torque LEXUS ES300 2005 Repair Manual
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 414 of 969
A86570
From Canister
Vacuum Tank
Actuator Actuator
Vacuum Surge
TankVSV for EVAP
VSV for ACIS
Engine Mounting
Insulator FR
VSV for Active Control
Engine MountCapVSV Vacuum Hose Routing Diagram:
14-38
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2130 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
140. CONNECT TRANSMISSION CONTROL CABLE ASSY (See page 40-44)
141. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (See page 17-9)
142. INSTALL GENERATOR BELT ADJUSTING BAR (See page 17-9)
143. INSTALL GENERATOR BRACKET NO.2 (See page 14-79)
144. INSTALL ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
145. INSTALL ENGINE MOVING CONTROL ROD (See page 14-79)
146. INSTALL GENERATOR ASSY (See page 19-21)
147. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
148. INSPECT DRIVE BELT DEFLECTION AND TENSION (See page 14-1)
149. INSTALL INTAKE AIR RESONATOR SUB-ASSY
Torque: 5.0 NVm (51 kgfVcm, 44 in.Vlbf)
150. INSTALL AIR CLEANER INLET NO.1 (See page 19-5)
151. INSTALL AIR CLEANER BRACKET (See page 19-5)
152. INSTALL AIR CLEANER ASSY (See page 19-5)
153. INSTALL AIR CLEANER INLET ASSY (See page 19-5)
154. CHECK CONNECTION OF VACUUM HOSE
155. INSTALL V-BANK COVER SUB-ASSY (See page 10-1 1)
156. INSTALL FRONT WHEELS (See page 14-5)
Page 419 of 969
A78535
A78706Align
A78707
Main GearSub Gear
Service Bolt
A78708
101
2
3
4
5
6
7
89
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-43
2135 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
26. REMOVE WATER PUMP ASSY
(a) Remove the 3 bolts and 3 nuts, then remove the water
pump and gasket.
27. REMOVE CAMSHAFT
NOTICE:
Since the thrust clearance of the camshaft is small, the
camshaft must be kept level while being removed. If the
camshaft is not kept level, the cylinder head or camshaft
may be damaged. To avoid this, the following steps must
be carried out.
(a) Align the timing marks (2 dot marks) of the camshaft drive
and driven gears by turning the camshaft with a wrench.
(b) Secure the exhaust camshaft sub gear to the main gear
with a service bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
Recommended service bolt
Thread diameter6 mm
Thread pitch1.0 mm
Bolt length16 to 20 mm
HINT:
When removing the camshaft, make certain that the torsional
spring force of the sub gear has been eliminated by installation
of the service bolt.
(c) Using several steps, loosen and remove the 10 bearing
cap bolts uniformly in the sequence shown in the illustra-
tion. Remove the 5 bearing caps and camshaft.
NOTICE:
Do not pry out the camshaft.
Be careful not to damage the contact surface of the
cylinder head that receives the shaft thrust.
Page 420 of 969
A78709
10
1
2
3
4
5
67
8
9
A78710Align
A78711Main GearSub Gear
Service Bolt 14-44
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2136 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
28. REMOVE NO.2 CAMSHAFT
(a) Using several steps, loosen and remove the 10 bearing
cap bolts uniformly in the sequence shown in the illustra-
tion. Remove the 5 bearing caps and No. 2 camshaft.
NOTICE:
Do not pry out the camshaft.
Be careful not to damage the contact surface of the
cylinder head that receives the shaft thrust.
(b) Remove the oil seal from the No. 2 camshaft.
29. REMOVE NO.3 CAMSHAFT SUB-ASSY
NOTICE:
Since the thrust clearance of the camshaft is small, the
camshaft must be kept level while being removed. If the
camshaft is not kept level, the cylinder head or camshaft
may be damaged. To avoid this, the following steps must
be carried out.
(a) Align the timing marks (1 dot marks) of the camshaft drive
and driven gears by turning the camshaft with a wrench.
(b) Secure the exhaust camshaft sub gear to the main gear
with a service bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
Recommended service bolt
Thread diameter6 mm
Thread pitch1.0 mm
Bolt length16 to 20 mm
HINT:
When removing the camshaft, make certain that the torsional
spring force of the sub gear has been eliminated by installation
of the service bolt.
Page 429 of 969
A78722
SST
A78723
SST
A78724
Seal Width 2 to 3 mm (0.08 to 0.12 in.)
A
A
B
B
A78754
SST
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-53
2145 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
56. INSTALL SPARK PLUG TUBE GASKET
(a) Using SST and a hammer, tap in the new gasket until its
surface is flush with the upper edge of the cylinder head
cover.
SST 09950- 60010 (09951- 00430), 09950- 70010
(09951-07100)
(b) Return the ventilation plate tab to its original position.
(c) Apply a light coat of multi-purpose grease to the gasket
lip.
57. INSTALL ENGINE REAR OIL SEAL
(a) Using SST and a hammer, tap in the new oil seal until its
surface is flush with the rear oil seal retainer edge.
