FREELANDER 2001Pages: 1007, PDF Size: 23.47 MB
Page 190 of 1007
ENGINE - K SERIES KV6
REPAIRS 12-3-13
Cylinder head gasket - LH
$% 12.29.02
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
3.Remove inlet manifold chamber.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
4.Remove LH exhaust manifold gasket.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket - exhaust
manifold - LH - Non NAS.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket(s) -
exhaust manifold - LH - NAS.
5.Remove camshaft timing belt.
+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
6.Remove 4 bolts securing LH front camshaft
timing belt cover backplate to cylinder head;
remove backplate.
7.Remove LH camshaft cover gasket.
+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.8.Remove 3 nuts and 3 bolts securing ignition
coils to LH inlet manifold and release coil earth
lead, if fitted.
9.Remove ignition coils and position aside, if
fitted.
10.Release clip and disconnect coolant bleed
hose from inlet manifold and move hose aside.
11.Depress locking collar and release breather
hose from LH inlet manifold.
Page 193 of 1007
ENGINE - K SERIES KV6
12-3-16 REPAIRS
27.Position backplate, fit and tighten bolts to 9 Nm.
28.Fit camshaft timing belt.
+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
29.Fit LH exhaust manifold gasket.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket - exhaust
manifold - LH - Non NAS.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket(s) -
exhaust manifold - LH - NAS.
30.Fit inlet manifold chamber.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
31.Fill cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
32.Check engine oil level and top-up if necessary.
+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
Cylinder head gasket - RH
$% 12.29.03
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
3.Remove inlet manifold chamber.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
4.Remove RH exhaust manifold gasket.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket - exhaust
manifold - RH - Non NAS.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket(s) -
exhaust manifold - RH - KV6 - NAS.
5.Remove camshaft timing belt.
+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
6.Remove 4 bolts securing RH front timing belt
cover backplate to cylinder head and remove
backplate.
Page 196 of 1007
ENGINE - K SERIES KV6
REPAIRS 12-3-19
10.Tighten cylinder head bolts progressively in the
sequence illustrated to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 3 -Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten bolts in the same sequence a further
180°
11.Fit RH camshaft cover gasket.
+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - RH.
12.Remove and discard lower 'O' rings from
injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail; secure injector harness to protection
cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Connect coolant bleed hose to inlet manifold
and secure with clip.
19.Connect breather hoses to RH camshaft cover
and inlet manifold.
20.Position ignition coils to LH inlet manifold.
21.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
22.Connect multiplugs to plug top coils and secure
with locking clips.
23.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.
24.Position backplate, fit and tighten bolts to 9 Nm
(7 lbf.ft).25.Fit camshaft timing belt.
+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
26.Fit RH exhaust manifold gasket.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket - exhaust
manifold - RH - Non NAS.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket(s) -
exhaust manifold - RH - KV6 - NAS.
27.Fit inlet manifold chamber.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
28.Fill cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
29.Check engine oil level and top-up if necessary.
+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
Page 202 of 1007
ENGINE - K SERIES KV6
REPAIRS 12-3-25
Cover - engine acoustic
$% 12.30.50
Remove
1.Loosen clip and disconnect fresh air intake
hose from acoustic cover.
2. Non NAS: Loosen clip and release air intake
and air bypass hose from throttle body.
3. NAS:Loosen clip and disconnect air intake
hose from air flow meter (MAF) sensor.
4.Release 2 turnbuckles securing acoustic cover
to LH camshaft cover.
5.Release retaining strap and remove acoustic
cover.
Refit
1.Fit and secure engine acoustic cover.
2.Connect air intake and air bypass hoses,
secure clip.
3.Connect fresh air intake hose to acoustic cover
and tighten clip screw.
Engine and automatic gearbox - up to
03MY
$% 12.37.01.99
Remove
1.Disconnect battery earth lead.
2.Tie bonnet back in upright position.
3.Drain cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
4.Remove engine acoustic cover.
+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
5.Remove battery carrier.
+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
6.Remove engine ECM.
+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - Non NAS.
7.Remove 2 screws securing harness clamp and
remove clamp.
8.Disconnect 2 engine harness to main harness
multiplugs.
Page 211 of 1007
ENGINE - K SERIES KV6
12-3-34 REPAIRS
38.With assistant depressing the brake pedal,
tighten front hub nuts to 400 Nm (295 lbf.ft).
39.Stake nut to shaft.
40.Fit front road wheels, fit and tighten nuts to 115
Nm (85 lbf.ft).
41.Lower vehicle on ramp.
42.Connect brake servo vacuum hose to inlet
manifold chamber.
43.Connect coolant hose to underside of
expansion tank and secure with clip.
44.Connect expansion tank hose to inlet manifold
and secure clip.
45.Connect top hose to radiator and secure with
clip. Position hose in bracket.
46.Connect heater feed and return hoses and
secure with clips.
47.Connect throttle inner cable to throttle cam and
secure outer cable in abutment bracket, if fitted.
