engine LAND ROVER FREELANDER 2001 Repair Manual

TORQUE WRENCH SETTINGS
06-21
Intermediate Reduction Drive
+ Apply sealant, Part No. STC 4600 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Drain plug35 Nm 26 lbf.ft
Exhaust heatshield to exhaust mounting bracket 45 Nm 33 lbf.ft
Exhaust heatshield to IRD screws (Td4) 30 Nm 22 lbf.ft
Exhaust heatshield to IRD nut (K1.8 and KV6) 45 Nm 33 lbf.ft
Filler / level plug35 Nm 26 lbf.ft
IRD unit to gearbox bolts 90 Nm 66 lbf.ft
IRD end cover bolts
+30 Nm 22 lbf.ft
IRD support bracket to cylinder block bolt (K1.8) 48 Nm 35 lbf.ft
IRD support bracket to cylinder block bolt (K1.8) 48 Nm 35 lbf.ft
IRD support bracket to IRD bolts (Td4)
⇒ M8
⇒ M1030 Nm
50 Nm22 lbf.ft
37 lbf.ft
IRD support bracket to IRD bolts (K1.8 and KV6) 50 Nm 37 lbf.ft
IRD support bracket to sump (K1.8 and KV6) 88 Nm 65 lbf.ft
Lower engine steady to IRD support bracket bolts 100 Nm 74 lbf.ft
Manifold heatshield to IRD support bracket bolts (K1.8 and KV6) 9 Nm 6.5 lbf.ft
Manifold heatshield to IRD support bracket bolts (K1.8 and KV6) 25 Nm 18 lbf.ft
Manifold heatshield to pinion housing nut (KV6) 45 Nm 33 lbf.ft
Manifold heatshield to IRD (Td4) 30 Nm 22 lbf.ft
Breather pipe bracket screw 9 Nm 7 lbf.ft
Mass damper to pinion housing nuts (K1.8) 25 Nm 18 lbf.ft
Pinion nut150 Nm 111 lbf.ft
Pinion housing nuts 25 Nm 18 lbf.ft
Propeller shaft to IRD flange bolts 40 Nm 30 lbf.ft

TORQUE WRENCH SETTINGS
06-22
Automatic Gearbox – Jatco
†Tighten in sequence.
+ Apply sealant, Part No. STC 4600 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Air blast cooler assembly to chassis bolts:
⇒ Lower10 Nm 7.5 lbf.ft
⇒ Upper5 Nm 3.5 lbf.ft
Air blast cooler fan cowl to matrix bolts 5 Nm 3.5 lbf.ft
Air blast cooler fan motor to cowl bolts 5 Nm 3.5 lbf.ft
Air blast cooler multiplug mounting bracket nut 10 Nm 7.5 lbf.ft
Air blast cooler pipe union nuts 25 Nm 18 lbf.ft
Crankshaft Position (CKP) Sensor 9 Nm 7 lbf.ft
Closing panel to gearbox panel bolt 10 Nm 7.5 lbf.ft
Drive plate to converter bolts 45 Nm 33 lbf.ft
Earth lead to gearbox housing bolt 25 Nm 18 lbf.ft
Fluid cooler to mounting bracket bolts (KV6) 25 Nm 18 lbf.ft
Fluid cooler mounting bracket bolts (KV6):
⇒ M825 Nm 18 lbf.ft
⇒ M1285 Nm 63 lbf.ft
Fluid cooler mounting bolts (Td4):
⇒ 2 off45 Nm 33 lbf.ft
⇒ 1 off25 Nm 18 lbf.ft
Fluid cooler hoses to gearbox 18 Nm 13 lbf.ft
Fluid cooler hose unions 18 Nm 13 lbf.ft
Fluid pan bolts
† +7 Nm 5 lbf.ft
Gearbox closing plate bolt (Td4) 10 Nm 7.5 lbf.ft
Gearbox drain plug 45 Nm 33 lbf.ft
Gearbox level plug 14 Nm 10 lbf.ft
Gearbox housing to sump 85 Nm 63 lbf.ft
Gearbox to engine bolts 85 Nm 63 lbf.ft
Gearbox mounting bracket bolts 85 Nm 63 lbf.ft
Gearbox mounting through bolt 100 Nm 74 lbf.ft
Inhibitor switch bolts 3 Nm 2.2 lbf.ft
IRD cooling hose retainer bolt (KV6) 25 Nm 18 lbf.ft
IRD support bracket mounting bolts
† (KV6) 50 Nm 37 lbf.ft
IRD support bracket to engine front mounting bracket bolts
† (KV6) 50 Nm 37 lbf.ft
IRD support bracket to sump bolts
† (KV6) 45 Nm 33 lbf.ft
IRD to gearbox bolts (KV6) 80 Nm 59 lbf.ft
Manifold heatshield to IRD support bracket (KV6):
⇒ Bolts9 Nm 7 lbf.ft
⇒ Nut45 Nm 33 lbf.ft
Manifold heatshield to IRD pinion housing nut (KV6) 25 Nm 18 lbf.ft
Selector housing nuts 10 Nm 7.5 lbf.ft
Selector cable trunnion nut 6 Nm 4.5 lbf.ft
Selector lever to gearbox selector shaft nut 25 Nm 18 lbf.ft
Starter motor to gearbox bolts 45 Nm 33 lbf.ft
Torque converter access plate bolts 9 Nm 7 lbf.ft

