oil LAND ROVER FREELANDER 2001 Owner's Guide

GENERAL DATA
04-10
Sensors:
Crankshaft sensor Siemens NSC 100630, Hall effect acting on profiled target on flywheel
Camshaft sensor:
⇒ Make / Type ITT NSC 100610 +0, Hall effect acting on camshaft reluctor ring
⇒ Ring TGN 100050
Oxygen sensor:
⇒ Make / Type NTK - MHK 100720
⇒ Heating element (nominal) 7 Watts
⇒ Sensor voltage - High≈ 900 mV
⇒ Sensor voltage - Low≈ 40 mV
Throttle potentiometer:
⇒ Make / Type CTS - MJC 100020
⇒ Total track resistance 4 kΩ ± 20%
⇒ Sensor supply voltage 5V ± 4%
TMAP sensor:
⇒ Make / Type Motorola - MHK 100820
⇒ Sensor supply voltage 5V ± 4%
Coolant temperature sensor:
⇒ Make / Type AB Electronik - MEK 100170; NTC thermistor bead
Oil temperature sensor
⇒ Make / Type AB Elektronik - MEK100170; NTC thermistor bead General

GENERAL DATA
04-11
Engine - KV6 Petrol
General
Type:
⇒ Up to 03 Model Year
⇒ From 03 Model Year2.5 litre V6, 24 valve, air assisted direct fuel injection petrol, water
cooled, transverse mounted
2.5 litre V6, 24 valve, direct fuel injection petrol, water cooled,
transverse mounted
Cylinder arrangement: 90° V6, numbered from the front of the engine
⇒ Left bank Cylinders 1, 3 and 5
⇒ Right bank Cylinders 2, 4 and 6
Bore (nominal) 80 mm (3.15 in.)
Stroke 82.8 mm (3.26 in.)
Capacity 2497 cm
3 (152.37 in3)
Firing order 1-6-5-4-3-2
Compression ratio 10.5 : 1 ± 0.5 : 1
Direction of rotation Clockwise viewed from front of engine
Maximum power 130 kW (177 bhp) @ 6500 rev/min.
Maximum torque 240.0 Nm (177 lbf.ft) @ 4000 rev/min.
Maximum engine speed:
⇒ Continuous 6500 rev/min.
⇒ Intermittent 6750 rev/min.
Idle speed 750 rev/min. ± 50 rev/min.
Weight (fully dressed, wet) 154 kg (340 lb)
Dimensions (dressed):
⇒ Length (nominal) 770 mm (30.3 in.)
⇒ Width (nominal) 750 mm (29.5 in.)
⇒ Height (nominal) 750 mm (29.5 in.)
Valve operation Self-adjusting lightweight hydraulic tappets operated directly by the
camshafts
Fuel injection system:
⇒ Make - Up to 03 Model Year
⇒ Make - From 03 Model YearSiemens engine management system
Siemens engine management system
⇒ Type - Up to 03 Model Year
⇒ Type - From 03 Model YearMulti-point, air assisted fuel injection controlled by ECM, electro-
mechanical injectors with twin sprays targeted on to back of inlet
valves
Multi-point fuel injection controlled by ECM, electro-mechanical
injectors with quadruple sprays targeted on to back of inlet valves
Inlet manifold Variable geometry
Spark plugs
⇒ Type
⇒ Plug gapNLP 100290
1.0 mm ± 0.05 mm (0.039 in. ± 0.002 in.)
Coils:
⇒ Make - Up to 03 Model Year
⇒ Make - From 03 Model Year
⇒ Type - Up to 03 Model Year
⇒ Type - From 03 Model YearBREMR
Champion BAE 403H
6 x coils (3 x plug top, 3 x remote mounted)
6 x coils (6 x plug top)
Emissions standard ECD3

