start Lexus CT200h 2012 (in English) Owner's Guide

125
1-5. Opening and closing the windows and moon roof
1
Before driving
CT200h_OM_OM76067E_(EE)
When the power window does not close normally
If the jam protection function is operating abnormally and a window cannot
be closed, perform the following operations using the power window switch
on the relevant door.
After stopping the vehicle, the window can be closed by holding the
power window switch in the one-touch closing position while the
“POWER” switch is turned to ON mode.
If the window still cannot be closed even by carrying out the operation
explained above, initialize the function by performing the following pro-
cedure.
Hold the power window switch in the one-touch closing position.
Continue holding the switch for a further 6 seconds after the win-
dow has closed.
Hold the power window switch in the one-touch opening position.
Continue holding the switch for a further 2 seconds after the win-
dow has opened completely.
Hold the power window switch in the one-touch closing position
once again. Continue holding the switch for a further 2 seconds
after the window has closed.
If you release the switch while the window is moving, start again from the
beginning.
If the window continues to close but then re-open slightly even after per-
forming the above procedure correctly, have the vehicle inspected by any
authorized Lexus dealer or repairer, or another duly qualified and equipped
professional.
STEP1
STEP2
STEP3

135
1
Before driving
CT200h_OM_OM76067E_(EE)
1-7. Theft deterrent system
Immobilizer system
System maintenance
The vehicle has a maintenance-free type immobilizer system.
Conditions affecting operation
Depending on the surrounding environment and conditions, the immobilizer
system may not operate properly. This may prevent the hybrid system from
starting. (P. 8 6 )
The vehicle’s keys have built-in transponder chips that prevent the
hybrid system from starting if a key has not been previously registered
in the vehicle’s on-board computer.
Never leave the keys inside the vehicle when you leave the vehicle.
The indicator light flashes
after the “POWER” switch
has been turned off to indi-
cate that the system is operat-
ing.
The indicator light stops
flashing after the “POWER”
switch has been turned to
ACCESSORY or ON mode

142
1-7. Theft deterrent system
CT200h_OM_OM76067E_(EE)
Alarm
: If equipped
The system sounds the alarm and flashes lights when forcible entry is
detected.
Triggering of the alarm
The alarm is triggered in the following situations when the
alarm is set:
A locked door is unlocked or opened in any way other than
using the entry function (vehicles with a smart entry & start
system) or wireless remote control.
The hood is opened.
The intrusion sensor detects something moving inside the
vehicle. (An intruder gets in the vehicle.) (if equipped)
The tilt sensor detects a change of vehicle inclination. (if
equipped)
The back door window is broken. (if equipped)
Setting the alarm system
Close the doors and hood,
and lock all the doors using
the entry function (vehicles
with a smart entry & start
system) or wireless remote
control. The system will be
set automatically after 30
seconds.
The indicator light changes
from being on to flashing

143
1-7. Theft deterrent system
1
Before driving
CT200h_OM_OM76067E_(EE)
Intrusion sensor and tilt sensor (if equipped)
This system is designed to deter and prevent vehicle theft but does
not guarantee absolute security against all intrusions.
The intrusion sensor detects intruders or movement in the vehi-
cle.
The tilt sensor detects changes in vehicle inclination, such as
when the vehicle is towed away.
The intrusion sensor and tilt sensor can be canceled using the can-
cel switch.
Deactivating or stopping the alarm
Do one of the following to deactivate or stop the alarm.
Unlock the doors using the entry function (vehicles with a
smart entry & start system) or wireless remote control.
Start the hybrid system. (The alarm will be deactivated or
stopped after a few seconds.)

2When driving
185
CT200h_OM_OM76067E_(EE)
2-1. Driving procedures
Driving the vehicle........... 186
Power (ignition) switch .... 198
EV drive mode ................. 204
Hybrid transmission ......... 207
Turn signal lever .............. 216
Parking brake ................... 217
Horn ................................. 218
2-2. Instrument cluster
Gauges and meters ........... 219
Indicators and warning
lights .............................. 225
Multi-information
display ............................ 2292-3. Operating the lights and
windshield wipers
Headlight switch .............. 235
Fog light switch ............... 239
Windshield wipers and
washer ............................ 241
Rear window wiper and
washer ............................ 247
Headlight cleaner switch . 249
2-4. Using other driving
systems
Cruise control .................. 250
Dynamic radar cruise
control ............................ 255
Lexus parking
assist-sensor ................... 273
Rear view monitor
system ............................ 282
Driving assist systems ..... 291
Hill-start assist control ..... 296
PCS (Pre-Crash Safety
system)........................... 299
2-5. Driving information
Cargo and luggage ........... 308
Winter driving tips ............ 311
Trailer towing .................. 315