TORQUE WRENCH SETTINGS
06-25
Steering
* Tighten with weight of vehicle on suspension
TORQUE DESCRIPTION METRIC IMPERIAL
Ball joint to steering arm nuts 55 Nm 41 lbf.ft
Coolant rail to cylinder block bolts (KV6) 9 Nm 7 lbf.ft
Gear change linkage to bulkhead bolts (Td4 manual) 25 Nm 18 lbf.ft
Heatshield nuts (KV6) 25 Nm 18 lbf.ft
Interlock cable to column lock union (JATCO) 4 Nm 3 lbf.ft
IRD hose clip bolt (Td4) 25 Nm 18 lbf.ft
Key cable clamp bolt (JATCO) 6 Nm 4.5 lbf.ft
PAS pipe clip to engine lifting eye bolt 10 Nm 7.5 lbf.ft
PAS high pressure pipe clip bolt 8 Nm 6 lbf.ft
PAS fluid pipe bracket bolts 10 Nm 7.5 lbf. ft
PAS outlet hose to pump banjo bolt (KV6 & K1.8) 20 Nm 15 lbf.ft
PAS outlet hose to pump banjo bolt (Td4) 25 Nm 18 lbf.ft
PAS outlet pipe clip bolt 22 Nm 16 lbf.ft
PAS pipe to clamp bolt 22 Nm 16 lbf. ft
PAS pipe to engine front mounting plate bolt (KV6) 25 Nm 18 lbf.ft
PAS pipe support bracket to RH hydramount nut (KV6) 85 Nm 63 lbf.ft
PAS pipe to RH turret clip bolt 10 Nm 7.5 lbf.ft
PAS pump high pressure pipe union 25 Nm 18 lbf.ft
PAS pump pulley bolts 10 Nm 7.5 lbf.ft
PAS pump to mounting bracket bolts (KV6 & K1.8) 25 Nm 18 lbf.ft
PAS pump to mounting bracket bolts (Td4):
⇒ M610 Nm 7.5 lbf.ft
⇒ M825 Nm 18 lbf.ft
PAS pump mounting to cylinder block bolts 45 Nm 33 lbf.ft
PAS rack fluid feed pipe union nut 18 Nm 13 lbf. ft
PAS rack fluid return pipe union nut 22 Nm 16 lbf. ft
PAS rack mounting and clamp to bulkhead bolts 45 Nm 33 lbf. ft
Ram feed pipe union nuts:
⇒ Small (6mm) diameter 18 Nm 13 lbf.ft
⇒ Large (10 mm) diameter 24 Nm 18 lbf.ft
Steering column height adjuster clamp bolt and nut 10 Nm 7.5 lbf.ft
Steering column height adjuster clamp bolt and nut 12 Nm 9 lbf.ft
Steering column bracket side support bolt 10 Nm 7.5 lbf.ft
Steering column lock bolt SHEAR
Steering column to fascia support rail (Nyloc) nuts and bolts 14 Nm 10 lbf.ft
Steering column to PAS rack pinion clamp pinch bolt
132 Nm 24 lbf. ft
Steering wheel nut 45 Nm 33 lbf.ft
Track-rod ends to steering arm nuts 55 Nm 41 lbf.ft
Track-rod end pinch bolt * 28 Nm 21 lbf.ft
Track-rod to rack bolts 100 Nm 74 lbf.ft
Turnbuckle lock nuts 90 Nm 66 lbf.ft

