ECO mode Lexus CT200h 2012 (in English) Workshop Manual

588
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)*
1: Rear passengers’ seat belt buzzer
The rear passengers’ seat belt buzzer sounds to alert the driver that the
rear seat belt is not fastened. The buzzer sounds for 30 seconds after the
vehicle reaches a speed of 20 km/h (12 mph). Then, if the seat belt is still
unfastened, the buzzer will sound in a different tone for 90 more seconds.
*2: For the EV drive mode operating conditions (P. 204).
Warning messageDetailsCorrection procedure
(Flashes 3
times)
Indicates that the EV
drive mode has been
automatically can-
celled
*2
The reason the EV
drive mode is not
available (the battery
charge is low, speed is
higher than the EV
drive mode speed
range, accelerator
pedal is depressed too
much) may be dis-
played.
Drive the vehicle for a
while.

5
597
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Once
(Flashes)
The driver’s
door was opened
and closed with
the “POWER”
switch turned
off and then the
“POWER”
switch was put
in ACCES-
SORY mode
twice without
the hybrid sys-
tem being
started.
Press the
“POWER”
switch while
depressing the
brake pedal.
During a hybrid
system starting
procedure in the
event that the
electronic key
was not func-
tioning properly
(P. 630), the
“POWER”
switch was
touched with the
electronic key.
Press the
“POWER”
switch within 10
seconds of the
buzzer sound-
ing.

628
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
Emergency start function
When the hybrid system does not start, the following steps can be
used as an interim measure to start the hybrid system if the
“POWER” switch is functioning normally:
Set the parking brake.
Turn the “POWER” switch to ACCESSORY mode.
Press and hold the “POWER” switch for about 15 seconds
while depressing the brake pedal firmly.
Even if the hybrid system can be started using the above steps, the
system may be malfunctioning. Have the vehicle inspected by any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
The interior lights and headlights do not turn on, or the horn
does not sound.
One of the following may be the cause of the problem:
One or both of the 12-volt battery terminals may be discon-
nected.
The 12-volt battery may be discharged. (P. 508)
Contact any authorized Lexus dealer or repairer, or another duly
qualified and equipped professional if the problem cannot be
repaired, or if repair procedures are unknown.
STEP1
STEP2
STEP3

632
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
Stopping the hybrid system
Set the parking brake, shift the shift position to P and press the “POWER”
switch as you normally do when stopping the hybrid system.
Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the
electronic key battery be replaced immediately when the battery is depleted.
(P. 527)
Alarm (if equipped)
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set,
the alarm may be triggered. (P. 142)
Changing “POWER” switch modes
Within 10 seconds of the buzzer sounding, release the brake pedal and press
the “POWER” switch.
The hybrid system does not start and modes will be changed each time the
switch is pressed.(P. 200)

5
635
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)
Start the engine of the second vehicle. Increase the
engine speed slightly and maintain at that level for
approximately 5 minutes to recharge the battery of your
vehicle.
Open and close any of the doors of your vehicle with the
“POWER” switch off.
Maintain the engine speed of the second vehicle and start
the hybrid system of your vehicle by turning the
“POWER” switch to ON mode.
Make sure the “READY” indicator light comes on. If the
indicator light does not come on, contact any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
Once the hybrid system has started, remove the jumper
cables in the exact reverse order from which they were
connected.
To install the engine cover, conduct the removal proce-
dure in reverse. After installing, check that the fixed pins
are inserted securely.
Once the hybrid system starts, have the vehicle inspected at any
th i d L d l i th d l lifi dSTEP4
STEP5
STEP6
STEP7
STEP8
STEP9

682
6-2. Customization
CT200h_OM_OM76067E_(EE)
Automatic
air condi-
tioning
system
(P. 318)
Efficient ven-
tilation mode
(Switching
between out-
side air and
recirculated air
mode linked to
“AUTO”
switch opera-
tion)*
4
OnOffO––O
AUTO A/C
MODE
(Enable/dis-
able auto-
matic
operation of
the air condi-
tioning com-
pressor when
the “AUTO”
switch ON)
OffOnO–OO
Heating/cool-
ing operation
minimized in
Eco drive
mode
OnOff–––O
ItemFunctionDefault
settingCustomized
setting

695
Alphabetical index
CT200h_OM_OM76067E_(EE)
Electric power steering ..............291
Electronic key
If the electronic key does not
operate properly .................630
Replacing battery ..................527
Emergency, in case of
If a warning buzzer sounds ...571
If a warning light turns on ....571
If a warning message is
displayed ............................578
If the electronic key does not
operate properly .................630
If the hybrid system will not
start .....................................627
If the 12-volt battery is
discharged ..........................633
If you have a flat tire ...599, 613
If you lose your keys ............629
If you think something is
wrong .................................570
If your vehicle becomes stuck ....
644
If your vehicle has to be stopped
in an emergency .................646
If your vehicle needs to be
towed ..................................563
If your vehicle overheats ......639
Emergency brake signal ............292
Emergency flashers ...................562Engine
Accessory mode................... 200
Compartment ....................... 496
Hood .................................... 492
How to start the hybrid
system................................ 198
Identification number .......... 651
If the hybrid system will not
start .................................... 627
Ignition switch ..................... 198
Overheating ......................... 639
“POWER” switch ................ 198
Engine compartment cover....... 497
Engine coolant
Capacity ............................... 657
Checking .............................. 503
Preparing and checking
before winter ..................... 311
Engine/power control unit coolant
Capacity ............................... 657
Checking .............................. 503
Preparing and checking
before winter ..................... 311E
*: For vehicles with a navigation system, refer to
the “Navigation System Owner’s Manual”.