display Lexus CT200h 2011 Owner's Manual (in English)

576
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Follow the correction procedures.
A warning message is shown on the multi-information display.
After taking the specified steps to correct the suspected problem,
check that the warning message goes off.
Warning messageDetailsCorrection procedure
Indicates that the
washer fluid level is
low
Add washer fluid.
(If equipped)
Indicates that the
pre-crash safety system
is not currently func-
tional because the grille
or the sensor is dirty
This message also
appears when the pre-
crash safety system is
not functional due to
overheating.
• Check the grille and
the sensor and clean
them if they are dirty.
• In case of overheat-
ing, the system will
become functional
once the system cools
down.

5
579
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Once
Con-
tinu-
ous
(Displayed alter-
nately)
(Flashes)
An attempt was
made to exit the
vehicle with the
electronic key
and lock the
doors without
first turning the
“POWER”
switch off.
Turn the
“POWER”
switch off and
lock the doors
again.
Once
(Flashes)
An attempt was
made to start the
hybrid system
without the elec-
tronic key being
present, or the
electronic key
was not func-
tioning nor-
mally.
An attempt was
made to drive
when the regular
key was not
inside the vehi-
cle.
Confirm that the
electronic key is
inside the vehi-
cle.

580
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Con-
tinu-
ous

(Flashes)
The driver’s
door was opened
while any shift
position other
than P was
selected without
turning off the
“POWER”
switch.
Shift the shift
position to P.
Con-
tinu-
ousCon-
tinu-
ous
(Displayed alter-
nately)
(Flashes)
The electronic
key was carried
outside the vehi-
cle and the
driver’s door
was opened and
closed while any
shift position
other than P was
selected without
turning off the
“POWER”
switch.
• Shift the shift
position to P.
• Bring the elec-
tronic key back
into the vehi-
cle.

5
585
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Warning message in radar cruise mode
In the following cases, the warning message may not be displayed even if
vehicle-to-vehicle distance decreases:
When your vehicle and the vehicle ahead are traveling at the same speed
or the vehicle ahead is traveling more quickly than your vehicle
When the vehicle ahead is traveling at a very low speed
Immediately after cruise control speed is set
At the instant the accelerator pedal is depressed

606
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)To inject the sealant and inflate
the tire, turn the compressor
switch on.
Use the kit with the top facing
upward.
Inflate the tire until the recom-
mended pressure is reached.
The sealant will be injected
and the pressure will spike
to 300 kPa (3.0 kgf/cm
2
or bar, 44 psi) or 400 kPa
(4.0 kgf/cm2 or bar, 58 psi),
then gradually decrease.
The air pressure gauge will
display the actual tire infla-
tion pressure about 1 minute
after the switch is turned on.
• Turn the compressor switch
off and then check the tire
inflation pressure. Being
careful not to over inflate,
check and repeat the infla-
tion procedure until the rec-
ommended tire inflation
pressure is reached.
STEP10
STEP 11

5
627
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
If your vehicle overheats
Correction procedures
If the high coolant temperature warning light comes on or
flashes
Stop the vehicle in a safe place and turn off the air condi-
tioning system.
Check to see if steam is coming out from the engine area.
If you see steam:
Stop the hybrid system. Carefully lift the hood after the
steam subsides and then restart the hybrid system.
If you do not see steam:
Leave the hybrid system operating and carefully lift the
hood.
Check to see if the cooling fans are operating.
If the fans are operating:
Wait until the high coolant temperature warning light goes
off and then stop the hybrid system.
If the fans are not operating:
Stop the hybrid system immediately and call any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
The following may indicate that your vehicle is overheating:
The high coolant temperature warning light comes on or
flashes:
The engine may be overheating.
“HYBRID SYSTEM OVERHEAT” is shown on the multi-
information display:
STEP1
STEP2
STEP3

5
629
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)If “HYBRID SYSTEM OVERHEAT” is shown on the multi-
information display
Stop the vehicle in a safe place and turn off the air condi-
tioning system.
Leave the hybrid system operating and carefully lift the
hood.
Check if the cooling fans are operating.
If the fans are operating:
Wait until the “HYBRID SYSTEM OVERHEAT” message
disappears and then stop the hybrid system.
If the message does not disappear, call any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
If the fans are not operating:
Stop the hybrid system immediately and call any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
After the hybrid system has
cooled down, check the power
control unit coolant level and
inspect the cooling system for
leaks.
If the engine compartment
cover needs to be removed: P.
486
STEP1
STEP2
STEP3
STEP4

644
6-1. Specifications
CT200h_EE (OM76041E)
Oil viscosity (0W-20 is explained here as an example):
• The 0W in 0W-20 indicates the characteristic of the oil which
allows cold startability. Oils with a lower value before the W allow
for easier starting of the engine in cold weather.
• The 20 in 0W-20 indicates the viscosity characteristic of the oil
when the oil is at high temperature. An oil with a higher viscosity
(one with a higher value) may be better suited if the vehicle is oper-
ated at high speeds, or under extreme load conditions.
How to read oil container labels:
Either or both API registered marks are added to some oil contain-
ers to help you select the oil you should use.
API Service Symbol
Top portion: The oil quality des-
ignation by API (American
Petroleum Institute) (SM)
Center portion: The SAE vis-
cosity grade (SAE 0W-20)
Lower portion: “Energy-Con-
serving” means that the oil has
fuel-saving capabilities.
ILSAC Certification Mark
The ILSAC (International
Lubricant Standardization and
Approval Committee) Certifica-
tion Mark is displayed on the
front of the container.

655
6
Vehicle specifica-
CT200h_EE (OM76041E)
6-2. Customization
Customizable features
Customizing vehicle features
It is possible to customize certain vehicle features using the
“DISP” switch.
When customizing vehicle features, ensure that the vehicle is
parked in a safe place with the shift position in P and the parking
brake set.
Press the “DISP” switch to dis-
play the “SETTINGS” screen
while the vehicle is stopped,
and then press and hold the
“DISP” switch to display the
customize mode screen.
Your vehicle includes a variety of electronic features that can be per-
sonalized to suit your preferences. Programming these preferences
requires specialized equipment and may be performed by your Lexus
dealer.
It is also possible to customize certain vehicle features yourself using
the “DISP” switch and the navigation screen.
For instructions on customizing vehicle features using the navigation
screen, refer to the “Navigation System Owner’s Manual”.
Some function settings are changed simultaneously with other func-
tions being customized. Contact any authorized Lexus dealer or
STEP1

668
6-2. Customization
CT200h_EE (OM76041E)
Instru-
ment clus-
ter
(
P. 216)
TA C H O
METER
(Display of the
tachometer
and Hybrid
System Indica-
tor)
AUTO
KEEP ON*5
–OO
OFF
ECO LAMP
(On/off opera-
tion of the Eco
lamp)ECO
DRIVE
SUPPORTKEEP ON
–OO
OFF
SPORT
LAMP
(On/off opera-
tion of the
sport lamp)
AUTOOFF–OO
LAMP
BRIGHT-
NESS
(Brightness of
ECO lamp and
SPORT lamp)
STAN-
DARDBRIGHT–OO
ItemFunctionDefault
settingCustomized
setting