belt LEXUS ES300 2005 Manual PDF
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 506 of 969
A78384N´m (kgf´cm, ft´lbf)
: Specified torque
8.5 (87, 75 in.Vlbf)
43 (438, 32)
Timing Belt Idler
Sub-assy No. 2x6Timing Belt No. 3 Cover
CollarGasket
Bushing
Camshaft Timing Pulley
125 (1,275, 92)
Engine Wire
14-130
- ENGINE MECHANICALCYLINDER HEAD GASKET NO.2 (3MZ-FE)
2222 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
Page 509 of 969
141JJ-01
A86574
- ENGINE MECHANICALCYLINDER HEAD GASKET NO.2 (3MZ-FE)
14-133
2225 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. DISCHARGE FUEL SYSTEM PRESSURE (See page 11-1)
2. DISCONNECT BATTERY NEGATIVE TERMINAL
3. DRAIN ENGINE COOLANT (See page 16-9)
4. DRAIN ENGINE OIL (See page 17-20)
5. REMOVE FRONT WHEEL RH
6. REMOVE RADIATOR LOWER AIR DEFLECTOR (See page 19-5)
7. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS) (See page 10-1 1)
8. REMOVE V-BANK COVER SUB-ASSY (See page 10-1 1)
9. REMOVE AIR CLEANER INLET ASSY (See page 19-5)
10. REMOVE AIR CLEANER CAP SUB-ASSY (See page 10-1 1)
11. REMOVE AIR CLEANER CASE (See page 19-5)
12. REMOVE EMISSION CONTROL VALVE SET (See page 11-13)
13. REMOVE INTAKE AIR SURGE TANK (See page 11-13)
14. REMOVE INTAKE MANIFOLD (See page 10-16)
15. REMOVE WATER OUTLET (See page 10-16)
16. REMOVE FRONT FENDER APRON SEAL RH
17. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
18. REMOVE VANE PUMP V BELT (See page 14-5)
19. REMOVE ENGINE MOVING CONTROL ROD (See page 14-79)
20. REMOVE ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
21. REMOVE GENERATOR BRACKET NO.2 (See page 14-79)
22. REMOVE CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021, 09950-50013 (09951-05010, 09952-05010,
09953-05020, 09954-05031)
23. REMOVE TIMING BELT NO.1 COVER
24. REMOVE TIMING BELT NO.2 COVER (See page 14-79)
25. REMOVE ENGINE MOUNTING BRACKET RH (See page 14-79)
26. REMOVE TIMING BELT GUIDE NO.2
27. REMOVE TIMING BELT (See page 14-79)
28. REMOVE TIMING BELT IDLER SUB-ASSY NO.2
29. REMOVE CAMSHAFT TIMING PULLEY (See page 14-93)
SST 09960-10010 (09962-01000, 09963-01000), 09249-63010
30. REMOVE TIMING BELT NO.3 COVER (See page 14-93)
31. REMOVE MANIFOLD STAY NO.2 (See page 14-29)
32. SEPARATE EXHAUST PIPE ASSY FRONT (See page 15-2)
33. REMOVE OIL LEVEL GAGE GUIDE
(a) Remove the bolt which secures the oil level gage guide
from the cylinder head LH.
(b) Pull out the oil level gage guide and oil level gage together
from the cylinder block.
(c) Remove the O-ring from the oil level gage guide.
Page 512 of 969
A86573
O-ring
14-136
- ENGINE MECHANICALCYLINDER HEAD GASKET NO.2 (3MZ-FE)
2228 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
49. INSTALL OIL LEVEL GAGE GUIDE
(a) Install a new O-ring to the oil level gage guide.
(b) Apply soapy water to the O-ring.
(c) Push in the oil level gage guide end into the guide hole of
the cylinder block.
(d) Install the oil level gage guide with the bolt.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
(e) Install the oil level gage.
