remote start Lexus CT200h 2017 (in English) User Guide

CT200h_OM_OM76215U_(U)
1193-2. Opening, closing and locking the doors
3
Operation of each component
●If the electronic key is insi de the vehicle and a door handle becomes wet during a car
wash, a message may be shown on the multi-information display and a buzzer will
sound outside the vehicle. To turn off the alarm, lock all the doors.
●The lock sensor may not work properly if it comes into contact with ice, snow, mud, etc.
Clean the lock sensor and attempt to operate it again, or use the lock sensor on the
lower part of the door handle.
●A sudden approach to the effective range or door handle may prevent the doors from
being unlocked. In this case, return the door handle to the original position and check
that the doors unlock before pulling the door handle again.
●If there is another electronic key in the detection area, it may take slightly longer to
unlock the doors after the door handle is gripped.
●Fingernails may scrape against the door duri ng operation of the door handle. Be care-
ful not to injure fingernails or damage the surface of the door.
■When the vehicle is not driven for extended periods
●To prevent theft of the vehicle, do not leave the electronic key within 6 ft. (2 m) of the
vehicle.
●The smart access system with push-button start can be deactivated in advance.
(  P. 5 9 8 )
■To operate the system properly
Make sure to carry the electronic key when operating the system. Do not get the elec-
tronic key too close to the vehicle when op erating the system from the outside of the
vehicle.
Depending on the position and holding condition of the electronic key, the key may not
be detected correctly and the system may not operate properly. (The alarm may go off
accidentally, or the door lock prevention may not operate.)
■If the smart access system with push-button start does not operate properly
●Locking and unlocking the doors: Use the mechanical key. (P. 566)
●Starting the hybrid system: P. 5 6 7
■Customization
Settings (e.g. smart access system with push-button start) can be changed.
(Customizable features: P. 5 9 8 )
■If the smart access system with push-butto n start has been deactivated in a customized
setting
●Locking and unlocking the doors:
Use the wireless remote control or mechanical key. ( P. 107, 566)
●Starting the hybrid system and changing power switch modes: P. 5 6 7
●Stopping the hybrid system: P. 1 6 0

128
CT200h_OM_OM76215U_(U)3-3. Adjusting the seats
■Recall procedure
Carry the electronic key that has been
registered to the driving position, and
then unlock and open the driver’s door using the smart access system with
push-button start or wireless remote control.
The driving position will move to the recorded position.
If the driving position is in a position that has already been recorded, the seat and out-
side rear view mirrors will not move.
■Cancelation procedure
Carry only the key you want to cancel and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be canceled
properly.
Turn the power switch to ON mode.
While pressing the “SET” button, press and hold the door lock switch
(either lock or unlock) unt il the buzzer sounds twice.
If the button could not be canceled, the buzzer sounds continuously for approxi-
mately 3 seconds.
■Recalling the driving position using the memory recall function
●Different driving positions can be registered for each electronic key. Therefore, the
driving position that is recalled may be different depending on the key being carried.
●If a door other than the driver’s door is unlocked with the smart access system with
push-button start, the driving position cannot be recalled. In this case, press the driving
position button which has been set.
WA R N I N G
■Seat adjustment caution
Take care during seat adjustment so that th e seat does not strike the rear passenger or
squeeze your body against the steering wheel.
1
2

140
CT200h_OM_OM76215U_(U)3-5. Opening, closing the windows and moon roof
■The power windows can be operated when
The power switch is in ON mode.
■Operating the power windows after turning the hybrid system off
The power windows can be operated for approximately 45 seconds even after the
power switch is turned to ACCESSORY mode or turned off. They cannot, however, be
operated once either front door is opened.
■Jam protection function
If an object becomes jammed between the wi
ndow and the window frame while the win-
dow is closing, window movement is stop ped and the window is opened slightly.
■Catch protection function
If an object becomes caught between the door and window while the window is opening,
window movement is stopped.
■When the window cannot be opened or closed
When the jam protection function or catch protection function operates unusually and
the door window cannot be open ed or closed, perform the following operations with the
power window switch of that door.
●Stop the vehicle. With the power switch in ON mode, within 4 seconds of the jam pro-
tection function or catch protection func tion activating, continuously operate the
power window switch in the one-touch closing direction or one-touch opening direc-
tion so that the door window can be opened and closed.
●If the door window cannot be opened and closed even when performing the above
operations, perform the following proc edure for function initialization.
Turn the power switch to ON mode.
Pull and hold the power window switch in the one-touch closing direction and com-
pletely close the door window.
Release the power window switch for a moment, resume pulling the switch in the one-
touch closing direction, and hold it th ere for approximately 6 seconds or more.
Press and hold the power window switch in the one-touch opening direction. After the
door window is completely op ened, continue holding the swit ch for an additional 1 sec-
ond or more.
Release the power window switch for a mo ment, resume pushing the switch in the
one-touch opening direction, and hold it there for approximately 4 seconds or more.
Pull and hold the power window switch in the one-touch closing direction again. After
the door window is completely closed, continue holding the switch for a further 1 sec-
ond or more.
If you release the switch while the window is moving, start again from the beginning.
If the window reverses and cannot be fully cl osed or opened, have the vehicle inspected
by your Lexus dealer.
■Door lock linked window operation
●The power windows can be opened an d closed using the mechanical key.* ( P. 5 6 6 )
●The power windows can be opened us ing the wireless remote control.* (P. 1 0 7 )
*: These settings must be customized at your Lexus dealer.
■Customization
Setting (e.g. linked door lock operation) can be changed.
(Customizable features:
P. 5 9 8 )
1
2
3
4
5
6