TORQUE WRENCH SETTINGS
06-26
Front Suspension and Subframe
1 Use NEW nuts
2 Tighten with weight of vehicle on suspension
3 Tighten in diagonal sequence
TORQUE DESCRIPTION METRIC IMPERIAL
Anti-roll bar saddle clamp to subframe bolts 23 Nm 17 lbf.ft
Anti-roll bar link to damper nut 45 Nm 33 lbf.ft
Anti-roll bar to link nut 55 Nm 41 lbf.ft
Damper assembly to body top mounting nuts
245 Nm 33 lbf.ft
Damper to hub nuts and bolts
2205 Nm 151 lbf.ft
Damper shaft locking nut 57 Nm 42 lbf.ft
Engine lower steady to support beam bolt 100 Nm 74 lbf.ft
Engine tie-bar to sump bolts 100 Nm 74 lbf.ft
Front subframe to body front bolts 190 Nm 140 lbf.ft
Hub drive shaft nut
1400 Nm 295 lbf.ft
Hub assembly to lower swivel joint nut 65 Nm 48 lbf.ft
Lower arm front bush to subframe bolt
2190 Nm 140 lbf.ft
Lower arm rear bush housing bolts to body
2105 Nm 77 lbf.ft
Lower arm to rear bush housing nut
2140 Nm 103 lbf.ft
Road wheel nuts
3115 Nm 85 lbf.ft
Support beam to body bolts 190 Nm 140 lbf.ft

TORQUE WRENCH SETTINGS
06-28
Brakes
1 Use NEW bolts
TORQUE DESCRIPTION METRIC IMPERIAL
ABS ECU pipe unions 17 Nm 12 lbf.ft
ABS modulator to mounting bracket bolts 9 Nm 7 lbf.ft
ABS modulator mounting bracket to inner wing:
⇒ Nuts
⇒ Bolts13 Nm
8 Nm10 lbf.ft
6 lbf.ft
Bleed screw - front calipers 10 Nm 7.5 lbf.ft
Brake servo to bulkhead nuts 22 Nm 16 lbf.ft
EGR cooler to mounting bolts 25 Nm 18 lbf.ft
EGR pipe support bracket to engine lifting bracket bolts 25 Nm 18 lbf.ft
Front caliper brake hose banjo bolt 28 Nm 21 lbf.ft
Front caliper guide pin bolts 27 Nm 20 lbf.ft
Front caliper mounting bolts 100 Nm 74 lbf.ft
Front disc shield to hub screw 8.5 Nm 6.3 lbf.ft
Front disc to drive flange screws 5 Nm 3.7 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Handbrake cable to body and subframe bolts 22 Nm 16 lbf.ft
Handbrake cable retaining plate bolts 22 Nm 16 lbf.ft
Handbrake lever assembly to body bolts 22 Nm 16 lbf.ft
Hill Descent Control (HDC) switch bolt 5 Nm 3.5 lbf.ft
Master cylinder to servo nuts 25 Nm 18 lbf.ft
PAS oil cooler pipe bolts 10 Nm 7.5 lbf.ft
Primary and secondary brake pipe union nuts 17 Nm 12 lbf.ft
Rear wheel cylinder pipe union nut 17 Nm 12 lbf.ft
Rear wheel cylinder to backplate bolts 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 6 Nm 4.5 lbf.ft
Road wheel nuts 115 Nm 85 lbf.ft
Turbocharger intercooler pipe to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger pipe to coolant rail bolt 25 Nm 18 lbf.ft
Vacuum pump bolts
122 Nm 16 lbf.ft
Vacuum reservoir to mounting bracket nut 10 Nm 7.5 lbf.ft