50. INSTALL EXHAUST PIPE ASSY FRONT (See page 15-2)
51. INSTALL MANIFOLD STAY NO.2 (See page 14-29)
52. INSTALL TIMING BELT NO.3 COVER (See page 14-93)
53. INSTALL CAMSHAFT TIMING PULLEY (See page 14-93)
SST 09960-10010 (09962-01000, 09963-01000), 09249-63010
54. INSTALL TIMING BELT IDLER SUB-ASSY NO.2 (See page 14-93)
55. INSPECT TIMING BELT (See page 14-79)
56. INSTALL TIMING BELT (See page 14-79)
SST 09960-10010 (09962-01000, 09963-01000)
57. INSTALL TIMING BELT TENSIONER ASSY (See page 14-79)
58. INSTALL TIMING BELT GUIDE NO.2 (See page 14-79)
59. INSTALL ENGINE MOUNTING BRACKET RH (See page 14-79)
60. INSTALL TIMING BELT NO.2 COVER (See page 14-79)
61. INSTALL TIMING BELT NO.1 COVER (See page 14-79)
62. INSTALL CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021
63. INSTALL GENERATOR BRACKET NO.2 (See page 14-79)
64. INSTALL ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
65. INSTALL ENGINE MOVING CONTROL ROD (See page 14-79)
66. INSTALL VANE PUMP V BELT (See page 14-5)
67. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
68. INSPECT DRIVE BELT DEFLECTION AND TENSION (See page 14-1)
69. INSTALL WATER OUTLET (See page 10-16)
70. INSTALL INTAKE MANIFOLD (See page 10-16)
71. INSTALL INTAKE AIR SURGE TANK (See page 11-13)
72. INSTALL EMISSION CONTROL VALVE SET (See page 11-13)
73. INSTALL AIR CLEANER CASE (See page 19-5)
74. INSTALL AIR CLEANER CAP SUB-ASSY (See page 10-1 1)
75. INSTALL AIR CLEANER INLET ASSY (See page 19-5)
76. CHECK CONNECTION OF VACUUM HOSE (See page 14-29)
77. INSTALL V-BANK COVER SUB-ASSY (See page 10-1 1)
78. INSTALL FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS) (See page 10-1 1)
79. INSTALL FRONT WHEEL RH (See page 14-5)
80. ADD ENGINE OIL (See page 17-20)
81. ADD ENGINE COOLANT (See page 16-9)
82. CHECK FOR ENGINE OIL LEAKS
83. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)
84. INSPECT FOR FUEL LEAKS
Page 514 of 969
141JK-01
A78764SST
A78765
Cut Position 14-138
- ENGINE MECHANICALOIL PUMP SEAL (3MZ-FE)
2230 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
OIL PUMP SEAL (3MZ-FE)
REPLACEMENT
1. REMOVE FRONT WHEEL RH
2. REMOVE FRONT FENDER APRON SEAL RH
3. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
4. REMOVE VANE PUMP V BELT (See page 14-5)
5. REMOVE ENGINE MOVING CONTROL ROD (See page 14-79)
6. REMOVE ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
7. REMOVE GENERATOR BRACKET NO.2 (See page 14-79)
8. REMOVE CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021, 09950-50013 (09951-05010, 09952-05010,
09953-05020, 09954-05031)
9. REMOVE TIMING BELT NO.1 COVER
10. REMOVE TIMING BELT NO.2 COVER (See page 14-79)
11. REMOVE ENGINE MOUNTING BRACKET RH (See page 14-79)
12. REMOVE TIMING BELT GUIDE NO.2
13. REMOVE TIMING BELT (See page 14-79)
14. REMOVE CRANKSHAFT TIMING PULLEY
(a) Remove the bolt and timing belt plate.
(b) Install the pulley bolt to the crankshaft.
(c) Using SST, remove the crankshaft timing pulley.
SST 09950- 50013 (09951- 05010, 09952- 05010,
09953-05020, 09954-05011)
NOTICE:
Do not scratch the sensor part of the crankshaft tim-
ing pulley.
Before using SST, apply lubricating oil to the threads
and tip of the center bolt 150.