SST 09223-15030, 09950-70010 (09951-07100)
NOTICE:
Be careful not to tap the oil seal at an angle.
Keep the lip free of foreign objects.
(b) Apply multi-purpose grease to the oil seal lip.
58. INSTALL ENGINE REAR OIL SEAL RETAINER
(a) Remove any old packing material from the contact sur-
face.
(b) Apply a continuous bead of seal packing (Diameter 2 to
3 mm (0.08 to 0.12 in.)) as shown in the illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
Remove any oil from the contact surface.
Install the oil seal retainer within 3 minutes after ap-
plying seal packing.
Do not expose the seal packing to engine oil within 2
hours after installing.
(c) Install the oil seal retainer with the 6 bolts. Tighten the
bolts uniformly in several steps.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
59. INSTALL OIL PUMP SEAL
(a) Using SST and a hammer, tap in the new oil seal until its
surface is flush with the oil pump body edge.
SST 09223-00010
NOTICE:
Be careful not to tap the oil seal at an angle.
Keep the lip free of foreign objects.
(b) Apply multi-purpose grease to the oil seal lip.
Page 431 of 969
A51990
AB
C
B
A
AA
A
A
A78726
Seal Packing
Seal Width
3 to 4 mm
(0.12 to 0.16 in.) AAB
B Region ºXº Region ºYº
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-55
2147 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(e) Install the oil pump with the 9 bolts. Tighten the bolts uni-
formly in several steps.
Torque:
8.0 NVm (82 kgfVcm, 71 in.Vlbf) for bolt A
20 NVm (199 kgfVcm, 14 ftVlbf) for bolt B
43 NVm (439 kgfVcm, 32 ftVlbf) for bolt C
61. INSTALL CRANKSHAFT POSITION SENSOR
Torque: 8.0 NVm (80 kgfVcm, 71 in.Vlbf)
62. INSTALL OIL PAN BAFFLE PLATE
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
63. INSTALL OIL PAN SUB-ASSY
(a) Remove any old seal packing from the contact surface.
(b) Apply a continuous bead of seal packing (Diameter 3 to
4 mm (0.12 to 0.16 in.)) as shown in the illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
Remove any oil from the contact surface.
Apply seal packing to the outer side of the bolt holes
in the region ºXº.
Apply seal packing to the inner side of the bolt holes
in the region ºYº.
Install the oil pan within 3 minutes after applying seal
packing.
Do not expose the seal packing to engine oil within 2
hours after installing.
(c) Install the oil pan with the 15 bolts and 2 nuts. Tighten the
bolts uniformly in several steps.
Torque:
8.0 NVm (82 kgfVcm, 71 in.Vlbf) for 10 mm head
20 NVm (199 kgfVcm, 14 ftVlbf) for 12 mm head
64. INSTALL OIL STRAINER SUB-ASSY
(a) Install a new gasket and the oil strainer with the bolt and 2 nuts.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
65. INSTALL OIL PAN SUB-ASSY NO.2
(a) Remove any old seal packing from the contact surface.
Page 432 of 969
A78727
Seal Packing
Seal Width
4 to 5 mm
(0.16 to 0.20 in.) AA
BB
A78728
Seal PackingSeal Width 3 to 5 mm
(0.12 to 0.20 in.)
A78314
10
1
2
3
4
5
6
78
9 14-56
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2148 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(b) Apply a continuous bead of seal packing (Diameter 4 to
5 mm (0.16 to 0.20 in.)) as shown in the illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
Remove any oil from the contact surface.
Apply seal packing to the inner side of the bolt holes.
Install the oil pan within 3 minutes after applying seal
packing.
Do not expose the seal packing to engine oil within 2
hours after installing.
(c) Install the oil pan No. 2 with the 10 bolts and 2 nuts.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
66. INSTALL OIL PAN DRAIN PLUG
(a) Install the drain plug with a new gasket.
Torque: 45 NVm (459 kgfVcm, 33 ftVlbf)
67. INSTALL WATER INLET HOUSING
(a) Remove any old packing material from the contact sur-
face.
(b) Apply a continuous bead of seal packing (Diameter 3 to
5 mm (0.12 to 0.20 in.)) as shown in the illustration.
Seal packing: Part No. 08826-00100 or equivalent
NOTICE:
Remove any oil from the contact surface.
Install the water inlet housing within 3 minutes after
applying seal packing.
Do not expose the seal packing to coolant within 2
hours after installing.
(c) Install the water inlet housing with the 8 bolts and 2 nuts.
Using several steps, tighten the bolts and nuts uniformly
in the sequence shown in the illustration.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
Page 433 of 969
A78324
Front
A78717
1
2
3
4
5
67
8
Front
A78730
90
Front
Painted Mark
A78716
Front
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-57
2149 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
68. INSTALL CYLINDER HEAD GASKET
(a) Place a new cylinder head gasket on the cylinder block
with the R mark upward.
NOTICE:
Remove any oil from the contact surface.
Be careful of the installing orientation.
Place the cylinder head on the gasket carefully in or-
der not to damage the gasket at the bottom part of the
head.
