change time lexus LC500 2018 Owner's Guide

264
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Press the switch again to turn the sys-
tems back on.*: On vehicles with PCS (Pre-Collision Sys-
tem), PCS will also be disabled (only Pre-
Collision warning is available). The PCS
warning light will come on and a message
will be displayed on the multi-information
display. ( P.217)
■When the message is displayed on the multi-information display showing that
TRC has been disabled even if the
switch has not been pressed
TRC cannot be operated. Contact any
authorized Lexus retailer or Lexus autho- rized repairer, or any reliable repairer.
■Operating conditions of hill-start assist control
When the following four conditions are met, the hill-start assist control will operate:
●The shift position is in a position other than P or N (when starting off for-
ward/backward on an upward incline).
●The vehicle is stopped.
●The accelerator pedal is not depressed.
●The parking brake is not engaged.
■Automatic system cancelation of hill- start assist control
The hill-start assist control will turn off in any of the following situations:
●The shift position is shifted to P or N.
●The accelerator pedal is depressed.
●The parking brake is engaged.
●2 seconds at maximum elapsed after the brake pedal is released
■VGRS is disabled when
VGRS may stop operating in the following situations.
In this event, the steering wheel may move from its straight forward position, but it will
return when the system restarts.
●When the steering wheel is operated for
an extended period of time while the vehicle is stopped or is moving very slowly (on vehicles with LDH, DRS is dis-
abled together with VGRS)
●When the steering wheel has been held
fully to the left or right
The center position of the steering wheel
may change when VGRS is disabled. How- ever, the position will return to normal after VGRS is reactivated.
■When the 12-volt battery is discon-
nected (vehicles with VGRS)
The steering wheel may move from its
straight forward position, but this will be corrected automatically when driving.
■Sounds and vibrations caused by the ABS, brake assist, TRC, VSC, hill-start
assist control and VGRS systems
●A sound may be heard from the engine
compartment when the brake pedal is depressed repeatedly, when the engine is started or just after the
vehicle begins to move. This sound does not indicate that a malfunction has occurred in any of these systems.
●Any of the following conditions may
occur when the above systems are oper- ating. None of these indicates that a mal-function has occurred.
• Vibrations may be felt through the vehicle body and steering.• A motor sound may be heard after the
vehicle comes to a stop.
■ECB operating sound
ECB operating sound may be heard in the
following cases, but it does not indicate that a malfunction has occurred.
●Operating sound heard from the engine compartment when the brake pedal is operated.
●Motor sound of the brake system heard from the front part of the vehicle when
the driver’s door is opened.
●Operating sound heard from the engine
compartment when one or two minutes passed after the stop of the engine .

266
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
WARNING
■Stopping distance when the ABS is operating may exceed that of normal conditions
The ABS is not designed to shorten the vehicle’s stopping distance. Always main-
tain a safe distance from the vehicle in front of you, especially in the following situations:
●When driving on dirt, gravel or snow-
covered roads
●When driving with tire chains
●When driving over bumps in the road
●When driving over roads with potholes or uneven surfaces
■TRC/VSC may not operate effec-tively when
Directional control and power may not be achievable while driving on slippery
road surfaces, even if the TRC/VSC sys- tem is operating.
Drive the vehicle carefully in conditions where stability and power may be lost.
■Hill- start assist control does not operate effectively when
●Do not overly rely on hill-start assist control. Hill-start assist control may
not operate effectively on steep inclines and roads covered with ice.
●Unlike the parking brake, hill-start assist control is not intended to hold
the vehicle stationary for an extended period of time. Do not attempt to use hill-start assist control to hold the vehi-
cle on an incline, as doing so may lead to an accident.
■When the TRC/VSC/ABS is acti-vated
The slip indicator light flashes. Always drive carefully. Reckless driving may
cause an accident. Exercise particular care when the indicator light flashes.
■When the TRC/VSC systems are turned off
Be especially careful and drive at a speed appropriate to the road conditions. As
these are the systems to help ensure vehicle stability and dr iving force, do not turn the TRC/VSC systems off unless
necessary.
■Secondary Collision Brake
Do not overly rely on the Secondary Col-
lision Brake. This system is designed to help reduce the possibility of further damage due to a secondary collision,
however, that effect changes according to various conditions. Overly relying on the system may result in death or serious
injury.
■Replacing tires
Make sure that all tires are of the speci-
fied size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recom-
mended tire inflation pressure level.
The ABS, TRC and VSC systems will not
function correctly if different tires are installed on the vehicle.
Contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer for further information when replacing tires or wheels.
■Handling of tires and the suspension
Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause a
system to malfunction.