15. REMOVE OIL PUMP SEAL
(a) Using a knife, cut off the oil seal lip.
(b) Using a screwdriver with the tip wrapped in tape, pry out
the oil seal.
NOTICE:
After removing, check the crankshaft for damage. If dam-
aged, smooth the surface with 400-grit sandpaper.
Page 515 of 969
A78766
SST
A78746
Inward
Sensor
- ENGINE MECHANICALOIL PUMP SEAL (3MZ-FE)
14-139
2231 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
16. INSTALL OIL PUMP SEAL
(a) Apply multi-purpose grease to a new oil seal lip.
NOTICE:
Keep the lip free of foreign objects.
(b) Using SST and a hammer, tap in the new oil seal until its
surface is flush with the oil pump edge.
SST 09223-00010
NOTICE:
Be careful not to tap the oil seal at an angle.
Wipe off extra grease on the crankshaft.
17. INSTALL CRANKSHAFT TIMING PULLEY
(a) Align the keyway of the pulley with the key located on the
crankshaft, then slide the pulley into place.
NOTICE:
Do not scratch the sensor area of the crankshaft timing
pulley.
(b) Install the timing belt plate with the bolt.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
18. INSPECT TIMING BELT (See page 14-79)
19. INSTALL TIMING BELT (See page 14-79)
SST 09960-10010 (09962-01000, 09963-01000)
20. INSTALL TIMING BELT TENSIONER ASSY (See page 14-79)
21. INSTALL TIMING BELT GUIDE NO.2 (See page 14-79)
22. INSTALL ENGINE MOUNTING BRACKET RH (See page 14-79)
23. INSTALL TIMING BELT NO.2 COVER (See page 14-79)
24. INSTALL TIMING BELT NO.1 COVER (See page 14-79)
25. INSTALL CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021
26. INSTALL GENERATOR BRACKET NO.2 (See page 14-79)
27. INSTALL ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
28. INSTALL ENGINE MOVING CONTROL ROD (See page 14-79)
29. INSTALL VANE PUMP V BELT (See page 14-5)
30. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
31. INSPECT DRIVE BELT DEFLECTION AND TENSION (See page 14-1)
32. INSTALL FRONT WHEEL RH (See page 14-5)
33. CHECK FOR ENGINE OIL LEAKS
Page 659 of 969
160QG-01
A84916
64 (653, 47)
64 (653, 47)
Front Fender Apron
Seal RH
Vane Pump V Belt
V Belt No. 1
Generator Bracket No. 2
Engine Mounting Stay No. 2 RHEngine Moving Control Rod
N´m (kgf´cm, ft´lbf)
: Specified torque
23 (235, 17)
58 (591, 43)
28 (286, 21)
Radio Setting Condenser
16-10
- COOLINGWATER PUMP ASSY (3MZ-FE)
2288 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
WATER PUMP ASSY (3MZ-FE)
COMPONENTS
Page 660 of 969
A78353
N´m (kgf´cm, ft´lbf)
: Specified torque
8.5 (87, 75 in.Vlbf)
220 (2,250, 162)8.5 (87, 75 in.Vlbf)
28 (286, 21)
27 (280, 20)
Timing Belt Tensioner AssyCrankshaft PulleyTiming Belt No. 1 Cover
Timing Belt Guide No. 2
Engine Mounting Bracket RH Timing Belt No. 2 Cover
Timing Belt
Engine Wire
Protector
- COOLINGWATER PUMP ASSY (3MZ-FE)
16-1 1
2289 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
Page 661 of 969
A78394
N´m (kgf´cm, ft´lbf)
: Specified torque
Non-reusable part Water Pump Gasket
8.5 (87, 75 in.Vlbf)
125 (1,275, 92)
43 (438, 32)
8.0 (82, 71 in.Vlbf)
8.0 (82, 71 in.Vlbf)
34 (347, 25)
Timing Belt Idler Sub-assy No. 1Water Pump Assy Timing Belt Idler