69. INSTALL CYLINDER HEAD SUB-ASSY
NOTICE:
The cylinder head bolts are tightened in 2 successive
steps.
(a) Apply a light coat of engine oil to the threads of the cylin-
der head bolts.
(b) Install the plate washers to the cylinder head bolts.
(c) Using several steps, install and tighten the 8 cylinder
head bolts uniformly in the sequence shown in the illustra-
tion.
Torque: 54 NVm (550 kgfVcm, 40 ftVlbf)
(d) Mark the front side of each cylinder head bolt head with
paint as shown in the illustration.
(e) Retighten the cylinder head bolts by 90in the same se-
quence as step (c).
(f) Check that each painted mark is now at a 90 angle to the
front.
(g) Using a socket hexagon wrench 8, install the hexagon
bolt.
Torque: 19 NVm (189 kgfVcm, 14 ftVlbf)
Page 434 of 969
A79822
Front
A78719
1
2
3
4
5
67
8
Front
A78730
90
Front
Painted Mark
A78718
Front 14-58
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2150 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
70. INSTALL CYLINDER HEAD GASKET NO.2
(a) Place a new cylinder head gasket on the cylinder block
with the L mark upward.
NOTICE:
Remove any oil from the contact surface.
Be careful of the installing orientation.
Place the cylinder head on the gasket carefully in or-
der not to damage the gasket at the bottom part of the
head.
71. INSTALL CYLINDER HEAD LH
NOTICE:
The cylinder head bolts are tightened in 2 successive
steps.
(a) Apply a light coat of engine oil to the threads of the cylin-
der head bolts.
(b) Install the plate washers to the cylinder head bolts.
(c) Using several steps, install and tighten the 8 cylinder
head bolts uniformly in the sequence shown in the illustra-
tion.
Torque: 54 NVm (550 kgfVcm, 40 ftVlbf)
(d) Mark the front side of each cylinder head bolt head with
paint as shown in the illustration.
(e) Retighten the cylinder head bolts by 90 in the same se-
quence as step (c).
(f) Check that each painted mark is now at a 90 angle to the
front.
(g) Using a socket hexagon wrench 8, install the hexagon
bolt.
Torque: 19 NVm (189 kgfVcm, 14 ftVlbf)
Page 435 of 969
A05418
P12595
A78732
Camshaft
Sub Gear
Camshaft Gear
Bolt Washer Wave Washer
A52353
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-59
2151 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
72. INSTALL OIL CONTROL VALVE FILTER
(a) Check that no foreign object is on the mesh part of the fil-
ter.
(b) Assemble the valve filter and plug.
(c) Install the plug with a new gasket.
Torque: 45 NVm (459 kgfVcm, 33 ftVlbf)
73. INSTALL CYLINDER HEAD COVER REAR
(a) Install the rear cover and a new gasket.
Torque: 10 NVm (102 kgfVcm, 7 ftVlbf)
74. INSTALL CAMSHAFT SUB GEAR
(a) Clamp the camshaft in a vise on the hexagonal lobe.
NOTICE:
Be careful not to damage the camshaft.
(b) Install the camshaft gear bolt washer and camshaft sub
gear.
HINT:
Attach the pins on the gears to the gear bolt washer ends.
(c) Install the wave washer.
(d) Using snap ring pliers, install the snap ring.
Page 436 of 969
A78733
SST
A78734
Align
A05738
14-60
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2152 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(e) Using SST, align the holes of the camshaft main gear and
sub gear by turning the camshaft sub gear counterclock-
wise, then temporarily install a service bolt.
SST 09960-10010 (09962-01000, 09963-00500)
(f) Align the gear teeth of the main gear and sub gear, then
tighten the service bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
NOTICE:
Be careful not to damage the camshaft journals.
HINT:
When installing the camshaft, make certain that the torsional
spring force of the sub gear has been eliminated by installation
of the service bolt.
75. INSTALL CAMSHAFT TIMING GEAR ASSY
(a) Align the alignment pin with the alignment pin groove,
then install the VVT-i into the camshaft.
NOTICE:
Install it with the lock pin engaged and locked at the most
retard angle position.
(b) Apply engine oil to the nut, mounting surface of the VVT-i
and screw threads.
NOTICE:
Be sure to apply the oil, otherwise the specified
torque cannot be obtained.
New nuts must be used when replacing the VVT-i
unit.
(c) Using a 46 mm socket wrench, install and tighten a lock
nut by turning it counterclockwise.
Torque: 150 NVm (1,530 kgfVcm, 111 ftVlbf)
NOTICE:
The lock nut has LH threads.
Never use any tools other than the socket wrench.
Other tools will deform the cam angle rotor.
76. INSTALL NO.2 CAMSHAFT
NOTICE:
Since the thrust clearance of the camshaft is small, the
camshaft must be kept level while being installed. If the
camshaft is not kept level, the cylinder head or camshaft
may be damaged. To avoid this, the following steps must
be carried out.
(a) Apply new engine oil to the thrust portion and journal of
the camshaft.