GENERAL DATA
04-13
⇒⇒ Grade C (Blue)*
⇒ Grade 9 57.665 - 57.659 mm (2.2703 - 2.2700 in.)
⇒⇒ Grade A (Black)
*
⇒⇒ Grade B (Yellow)*
⇒⇒ Grade C (Green)*
†
Cylinder block / bearing ladder bore diameter grades* Crankshaft big-end journal grades
Main bearings
Quantity 4
Material / type Glacier AS15 - oil grooves in upper half shells, plain lower half shells
Clearance in bearings 0.021 - 0.039 mm (0.0008 - 0.0015 in.)
Thrust washers:
⇒ Type / position Glacier AS15 - thrust washer halves at top and bottom of rear main
bearing, oil grooves in top and bottom halves
⇒ Thrust washer halves thickness 2.61 - 2.65 mm (0.103 - 0.104 in.)
Main bearing thickness:
⇒ Red 1.930 - 1.927 mm (0.0760 - 0.0759 in.)
⇒ Blue 1.927 - 1.924 mm (0.0759 - 0.0757 in.)
⇒ Green 1.924 - 1.921 mm (0.0757 - 0.0756 in.)
⇒ Yellow 1.921 - 1.918 mm (0.0756 - 0.0755 in.)
⇒ Black 1.918 - 1.915 mm (0.0755 - 0.0754 in.)
Big-end bearings
Material / Type Glacier AS15 - plain upper and lower half shells with locating tags
Clearance in bearings 0.022 - 0.040 mm (0.0009 - 0.0016 in.)
Big-end bearing thicknesses:
⇒ Red 1.803 - 1.800 mm (0.0710 - 0.0709 in.)
⇒ Blue 1.800 - 1.797 mm (0.0709 - 0.0707 in.)
⇒ Green 1.797 - 1.794 mm (0.0707 - 0.0706 in.)
⇒ Yellow 1.794 - 1.791 mm (0.0706 - 0.0705 in.)
⇒ Black 1.791 - 1.788 mm (0.0705 - 0.0704 in.)
Big-end end-float 0.19 - 0.29 mm (0.007 - 0.011 in.)
Connecting rods
Type Forged steel H-sections with horizontally split big-ends
Distance between centres 151.31 - 151.41 mm (5.957 - 5.961 in.)
Gudgeon pins
Type Semi-floating offset towards thrust side
Fit in connecting rods Interference
⇒ Diameter - Red coded 17.997 - 18.000 mm (0.7085 - 0.7087 in.)
⇒ Diameter - Green coded 17.994 - 17.997 mm (0.7084 - 0.7085 in.)
⇒ Length 52.3 - 52.6 mm (2.059 - 2.071 in.)
⇒ Clearance in piston 0.011 mm (0.0004 in.)
Pistons
Type Aluminium alloy, tin plated, thermal expansion with offset gudgeon pin
Piston diameter (at right angle to gudgeon pin and 10
mm (0.4 in. from bottom of skirt):
⇒ Grade A 79.965 - 79.980 mm (3.1482 - 3.1488 in.)
⇒ Grade B 79.981 - 79.995 mm (3.1489 - 3.1494 in.) General

GENERAL DATA
04-14
Clearance in bore 20 mm (0.75 in.) from bottom of
cylinder bore0.034 - 0.035 mm (0.0013 - 0.0014 in.)
Maximum ovality 0.3 mm (0.012 in.)
Piston rings
Type:
⇒ Top compression ring Chrome plated steel
⇒ 2nd compression ring Chrome plated cast iron
⇒ Oil control ring Stainless steel top and bottom rails with expander ring
New ring to groove clearance:
⇒ Top compression ring 0.05 - 0.08 mm (0.0020 - 0.0031 in.)
⇒ 2nd compression ring 0.04 - 0.07 mm (0.0012 - 0.0024 in.)
⇒ Oil control ring 0.010 - 0.180 mm (0.0004 - 0.0071 in.)
Ring fitted gap 20 mm (0.75 in) from top of bore:
⇒ Top compression ring 0.20 - 0.35 mm (0.008 - 0.014 in.)
⇒ 2nd compression ring 0.28 - 0.45 mm (0.011 - 0.018 in.)
⇒ Oil control ring 0.25 - 1.00 mm (0.010 - 0.039 in.)
Piston ring width:
⇒ Top compression ring 3.1 ± 0.15 mm (0.122 ± 0.006 in.)
⇒ 2nd compression ring 3.15 - 3.45 mm (0.124 - 0.136 in.)
⇒ Oil control ring 2.286 - 2.438 mm (0.090 - 0.096 in.)
Camshaft
Type Twin camshafts on each cylinder bank retained by camshaft carrier,
line bored with cylinder head. Reluctor for camshaft sensor mounted
on left hand inlet camshaft
Camshaft identification:
⇒ Inlet Orange paint mark
⇒ Exhaust Blue paint mark
Bearings 5 per camshaft
Drive Toothed belt driven from crankshaft to front of inlet camshafts, 2 x
short toothed belts from rear of inlet camshafts to exhaust camshafts
Camshaft end-float 0.06 - 0.19 mm (0.002 - 0.007 in.)
⇒ Service limit 0.3 mm (0.012 in.)
Bearing clearance 0.025 - 0.059 mm (0.0010 - 0.0023 in.)
⇒ Service limit 0.1 mm (0.004 in.)
Tappets
Type Hydraulic self-adjusting, directly operated from camshafts
Tappet outside diameter 32.959 - 32.975 mm (1.2976 - 1.2982 in.)
Valve timing
Inlet valves:
⇒ Opens
⇒ Closes2° BTDC
54° ABDC
Exhaust valves:
⇒ Opens
⇒ Closes50° BBDC
14° ATDC
Valve maximum lift:
Inlet valves 8.2 mm (0.32 in.)
Exhaust valves 8.8 mm (0.35 in.) General