Sub-assy No. 2Camshaft Timing
Pulley x6Timing Belt No. 3 Cover
CollarGasket
Bushing
Engine Wire
16-12
- COOLINGWATER PUMP ASSY (3MZ-FE)
2290 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
Page 662 of 969
160QH-01
A78535
- COOLINGWATER PUMP ASSY (3MZ-FE)
16-13
2291 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. DRAIN ENGINE COOLANT (See page 16-9)
2. REMOVE FRONT WHEEL RH
3. REMOVE FRONT FENDER APRON SEAL RH
4. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
5. REMOVE VANE PUMP V BELT (See page 14-5)
6. REMOVE ENGINE MOVING CONTROL ROD (See page 14-79)
7. REMOVE ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
8. REMOVE GENERATOR BRACKET NO.2 (See page 14-79)
9. REMOVE CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021, 09950-50013 (09951-05010, 09952-05010,
09953-05020, 09954-05031)
10. REMOVE TIMING BELT NO.1 COVER
11. REMOVE TIMING BELT NO.2 COVER (See page 14-79)
12. REMOVE ENGINE MOUNTING BRACKET RH (See page 14-79)
13. REMOVE TIMING BELT GUIDE NO.2
14. REMOVE TIMING BELT (See page 14-79)
15. REMOVE TIMING BELT IDLER SUB-ASSY NO.2
16. REMOVE CAMSHAFT TIMING PULLEY (See page 14-93)
SST 09960-10010 (09962-01000, 09963-01000), 09249-63010
17. REMOVE TIMING BELT NO.3 COVER (See page 14-93)
18. REMOVE TIMING BELT IDLER SUB-ASSY NO.1
(a) Using a socket hexagon wrench 10, remove the pivot bolt, timing belt idler No. 1 and plate washer.
19. REMOVE WATER PUMP ASSY
(a) Remove the 3 bolts and 3 nuts, then remove the water
pump and gasket.
20. INSTALL WATER PUMP ASSY
(a) Install a new gasket and the water pump with the 3 bolts and 3 nuts.
Torque: 8.0 NVm (82 kgfVcm,
71 in.Vlbf)
21. INSTALL TIMING BELT IDLER SUB-ASSY NO.1
(a) Using a socket hexagon wrench 10, install the plate washer and timing belt idler No.1 with the pivot
bolt.
Torque: 34 NVm (347 kgfVcm,
25 ftVlbf)
22. INSTALL TIMING BELT NO.3 COVER (See page 14-93)
23. INSTALL CAMSHAFT TIMING PULLEY (See page 14-93)
SST 09960-10010 (09962-01000, 09963-01000), 09249-63010
24. INSTALL TIMING BELT IDLER SUB-ASSY NO.2 (See page 14-93)
25. INSPECT TIMING BELT (See page 14-79)
26. INSTALL TIMING BELT (See page 14-79)
SST 09960-10010 (09962-01000, 09963-01000)
Page 663 of 969
16-14
- COOLINGWATER PUMP ASSY (3MZ-FE)
2292 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
27. INSTALL TIMING BELT TENSIONER ASSY (See page 14-79)
28. INSTALL TIMING BELT GUIDE NO.2 (See page 14-79)
29. INSTALL ENGINE MOUNTING BRACKET RH (See page 14-79)
30. INSTALL TIMING BELT NO.2 COVER (See page 14-79)
31. INSTALL TIMING BELT NO.1 COVER (See page 14-79)
32. INSTALL CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021
33. INSTALL GENERATOR BRACKET NO.2 (See page 14-79)
34. INSTALL ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
35. INSTALL ENGINE MOVING CONTROL ROD (See page 14-79)
36. INSTALL VANE PUMP V BELT (See page 14-5)
37. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
38. INSPECT DRIVE BELT DEFLECTION AND TENSION (See page 14-1)
39. INSTALL FRONT WHEEL RH (See page 14-5)
40. ADD ENGINE COOLANT (See page 16-9)
41. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)