fuel pressure LAND ROVER FREELANDER 2001 Owner's Manual

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-29
Pump - fuel
$% 19.45.08
WARNING: If fuel tank is full, using a fuel
recovery appliance, drain excess fuel from fuel
filler neck until a level below height of fuel pump
is obtained.
Remove
1.Disconnect battery earth lead.
2.Open RH rear and tail doors.
3.Fold RH rear seat forward.
4.Remove 2 fasteners securing front and rear
carpets.
5.Pull back loadspace carpet from fuel pump
access panel.
6.Remove 6 screws securing access panel.
WARNING: Depressurise the system before
disconnecting any components. Fuel
pressure will be present in the system even
if the ignition has been switched off for
some time.
7.Remove access panel.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
8.Disconnect multiplug and fuel hose from fuel
pump housing.
CAUTION: Always fit plugs to open
connections to prevent contamination.9.Use LRT-19-009 to remove locking ring from
fuel pump housing.
10.Remove fuel pump housing and discard sealing
ring.
Refit
1.Clean fuel pump housing and mating face on
fuel tank.
2.Fit new seal to fuel pump housing.
3.Fit fuel pump housing to fuel tank, fit and tighten
locking ring to 35 Nm (26 lbf.ft) using LRT-19-
009.
4.Connect multiplug and fuel hose to fuel pump
housing.
5.Fit access panel and secure with screws.
6.Position carpet and secure with fasteners.
7.Reposition rear seat.
8.Close rear and tail doors.
9.Connect battery earth lead.

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-39
Injectors - set - K1.8
$% 19.60.12
Remove
1.Disconnect battery earth lead.
2.Release clip and disconnect vacuum pipe from
fuel pressure regulator.
3.Remove engine oil dipstick.
4.Position absorbent cloth beneath fuel rail.
5.Release fuel feed hose from fuel rail.
CAUTION: Always fit plugs to open
connections to prevent contamination.6.Remove 2 bolts securing fuel rail to inlet
manifold.
7.Release fuel rail and injectors from inlet
manifold.
8.Release and remove injector spacer.
9.Disconnect multiplug from injectors.
10.Remove the fuel rail complete with injectors.
11.Release spring clips securing injectors to fuel
rail and remove fuel injectors.
12.Remove and discard 2 'O' rings from each
injector.
13.Fit protective caps to each end of injectors.

FUEL DELIVERY SYSTEM - PETROL
19-2-40 REPAIRS
Refit
1.Remove protective caps from each injector.
2.Clean injectors and recesses in fuel rail and
inlet manifold.
3.Lubricate new 'O' ring with castor oil and fit to
injector.
4.Fit injectors to fuel rail and secure with spring
clips.
5.Position fuel rail assembly and connect injector
multiplugs.
6.Fit injector spacer.
7.Push each injector into inlet manifold.
8.Fit bolts securing fuel rail to inlet manifold and
tighten to 8 Nm ( 6 lbf.ft).
9.Connect fuel feed hose to fuel rail.
10.Fit engine oil dipstick.
11.Connect vacuum pipe to fuel pressure regulator
and secure with clip.
12.Connect battery earth lead.
Actuator unit - cruise control - KV6 - non
NAS
$% 19.75.05
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Disconnect vacuum hose from actuator.
4.Remove nut securing actuator to mounting
bracket.
5.Release operating rod from throttle cam and
remove actuator.
Refit
1.Position actuator and connect operating rod to
throttle cam.
2.Position actuator into mounting bracket, fit and
tighten nut.
3.Connect vacuum hose to actuator.
4.Check pull rod to retainer clearance, with lever
fully returned, pull rod should just be held by
retainer.
5.Release retainer by turning anti-clockwise,
eliminate clearance then rotate retainer half
turn clockwise. Check pull rod is just held and
rotate retainer a further quarter turn clockwise
to lock.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
7.Connect battery earth lead.

INSTRUMENTS
REPAIRS 88-7
7.Remove 6 screws securing fuel tank sender
assembly access panel to floor.
8.Remove fuel tank sender assembly access
panel.
9.Disconnect multiplug from fuel tank sender
assembly.
10.Place a container beneath fuel tank to collect
possible fuel spillage.
11.Release and remove fuel pressure relief, fuel
feed and return hoses from fuel tank sender
assembly.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
12. Models with fuel burning heater (FBH):
Release clip and disconnect FBH fuel feed
hose from fuel tank sender assembly.
CAUTION: Always fit plugs to open
connections to prevent contamination.13.Use LRT-19-009 and remove locking ring from
fuel tank sender assembly.
14.Remove fuel tank sender assembly from fuel
tank and discard seal.
NOTE: The fuel pump and fuel gauge tank unit
are integral parts of the fuel pump housing and
cannot be renewed separately
M88 0359

INSTRUMENTS
88-8 REPAIRS
Refit
1.Clean fuel tank sender assembly and mating
face.
2.Fit new fuel tank sender assembly seal to fuel
tank.
3.Fit fuel tank sender assembly to fuel tank.
4.Using LRT-19-009 fit and secure fuel tank
sender assembly locking ring to fuel tank.
5. Models with FBH: Connect FBH hose to fuel
tank sender assembly and secure with clip.
6.Fit and secure pressure relief, fuel feed and
return hoses to fuel tank sender assembly.
7.Remove container from beneath fuel tank.
8.Connect multiplug to fuel tank sender
assembly.
9.Fit fuel tank sender assembly access panel and
secure with screws.
10.Position carpet to floor and secure with
fasteners.
11.Reposition rear seat.
12.Close rear and tail doors.
13.Connect battery earth lead.