GENERAL DATA
04-15
* New metal dowels supplied with gasket must be fitted
Valves
Stem diameter:
⇒ Inlet valves 5.952 - 5.967 mm (0.2343 - 0.2349 in.)
⇒ Exhaust valves 5.947 - 5.962 mm (0.2341 - 0.2347 in.)
Stem to guide clearance:
Inlet valves 0.033 - 0.063 mm (0.0013 - 0.0025 in.)
⇒ Service limit 0.07 mm (0.0028 in.)
Exhaust valves 0.038 - 0.078 mm (0.0015 - 0.0013 in.)
⇒ Service limit 0.11 mm (0.0043 in.)
Valve stem fitted height:
⇒ New 38.93 - 39.84 mm (1.533 - 1.569 in.)
⇒ Service limit 40.10 mm (1.579 in.)
Valve guide fitted height 6.0 mm (0.24 in.)
Valve guide inside diameter 6.000 - 6.025 mm (0.2362 - 0.2372 in.)
Head diameter:
⇒ Inlet valves 31.4 - 31.6 mm (1.236 - 1.244 in.)
⇒ Exhaust valves 27.3 - 27.5 mm (1.075 - 1.083 in.)
Valve seat width:
⇒ Inlet valves
⇒ Exhaust valves1.2 mm (0.05 in.)
1.6 mm (0.06 in)
Seat face angle:
⇒ Inlet valves
⇒ Exhaust valves45°
45°
Valve face angle:
⇒ Inlet valves
⇒ Exhaust valves45°
45°
Valve springs
Free length 47.6 mm (1.874 in.)
Fitted length 37.0 mm (1.457 in.)
Load at fitted length 210 ± 13 N
Load at top of lift 440 ± 22 N
Lubrication
Type Cast aluminium, wet sump with full flow filtration
Oil pump: Crankshaft driven, high pressure die cast body
⇒ Outer rotor end-float 0.04 - 0.09 mm (0.0016 - 0.0035 in.)
⇒ Inner rotor end-float 0.04 - 0.09 mm (0.0016 - 0.0035 in.)
⇒ Inner rotor tip 0.05 - 0.13 mm (0.002 - 0.005 in)
⇒ Outer rotor to body diameterical clearance
0.13 - 0.23 mm (0.0051 - 0.0091 in.)
⇒ Rotor body to drive gear clearance (pump not fitted)
0.15 - 0.25 mm (0.0059 - 0.0098 in.)
Relief valve spring free length 38.90 mm (1.531 in)
Oil filter Full-flow disposable cartridge
Oil cooler Partial flow type
Pressure at idle (min.) 1.0 bar (14.5 lbf.in
2)
Pressure at 3000 rev/min. 3.0 bar (43.5 lbf.in
2)
Relief valve opening pressure 4.1 bar (59.5 lbf.in
2)
Low oil pressure switch opening pressure 0.3 - 0.5 bar (4.4 - 7.3 lbf.in
2) General

GENERAL DATA
04-24
Intermediate Reduction Drive (IRD)
Ratios:
⇒IRD input shaft to IRD countershaft 0.828 : 1
⇒ IRD countershaft to Front driveshaft 1.762 : 1
⇒ IRD countershaft to Propeller shaft 0.553 : 1
IRD ratio:
⇒ Td4 engines
⇒ K1.8 engines
⇒ KV6 engines1.467 : 1
1.467 : 1
1.359 : 1
Oil cooler Connected to vehicle cooling system