TORQUE WRENCH SETTINGS
06-30
Body
TORQUE DESCRIPTION METRIC IMPERIAL
Doors
Door lock striker to body screws 10 Nm 7 lbf.ft
Door stiffener Torx screws 9 Nm 7 lbf.ft
Front door control unit to glass clamp bolts 9 Nm 7 lbf.ft
Front door hinge bolts 30 Nm 22 lbf.ft
Rear door glass clamp bolts 8 Nm 6 lbf.ft
Tail door exterior handle nuts 5 Nm 3.7 lbf.ft
Tail door glass clamp bolts 8 Nm 6 lbf.ft
Tail door glass regulator lock nuts 14 Nm 10 lbf.ft
Tail door hinge bolts 30 Nm 22 lbf.ft
Exterior Fittings
Bonnet hinge, bolts 9 Nm 6.5 lbf.ft
Bonnet release lever to 'A' post bolt 9 Nm 6.5 lbf.ft
Exterior mirror to door Torx screws 6 Nm 4.4 lbf.ft
Front wing bolts5 Nm 3.7 lbf.ft
Spare wheel mounting bracket:
⇒ Bolts13 Nm 10 lbf.ft
⇒ Nuts25 Nm 18 lbf.ft
Spare wheel to bracket retention nuts 45 Nm 33 lbf.ft
Splash shield bolts 10 Nm 7 lbf.ft
Underbelly panel to body bolts 45 Nm 33 lbf.ft
Underbelly panel to body rear screws 8 Nm 6 lbf.ft
3 door vehicles
Hard back catch Torx screws 10 Nm 7.5 lbf.ft
Hard back retainer Torx screws 10 Nm 7.5 lbf.ft
Soft back support bracket bolts 25 Nm 18 lbf.ft
5 door vehicles
Roof rack side rail bolts 22 Nm 16 lbf.ft
Interior Trim Components
Engine compartment fusebox bolts 8 Nm 6 lbf.ft
Passenger compartment fusebox mounting plate to body and steering column
bracket bolts8 Nm 6 lbf.ft
Passenger compartment fusebox to mounting plate bolts 8 Nm 6 lbf.ft
Seats
Front seat runner to body bolts 45 Nm 33 lbf.ft
Front seat squab frame to cushion frame Torx bolts 45 Nm 33 lbf.ft
Rear bench seat to body bolts 25 Nm 18 lbf.ft
Rear seat cushion to squab Torx bolts 28 Nm 21 lbf.ft
Rear seat catch assembly Torx bolts 32 Nm 24 lbf.ft
Rear seat squab lock Torx screws 20 Nm 15 lbf.ft
Rear seat squab to cushion Torx bolts 28 Nm 21 lbf.ft
Rear seat hinge Torx bolts 25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-35
Electrical
TORQUE DESCRIPTION METRIC IMPERIAL
Alternator drive belt tensioner bolt 25 Nm 18 lbf.ft
Alternator mounting bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator pivot and adjustment bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator to front mounting plate nut and bolts (KV6) 45 Nm 33 lbf.ft
Alternator support bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator pivot and adjustment bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator to mounting bracket bolts (Td4):
⇒ M825 Nm 18 lbf.ft
⇒ M1045 Nm 9.5 lbf.ft
Alternator upper and lower bolts (K1.8 with A/C) 45 Nm 33 lbf.ft
Ancillary drive belt idler pulley to mounting Allen bolt (Td4) 25 Nm 18 lbf.ft
Battery cable to alternator terminal nut (Td4 & KV6) 10 Nm 7.5 lbf.ft
Battery cable to starter motor solenoid nut (K1.8) 8 Nm 6 lbf.ft
Battery cable to starter motor solenoid nut (K1.8) 13 Nm 9.5 lbf.ft
Battery clamp bolt 12 Nm 9 lbf.ft
Battery and starter motor lead to underbonnet fusebox bolts 8 Nm 6 lbf.ft
'E' box mounting nut 9 Nm 7 lbf.ft
Passenger compartment fusebox mounting plate to body bolts 8 Nm 6 lbf.ft
Passenger compartment fusebox to mounting plate bolts 8 Nm 6 lbf.ft
Starter motor mounting bolts (Td4) 45 Nm 33 lbf.ft
Starter motor to engine upper and lower nuts and bolts (K1.8) 45 Nm 33 lbf.ft
Starter motor to engine upper and lower nuts and bolts (K1.8) 80 Nm 59 lbf.ft

LIFTING AND TOWING
08-1
LIFTING AND TOWING
Jacking
The following instructions must be carried out before
raising the vehicle off the ground:
lUse a solid level surface.
lApply parking brake.
lSelect 1st. gear in main gearbox and ensure
HDC is not selected.
CAUTION: To avoid damage to under body
components of the vehicle, adhere to the
following jacking procedures:
DO NOT POSITION JACKS OR AXLE STANDS
UNDER THE FOLLOWING COMPONENTS:
lBumpers
lBrake or Fuel lines
lExhaust pipe
lSuspension components
lSteering rack and linkages
lFuel tank
lEngine sump
lGearbox
lIRD unit
Jack or support vehicle only on approved jacking
points as detailed in the following illustration:
Front (hydraulic jack) and side (vehicle jack) jacking
pointsSafety stand positions under longitudinal members
Rear (hydraulic jack) and side (vehicle jack) jacking
points
Vehicle jack
The jack provided with the vehicle is only intended to
be used in an emergency, for changing a tyre. Do
NOT use the jack for any other purpose. Refer to the
Owner's Handbook for vehicle jack location points
and procedure. Never work under a vehicle only
supported by the vehicle jack.
Hydraulic jack
A hydraulic jack with a minimum 1500 kg (3,300 lbs)
load capacity must be used.
WARNING: Do not work on or under a vehicle
supported only by a jack. Always support the
vehicle on safety stands.