186
CT200h_OM_OM76067E_(EE)
2-1. Driving procedures
Driving the vehicle
The following procedures should be observed to ensure safe driving:
Starting the hybrid system
P. 198
Driving
With the brake pedal depressed, shift the shift position to
D.
(P. 207)
Check that the shift position indicator shows D.
Release the parking brake. (P. 217)
Gradually release the brake pedal and gently depress the
accelerator pedal to accelerate the vehicle.
Stopping
With the shift position in D, depress the brake pedal.
If necessary, set the parking brake.
When the vehicle will be stopped for an extended period of
time, shift the shift position to P. (
P. 207)
Parking the vehicle
Stop the vehicle completely.
Set the parking brake. (P. 217)
Shift the shift position to P. (P. 2 1 0 )
Check that the shift position indicator shows P. (P. 207)
Press the “POWER” switch to stop the hybrid system.
Slowly release the brake pedal.
Lock the door, making sure that you have the electronic
key on your person.
STEP1
STEP2
STEP3
STEP1
STEP2
STEP1
STEP2
STEP3
STEP4
STEP5
STEP6

187
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
Starting off on a uphill
Firmly set the parking brake with the brake pedal
depressed, and then shift the shift position to D.
Release the brake pedal and gently depress the accelerator
pedal.
Release the parking brake.
When starting off on a uphill
The hill-start assist control is available. (P. 296)
Driving in the rain
Drive carefully when it is raining, because visibility will be reduced, the
windows may become fogged-up, and the road will be slippery.
Drive carefully when it starts to rain, because the road surface will be
especially slippery.
Refrain from high speeds when driving on an expressway in the rain,
because there may be a layer of water between the tires and the road sur-
face, preventing the steering and brakes from operating properly.
STEP1
STEP2
STEP3

189
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
CAUTION
When starting the vehicle
Always keep your foot on the brake pedal while stopped with the hybrid
system operating. This prevents the vehicle from creeping.
When driving the vehicle
Do not drive if you are unfamiliar with the location of the brake and accel-
erator pedals to avoid depressing the wrong pedal.
• Accidentally depressing the accelerator pedal instead of the brake
pedal will result in sudden acceleration that may lead to an accident
that could result in death or serious injury.
• When backing up, you may twist your body around, leading to a diffi-
culty in operating the pedals. Make sure to operate the pedals properly.
• Make sure to keep a correct driving posture even when moving the
vehicle only slightly. This allows you to depress the brake and acceler-
ator pedals properly.
• Depress the brake pedal using your right foot. Depressing the brake
pedal using your left foot may delay response in an emergency, result-
ing in an accident.
The driver should pay extra attention to pedestrians when the vehicle is
powered only by the electric motor (traction motor). Because there is no
engine noise, the pedestrians may misjudge the vehicle’s movement.
Do not drive the vehicle over or stop the vehicle near flammable materi-
als.
The exhaust system and exhaust gases can be extremely hot. These hot
parts may cause a fire if there is any flammable material nearby.
Do not let the vehicle roll backward while a forward driving position is
selected, or roll forward while the shift position is in R.
Doing so may result in an accident or damage to the vehicle.

198
2-1. Driving procedures
CT200h_OM_OM76067E_(EE)
Power (ignition) switch
Performing the following operations when carrying the electronic key
on your person starts the hybrid system or changes “POWER” switch
modes.
Starting the hybrid system
Check that the parking brake is set.
Firmly depress the brake pedal.
Check that the “POWER” switch indicator turns green. If the
indicator does not turn green, the hybrid system cannot be
started.
When the shift position is N, the hybrid system cannot start.
Shift the shift position to P when starting the hybrid system.
(P. 210)
Press the “POWER” switch.
Continue depressing the
brake pedal until the hybrid
system is completely started.
The hybrid system can be
started from any “POWER”
switch mode.
STEP1
STEP2
STEP3

199
2-1. Driving procedures
2
When driving
CT200h_OM_OM76067E_(EE)
Check that the “READY” indicator is on.
If the “READY” indicator changes from a flashing light to a
solid light and the buzzer sounds, the hybrid system is starting
normally.
The vehicle will not move when the “READY” indicator is
off.
The vehicle can move when the “READY” indicator is on
even if the engine is stopped. (The gasoline engine starts or
stops automatically in accordance with the state of the vehi-
cle.)
Stopping the hybrid system
Stop the vehicle completely.
Set the parking brake. (P. 217)
Shift the shift position to P. (P. 2 1 0 )
Check that the shift position indicator shows P. (P. 207)
Press the “POWER” switch.
The hybrid system will stop, and the meter display will be
extinguished (the shift position indicator will be extinguished
a few seconds after the meter display)
STEP4
STEP1
STEP2
STEP3
STEP4