CT200h_OM_OM76215U_(U)
4496-4. Using the other interior features
6
Interior features
Programming an entry gate (for U.S.A. owners)/Programming a device in
the Canadian market
With one hand, press and hold the HomeLink
® button you want to pro-
gram. With your other hand, press and release the remote control transmit-
ter every 2 seconds and repeat this cycle until the HomeLink
® indicator
light starts to flash rapidly. Then, release the buttons.
Te s t t h e H o m e L i n k
® operation by pressing the newly programmed button
and observing the indicator light:
●If the indicator light is solid/con tinuous, programming has been com-
pleted and your device shou ld activate when the HomeLink® button is
pressed and released.
●If the indicator light blinks rapidly for 2 seconds and then turns into a
solid/continuous light, proceed to the heading “Programming a Rolling
Code System”.
Repeat the steps above to program another device for any of the remaining
HomeLink
® buttons.
■Programming a Rolling Code System
Locate the “learn” or “smart” but-
ton on the garage door opener
motor in the garage.
This button can usually be found
where the hanging antenna wire is
attached to the unit. The name and
color of the button may vary by man-
ufacturer. Please refer to the
Owner’s manual supplied with the
garage door opener motor for
details.
Press and release the “learn” or
“smart” button.
Perform step within 30 sec-
onds after performing step .
2
3
4
1
2
3
2

CT200h_OM_OM76215U_(U)
4937-3. Do-it-yourself maintenance
7
Maintenance and care
■Before recharging
When recharging, the 12-volt battery produces hydrogen gas which is flammable and
explosive. Therefore, observe the following precautions before recharging:
●If recharging with the 12-volt battery installed on the vehicle, be sure to disconnect the
ground cable.
●Make sure the power switch on the charger is off when connecting and disconnecting
the charger cables to the 12-volt battery.
■After recharging/reconnecting the 12-volt battery
●Unlocking the doors using the smart access system with push-button start may not be
possible immediately after reconnecting the 12-volt battery. If this happens, use the
wireless remote control or the mech anical key to lock/unlock the doors.
●Start the hybrid system with the power switch in ACCESSORY mode. The hybrid sys-
tem may not start with the power switch turned off. However, the hybrid system will
operate normally from the second attempt.
●The power switch mode is recorded by the vehicle. If the 12-volt battery is reconnected,
the vehicle will return the power switch mode to the status it was in before the 12-volt
battery was disconnected. Make sure to turn off the power before disconnect the 12-
volt battery. Take extra care when connecting the 12-volt battery if the power switch
mode prior to discharge is unknown.
●Restart the hybrid system, depress the brake pedal, and confirm that it is possible to
shift into each shift position.
If the system will not start even after multiple attempts at all methods above, contact your
Lexus dealer.
WA R N I N G
■Chemicals in the 12-volt battery
The 12-volt battery contains poisonous and corrosive sulfuric acid and may produce
hydrogen gas which is flammable and explosive. To reduce the risk of death or serious
injury, take the following precautions while working on or near the 12-volt battery:
●Do not cause sparks by touching the 12-volt battery terminals with tools.
●Do not smoke or light a match near the 12-volt battery.
●Avoid contact with eyes, skin and clothes.
●Never inhale or swallow electrolyte.
●Wear protective safety glasses when working near the 12-volt battery.
●Keep children away from the 12-volt battery.
■Where to safely charge the 12-volt battery
Always charge the 12-volt battery in an open area. Do not charge the 12-volt battery in
a garage or closed room where there is insufficient ventilation.
■How to recharge the 12-volt battery
Only perform a slow charge (4.2 A or less). The 12-volt battery may explode if charged
at a quicker rate.