LIFTING AND TOWING
08-2
Raising the front of a vehicle
Position the cup of the hydraulic arm under the
centre of the front body crossmember assembly.
Use jack to raise front road wheels to enable safety
stands to be installed under the front end of each
longitudinal member.
Carefully lower jack until vehicle sits securely on
safety stands.
Before working on the underside of a vehicle re-
check the stability of the vehicle on the stands.
Use the reverse procedure when removing a vehicle
from stands.
NOTE: For some repair operations it may be
necessary to use a jack to support the engine under
the sump. In this case, a block of wood should be
used on the jack to protect the sump.
Raising the rear of a vehicle
Position cup of hydraulic arm under the centre of the
rear subframe crossmember at the position
identified by the embossed arrows.
Use jack to raise rear road wheels to enable safety
stands to be installed under the rear ends of the
body longitudinal members.
Carefully lower jack until vehicle sits securely on
safety stands.
Before working on the underside of a vehicle, re-
check the stability of the vehicle on the stands.
Use the reverse procedure when removing a vehicle
from stands.
Wheel-free lift
Locate the lifting pads under the ends of the body
longitudinal members. Raise the ramp to support the
weight of the vehicle, ensure the vehicle is secure on
the lifting pads, then raise the ramp to the required
height.
Towing
General
The vehicle has permanent four wheel drive. The
following instructions must be adhered to:
Towing the vehicle on all four wheels with driver
operating steering and brakes
lTurn ignition key to position '1' to release
steering lock and then to position 'II' to enable
the brake lights, wipers and direction indicators
to be operated, if necessary.
l Select neutral in gearbox and ensure HDC (hill
descent control) is deselected.
lSecure tow rope, chain or cable to towing eye.
lRelease the parking brake.
CAUTION: The brake servo and power assisted
steering system will not be functional without the
engine running. Greater pedal pressure will be
required to apply the brakes and the steering
system will require greater effort to turn the front
road wheels. The vehicle tow connection should
only be used under normal road conditions,
'snatch' recovery should be avoided.
Suspended tow by breakdown vehicle
Mark propeller shaft drive flanges and mating flanges
with identification lines to enable the propeller shaft
to be refitted in its original position.
Remove the propeller shaft fixings then remove the
shaft from the vehicle.
CAUTION: To prevent vehicle damage, rear
propeller shaft MUST BE removed.

LIFTING AND TOWING
08-4
Emergency starting
WARNING: Battery fluid (electrolyte) contains
sulphuric acid. It may cause severe burns if it
gets on your skin or in your eyes. Wear
protective clothing and a face shield.
If electrolyte gets on your skin or clothes,
immediately rinse it off with water.
If electrolyte gets in your eyes, immediately flush
eyes with water for at least 15 minutes and seek
medical help.
To Jump Start - Negative Ground Battery
Position vehicles so that jump leads will reach,
ensuring that vehicles DO NOT TOUCH,
alternatively a fully charged slave battery may be
positioned on the floor adjacent to the vehicle.
Ensure that:
lthe ignition and all electrical accessories are
switched off
lthe parking brake is applied and neutral is
selected on gearbox
Connect the jump leads as follows:
WARNING: Making final cable connection could
cause an electrical arc, which if made near
battery could cause an explosion.
aConnect one end of first jumper cable to
positive (+) terminal of booster battery.
bConnect other end of first jumper cable to
positive (+) terminal of discharged battery.
cConnect one end of second jumper cable to
negative terminal of booster battery.
dConnect other end of second jumper cable to a
good earth point on the engine, NOT TO
NEGATIVE TERMINAL OF DISCHARGED
BATTERY.
CAUTION: Keep jumper leads away from moving
parts, pulleys, drive belts and fan blade
assembly.If the booster battery is installed in another vehicle,
start engine and allow to idle.
Start engine of vehicle with discharged battery,
following starting procedure in Owners' Handbook.
CAUTION: If vehicle fails to start within a
maximum time of 12 seconds, switch ignition off
and investigate cause. Failure to follow this
instruction could result in irreparable damage to
catalyst.
To disconnect:
l Remove negative (-) jumper cable from the
engine and then terminal of booster battery.
lRemove positive (+) jumper cable from positive
terminals of booster battery and discharged
battery.