GENERAL DATA
04-28
Front Suspension
Type Independent, MacPherson struts with coil springs, lower "L" shaped
arms and anti-roll bar
Nominal height to wheel arch from hub centre* 453 mm (17.83 in)
Road spring identification (colour code):
Td4 with manual gearbox
⇒ Colour code YELLOW / BLUE
⇒ Total coils 6
⇒ Active coils 5
⇒ Wire diameter 14.87 mm (0.585 in)
⇒ Free length 367 mm (14.45 in)
Td4 with automatic gearbox, non air conditioning
⇒ Colour code YELLOW / WHITE
⇒ Total coils 6
⇒ Active coils 5
⇒ Wire diameter 14.87 mm (0.585 in)
⇒ Free length 367 mm (14.445 in)
Td4 with automatic gearbox and air conditioning
⇒ Colour code YELLOW / BROWN
⇒ Total coils 6
⇒ Active coils 5
⇒ Wire diameter 14.866 mm (0.5853 in)
⇒ Free length 375 mm (14.76 in)
K1.8 without air conditioning
⇒ Colour code YELLOW / PINK
⇒ Total coils 5.5
⇒ Active coils 4.5
⇒ Wire diameter 14.03 mm (0.552 in)
⇒ Free length 359 mm (14.13 in)
K1.8 with air conditioning
⇒ Colour code YELLOW / GREY
⇒ Total coils 5.5
⇒ Active coils 4.5
⇒ Wire diameter 14.03 mm (0.552 in)
⇒ Free length 359 mm (14.13 in)
KV6 without air conditioning
⇒ Colour code YELLOW / BLUE
⇒ Total coils 6
⇒ Active coils 5
⇒ Wire diameter 14.87 mm (0.585 in)
⇒ Free length 367 mm (14.45 in)
KV6 with air conditioning
⇒ Colour code YELLOW / WHITE
⇒ Total coils 6
⇒ Active coils 5
⇒ Wire diameter 14.87 mm (0.585 in)
⇒ Free length 371 mm (14.61 in)

GENERAL DATA
04-29
From 04MY: Models with Sports Suspension .
⇒ Colour code GREY / ORANGE
⇒ Total coils 5.5
⇒ Active coils 5.5
⇒ Wire diameter 15.5
⇒ Free length 308.5
Anti-roll bar diameter 20.5 mm (0.81 in)
* At unladen weight

GENERAL DATA
04-30
Rear Suspension
* At unladen weight
Type Independent, MacPherson struts with coil springs and lower
"trapezoidal links"
All models, except those with Sports
Suspension:Nominal height to wheel arch from hub
centre*463 mm (18.228 in) ± 10 mm (0.39)
Models with Sports Suspension only:Nominal height
to wheel arch from hub centre*433 mm (17.047 in)
Road spring identification:
All models except Sports Suspension
⇒ Colour code WHITE / GREEN
Total coils 6.42
Active coils 4.7
Wire diameter 13.825 mm (0.5443 in)
Free length 349.86 (13.774 in)
Models with Sports Suspension, (fitted from 04MY)
⇒ Colour code ORANGE / ORANGE
⇒ Total coils 6.8
⇒ Active coils 5.6
⇒ Wire diameter 13.97
⇒ Free length 311

GENERAL DATA
04-33
Heating and Ventilation
Air Conditioning
PTC heater - Td4 engine - if fitted
⇒ Make/Type Catem, 900 Watt output, 12 volt supply, located in Hevac unit
FBH - Td4 engine - if fitted
⇒ Make/Type Webasto Thermotop C, self-regulating, 5 kW output
System CFC free, sealed, closed-loop system
Refrigerant HFC - R134a
Refrigerant charge quantity:
All models except LHD KV6
LHD KV6 models540 ± 25 grammes
430 ± 25 grammes
Compressor, up to 04MY (some very early 04MY
vehicles may be fitted with this type of compressor):
⇒ Type Denso - variable displacement, 7-cylinder swash plate unit
⇒ High Pressure Blow-off valve 35.3 bar (3.53 MPa, 512 lbf/in
2)
⇒ Displacement (Min.) 5%
⇒ Displacement (Max.) 95%
Compressor, 04MY onwards
⇒ Type Sanden PXV16 - variable displacement, 7-cylinder swash plate unit
⇒ High Pressure Blow-off valve 35.3 bar (3.53 MPa, 512 lbf/in
2)
⇒ Displacement (Min.) 3%
⇒ Displacement (Max.) 100%
Lubricating oil Nippon Denso ND-8
Evaporator thermostat:
⇒ Opens
⇒ Closes+2 °C (+36 °F)
-4 °C (+25 °F)
Condenser fan control PWM signal from ECM to cooling fan control unit
Refrigerant Pressure Sensor
Low pressure limit:
⇒ A/C on (pressure rising) 2.25 ± 0.2 bar (32.6 ± 2.9 lbf/in
2)
⇒ A/C off (pressure falling) 1.96 ± 0.2 bar (28.4 ± 2.9 lbf/in
2)
High pressure limit:
⇒ A/C off (pressure rising) 31.4 ± 2.0 bar (455.3 ± 29 lbf/in
2)
⇒ A/C on (pressure falling) 25.5 ± 2.0 bar (369.8 ± 29 lbf/in
2)