510
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
■Use a CR1632 lithium battery
●Batteries can be purchased at your Lexus
dealer, local electrical appliance shops or
camera stores.
●Replace only with the same or equivalent type recommended by the manufacturer.
●Dispose of used batteries according to the local laws.
■When the card key battery needs to be replaced (if equipped)
The battery for the card key is available only at Lexus dealers. Your Lexus dealer can
replace the battery for you.
■If the electronic key battery is depleted
The following symptoms may occur:
●The smart access system with push-button start and wireless remote control will not
function properly.
●The operational range will be reduced.
WA R N I N G
■Removed battery and other parts
These parts are small and if swallowed by a child, they can cause choking. Keep away
from children. Failure to do so could result in death or serious injury.
NOTICE
■For normal operation afte r replacing the battery
Observe the following precautions to prevent accidents:
●Always work with dry hands.
Moisture may cause the battery to rust.
●Do not touch or move any other component inside the remote control.
●Do not bend either of the battery terminals.

566
CT200h_OM_OM76215U_(U)8-2. Steps to take in an emergency
If the electronic key do
es not operate properly
Use the mechanical key ( P. 1 0 3 ) i n
order to perform the following opera-
tions:
Locks all the doors
Closes the windows
* (turn and hold)
Unlocks the door
Turning the key rearward unlocks the
driver’s door. Turning the key once again
within 3 seconds unlocks the other
doors.
Opens the windows* (turn and hold)
*: These settings must be cust omized at your Lexus dealer.
If communication between the electron ic key and vehicle is interrupted
(  P. 117) or the electronic key cannot be used because the battery is
depleted, the smart access system with push-button start and wireless
remote control cannot be used. In such cases, the doors can be opened and
the hybrid system can be started by following the procedure below.
Locking and unlocking the doors and key linked functions
1
2
3
4

600
CT200h_OM_OM76215U_(U)9-2. Customization
■Smart access system with push-button start and wireless remote control
(
 P. 116, 102)
■Smart access system with push-button start ( P. 116)
FunctionDefault
settingCustomized setting
Operation signal (buzzer) 7 Off
O–OO
1 to 6
Operation signal (emer-
gency flashers) On Off O – O O
Time elapsed before the
automatic door lock func-
tion is activated if a door is
not opened after being
unlocked
60 seconds
Off
O–OO30 seconds
120 seconds
Open door reminder
buzzer (When locking the
vehicle)
OnOff–––O
1234
FunctionDefault
settingCustomized setting
Smart door unlocking Driver’s door All the doors O – O O
Smart access system with
push-button startOnOffO–OO
Number of consecutive
door lock operations2 timesAs many as desired–––O
1234

602
CT200h_OM_OM76215U_(U)9-2. Customization
■Illumination (
P. 4 3 1 )
*: Interior or exterior illumination can be set separately.
FunctionDefault
settingCustomized setting
Time elapsed before the
interior lights turn off 15 secondsOff
O–OO
7. 5 s e c o n d s
30 seconds
Time elapsed before the
exterior lights turn off15 seconds
Off
O–OO7. 5 s e c o n d s
30 seconds
Operation after the power
switch is turned offOnOff–––O
Operation when the doors
are unlocked with the smart
access system with push-
button start or the wireless
remote control function or
the mechanical key
*
OnOff–––O
Operation when you
approach the vehicle with
the electronic key on your
person
*
OnOff–––O
Footwell lightingOnOff–––O
Cup holder lightOnOff–––O
Enable/disable operation of
the outer foot lights when
the doors are unlocked with
the power door lock switch
OnOff–––O
1234

629Alphabetical index
CT200h_OM_OM76215U_(U)
JackPositioning a floor jack ....................482
Vehicle-equipped jack .................. 556
Jack handle ............................................. 556
Jam protection function Moon roof .............................................. 143
Power windows ................................... 140
Keyless entry Smart access system with push-button start ............................... 116
Wireless remote control ................. 102
Keys............................................................. 102 Electronic key ....................................... 102
Engine switch ........................................ 159
If the electronic key does not operate properly............................ 566
If you lose your keys ............... 104, 106
Key number plate ............................... 102
Keyless entry ......................................... 102
Mechanical key .................................... 102
Power switch......................................... 159
Replacing the battery ...................... 509
Warning buzzer .................................... 117
Wireless remote control key ........ 102
Knee airbags ............................................. 40 Language (multi-information
display) .................................................. 603
LATCH anchors ...................................... 58
Lever Auxiliary catch lever ........................ 480
Hood lock release lever................ 480
Shift lever .................................................165
Turn signal lever ...................................170
Wiper lever............................................. 177
Lexus Display Audio controller .............. 93, 209, 416
Lexus parking assist monitor Display..................................................... 223
Function ...................................................222
Precautions ........................................... 229
License plate lights Light switch............................................. 172
Replacing light bulbs ....................... 524
Light Fog light switch ..................................... 175
Headlight switch .................................. 172
Illuminated entry system................. 432
Interior lights ........................................ 432
Interior light list ...................................... 431
Luggage compartment light ............113
Personal lights ....................................... 431
Replacing light bulbs .........................514
Turn signal lever ...................................170
Vanity lights .......................................... 443
Wattage ................................................ 585
Light bulbs Replacing .................................................514
Wattage ................................................ 585
Luggage cover ...................................... 440
J
K
L