48.Secure throttle cable in clips on harness
brackets, if fitted.
49.Adjust throttle cable, if fitted.
+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
50.Connect hose to purge control valve.
51.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
52.Connect gearbox harness multiplugs and
secure multiplugs in mounting bracket clips.
53.Connect Lucar connector to starter solenoid.
54.Position earth lead to gearbox housing, fit and
tighten bolt to 25 Nm (18 lbf.ft).
55.Position engine harness to 'E' box mounting
bracket and secure with clips.
56.Connect earth header multiplug.
57.Connect multiplug to underbonnet fuse box.
58.Position battery and starter motor lead to
underbonnet fuse box, fit and tighten bolts to 8
Nm (6 lbf.ft).
59.Fit underbonnet fuse box cover.
60.Position 'E' box, secure in retaining clip, fit and
tighten nut to 9 Nm (7 lbf.ft).
61.Position carrier in 'E' box and secure with clips.
62.Position and secure air duct and harness
rubber sleeve in 'E' box.
63.Connect multiplugs securing main harness to
engine harness.
64.Position ECM harness and multiplug to 'E' box,
align harness clamp and secure screws to 'E'
box.
65.Fit engine ECM.
+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - Non NAS.
66.Fit battery carrier.
+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.67.Fill cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
68.Connect battery earth lead.
69.Fill gearbox with fluid.
+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
70.Fit engine acoustic cover.
+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
Page 212 of 1007
ENGINE - K SERIES KV6
REPAIRS 12-3-35
Engine and automatic gearbox - from
03MY
$% 12.37.01.99
Remove
1.Disconnect battery earth lead.
2.Tie bonnet back in upright position.
3.Drain cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
4.Remove the engine acoustic cover.
+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
5.Remove battery carrier.
+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
6.Remove engine ECM.
+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - fuel - NAS.
7.Remove bolt securing heated front screen
harness to battery positive cable.
8.Remove 2 screws securing harness clamp and
remove clamp.
9.Release multiplug from 'E' box and disconnect
body harness from engine harness.
10.Move engine harness aside.11.Disconnect multiplug from 'E' box temperature
sensor.
12.Disconnect multiplug from automatic gearbox
ECU.
13.Disconnect 'E' box cooling fan multiplug.
14.Release body harness clip from 'E' box.
15.Move body harness aside.
16.Release air duct from 'E' box.
M00 0000M12 8001
Page 221 of 1007
ENGINE - K SERIES KV6
12-3-44 REPAIRS
35.Fit rear beam.
+ FRONT SUSPENSION, REPAIRS,
Rear beam.
36.Fill IRD to correct level with fluid.
+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) lubrication system -
drain & refill - NAS.
37.Fit exhaust front pipe.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - NAS.
38.With assistant depressing the brake pedal,
tighten front hub nuts to 400 Nm.
39.Stake nuts to drive shafts
40.Fit front road wheels, fit and tighten nuts to 115
Nm.
41.Lower vehicle on lift.
42.Connect brake servo vacuum hose to inlet
manifold chamber.
43.Connect coolant hose to underside of
expansion tank and secure with clip.
44.Connect expansion tank hose to inlet manifold
and secure clip.
45.Connect top hose to radiator and secure with
clip. Position hose in bracket.
46.Connect heater feed and return hoses and
secure with clips.
47.Connect throttle inner cable to throttle cam and
secure outer cable in abutment bracket.
48.Connect hose to purge valve.
49.Fit purge hose into clip.
50.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
51.Connect gearbox harness multiplugs and
secure multiplugs in mounting bracket clips.
52.Connect Lucar connector to starter solenoid.
53.Position earth lead to gearbox housing, fit and
tighten bolt to 25 Nm.
54.Position engine harness to 'E' box mounting
bracket and secure with clips.
55.Connect earth header multiplug.
56.Connect multiplug to under bonnet fuse box.
57.Position battery and starter motor lead to under
bonnet fuse box, fit and tighten bolts to 8 Nm.
58.Fit under bonnet fuse box cover.
59.Position 'E' box, secure in retaining clip, fit and
tighten nut to 9 Nm.
60.Fit carrier to 'E' box.
61.Fit air ducting to 'E' box.
62.Fit body harness to 'E' box, secure grommet
and harness clip.
63.Connect 'E' box cooling fan multiplug.
64.Connect multiplug to 'E' box temperature
sensor.
65.Connect multiplug to gearbox ECU.
66.Position engine harness to 'E' box and secure
grommet.67.Fit engine harness clamp and secure with
screws.
68.Connect engine harness multiplug to body
harness multiplug and fit multiplug to 'E' box.
69.Fit heated front screen harness to battery
positive cable and tighten bolt to 15 Nm (11
lbf.ft).
70.Fit engine ECM.
+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - fuel - NAS.
71.Fit battery carrier.
+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
72.Fill cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
73.Connect the battery earth lead.
74.Fill gearbox with fluid.
+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
75.Fit the engine acoustic cover.
+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
76.Untie and close bonnet.
Page 234 of 1007
ENGINE - K SERIES KV6
REPAIRS 12-3-57
Oil cooler - engine
$% 12.60.68
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
3.Remove RH front road wheel.
4.Remove 3 bolts securing RH splash shield to
body and remove shield.
5.Position container to collect spillage under oil
filter.
6.Loosen and remove oil cooler pipe unions from
oil filter housing, remove and discard 2 'O'
rings.
CAUTION: Failure to retain bosses will
result in damage to oil cooler. Always fit
plugs to open connections to prevent
contamination.
7.Position container to collect coolant spillage.8.Release clips and disconnect coolant hoses
from engine oil cooler.
CAUTION: Always fit plugs to open
connections to prevent contamination.
9.Remove 4 nuts securing engine oil cooler to
mounting bracket and remove oil cooler.
10.Restrain oil cooler pipe bosses on oil cooler
housing, loosen and remove oil cooler pipes
from oil cooler; remove and discard 2 'O' rings.
CAUTION: Always fit plugs to open
connections to prevent contamination.
Refit
1.Clean oil cooler pipe unions and mating faces.
2.Lubricate new 'O' rings with clean engine oil
and fit to oil cooler pipes.
3.Fit pipes to engine oil cooler, restrain bosses on
oil cooler body and tighten unions to 26 Nm (19
lbf.ft).
CAUTION: To prevent damage to
components, use two spanners when
loosening or tightening unions.
4.Position engine oil cooler to mounting bracket,
fit and tighten nuts to 25 Nm (18 lbf.ft).
5.Position oil cooler pipes to oil filter housing and
tighten unions to 26 Nm.
6.Connect coolant hoses to oil cooler and secure
with clips.
7.Fit splash shield and secure with bolts.
8.Fit RH road wheel and tighten nuts to 115 Nm
(85 lbf.ft).
9.Fill cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
10.Connect battery earth lead.
11.Check engine oil level and top-up if necessary.
M12 6614
M12 7917
Page 300 of 1007
EMISSION CONTROL
REPAIRS 17-1-9
Thermal valve - exhaust gas
recirculation (EGR) - Td4 Automatic
transmission (hot climates) - from 03 MY
$% 17.45.07
Remove
1.Disconnect the battery earth lead.
2.Release thermal valve coolant hose from clips.
3.Position container to collect coolant.
4.Release 3 clips securing coolant hoses to the
EGR thermal valve.
5.Disconnect coolant hoses from the EGR
thermal valve and remove the thermal valve.
Refit
1.Position the EGR thermal valve and connect
coolant hoses.
2.Secure hoses with clips.
3.Fit thermal valve coolant hose into clips.
4.Connect the battery earth lead.
5.Refill the cooling system.
+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
Cooler - EGR - Td4
$% 17.45.40
Remove
1.Disconnect battery earth lead.
2.Remove camshaft cover.
+ ENGINE - Td4, REPAIRS, Gasket -
camshaft cover.
3.Mark EGR pipe and cooler to aid refit.
4.Loosen clamps EGR pipes to cooler and move
clamps aside.
5.Remove pipe, EGR cooler to EGR valve.
6.Remove bolt securing fuel rails to support
bracket.
7.Remove bolt securing turbocharger outlet pipe
to support bracket.
8.Remove underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
M170364
M17 0283
Page 301 of 1007
EMISSION CONTROL
17-1-10 REPAIRS
9.Remove bolt securing turbo outlet pipe to upper
coolant rail.
10.Remove 2 bolts securing pipe support bracket
to engine lifting bracket, remove support
bracket.
11.Release clip and remove vacuum hose.
12.Remove 3 bolts securing EGR cooler to
cylinder head and lifting bracket.13.Lift EGR cooler from mounting and position a
container beneath coolant hoses.
14.Release clips and remove hoses from EGR
cooler allow coolant to drain.
15.Remove EGR cooler.
Refit
1.Position EGR cooler, connect coolant hoses
and fit clips.
2.Position EGR cooler to mounting, fit bolts and
tighten to 25 Nm (18 lbf.ft).
3.Position pipe support bracket to engine lifting
bracket, fit and tighten bolts to 25 Nm (18 lbf.ft).
4.Fit vacuum hose and tighten clip.
5.Fit bolt securing turbocharger pipe to coolant
rail and tighten to 25 Nm (18 lbf.ft).
6.Fit underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
7.Fit bolt securing turbocharger outlet pipe to
support bracket and tighten to 10 Nm (7.5
lbf.ft).
8.Fit bolt securing fuel rails to support bracket
and tighten to 10 Nm (7.5 lbf.ft).
9.Align EGR pipe to cooler fit clamp, but do not
fully tighten until camshaft cover is refitted.
10.Fit EGR pipe clamp and tighten screw.
11.Fit camshaft cover.
+ ENGINE - Td4, REPAIRS, Gasket -
camshaft cover.
12.Connect battery earth lead.
13.Top up cooling system.
+ MAINTENANCE, MAINTENANCE,
Cooling System and Intercooler.