281
5
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
Interior features
■Adjusting the temperature
Operate the temperature control
switch upwards to increase the tem-
perature and downwards to decrease
the temperature.
■Setting the fan speed
Operate the fan speed control switch
upwards to increase the fan speed and
downwards to decrease the fan speed.
Press the off switch to turn the fan off.
■Changing the air flow mode
 P.283
■Switching between outside air and
recirculated air modes
Operate the outside/recirculated air
mode switch upwards or downwards.
The mode changes as follows each time
the switch is operated.
automatic mode  (outside air
mode)  (recirculated air mode)
 automatic mode
When the system is switched to automatic
mode, the air conditioning system operates
automatically.
■Defogging the windshield
Defoggers are used to defog the wind-
shield and front side windows.
Press the windshield defogger switch.
Set the outside/recirculated air mode
switch to outside air mode if the recircu-
lated air mode is used. (It may switch auto-
matically.)
To defog the windshield and the side win-
dows early, turn the air flow and tempera-
ture up.
To return to the previous mode, press the
windshield defogger switch again when the
windshield is defogged.
■Defogging the rear window and
outside rear view mirrors
Defoggers are used to defog the rear
window, and to remove raindrops, dew
and frost from the outside rear view
mirrors.
Press the rear window and outside rear
view mirror defoggers switch.
The defoggers will automatically turn off
after 15 to 60 minutes. The operation time
changes according to the ambient tem-
perature and vehicle speed.
■Windshield wiper de-icer (if
equipped)
 P.284
■Blower customization
 P.284
■Fogging up of the windows
The windows will easily fog up when the
humidity in the vehicle is high. Turning “A/C” on will dehumidify the air from the outlets and defog the windshield effectively.
●If you turn “A/C” off, the windows may fog up more easily.
●The windows may fog up if the recircu-lated air mode is used.
■Outside/recirculated air mode
●When driving on dusty roads such as tun-nels or in heavy traffic, set the out-
side/recirculated air mode switch to the recirculated air mode. This is effective in preventing outside air from entering the
vehicle interior. During cooling opera- tion, setting the recirculated air mode will also cool the vehicle interior effectively.
●Outside/recirculated air mode may auto-matically switch depending on the tem-

282
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
perature setting or the inside temperature.
■Registering air conditioning settings to electronic keys
●Unlocking the vehicle using an electronic key and turning the engine switch switch> to IGNITION ON mode will recall that key’s registered air conditioning settings.
●When the engine switch is turned off, the current air conditioning
settings will automatically be registered to the electronic key that was used to unlock the vehicle.
●The system may not operate correctly if more than one electronic key is in the
vicinity or if the smart entry & start system is used to unlock the passenger door.
●The doors that can recall the air condi-
tioning setting* when unlocked using the
smart entry & start system can be changed. For details, contact any autho-rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer.*: The doors that can recall the driving posi-
tion memory are changed at the same
time.
■Operation of the air conditioning sys- tem in Eco drive mode
In Eco drive mode, the air conditioning sys- tem is controlled as follows to prioritize fuel
efficiency:
●Engine speed and compressor operation
controlled to restrict heating/cooling capacity
●Fan speed restricted when automatic mode is selected
To improve air conditioning performance, perform the following operations:
●Adjust the fan speed
●Turn off Eco drive mode ( P.242)
■When the outside temperature falls to
nearly 0°C (32°F)
The dehumidification function may not
operate even when “A/C” is selected.
■Ventilation and air conditioning odors
●To let fresh air in, set the air conditioning
system to the outside air mode.
●During use, various odors from inside and
outside the vehicle may enter into and accumulate in the air conditioning sys-tem. This may then cause odor to be
emitted from the vents.
●To reduce potential odors from occur-
ring: • It is recommended that the air condition-ing system be set to outside air mode
prior to turning the vehicle off. • The start timing of the blower may be delayed for a short period of time imme-
diately after the air conditioning system is started in automatic mode.
●When parking, the system automatically switches to fresh air intake mode to encourage better air circulation through-
out the vehicle, helping to reduce odors that occur when starting the vehicle.
■Air conditioning filter
 P.347
■Customization
Settings (e.g. A/C auto switch operation) can be changed.(Customizable features P.423)
WARNING
■To prevent the windshield from fog- ging up
Do not use the windshield defogger switch during cool air operation in extremely humid weather. The difference
between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog
up, blocking your vision.
■When the outside rear view mirror defoggers are operating
Do not touch the outside rear view mir- ror surfaces, as they can become very hot and burn you.

285
5
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
Interior features
mode operation can be customized.
Each time is selected, the fan speed
setting mode changes as follows.
“NORMAL”  “ECO”  “FAST” 
“NORMAL”
■Pollen removal mode
Outside air mode switches to
(recirculated air) mode. Pollen is removed
from the air and the air flows to the upper
part of the body.
Usually the system will automatically turn
off after approximately 1 to 3 minutes.
In order to prevent the windshield from fog-
ging up when the outside air is cold, the
dehumidification function may operate or
the outside/recirculated air mode may not
switch to (recirculated air) mode.
Pollen is filtered even if the pollen removal
mode is turned off.
■nanoe™ system
This vehicle incorporates a biocidal prod-
uct.
Ionised air generated by a device incorpo-
rated in the vehicle purifies the air in the
cabin by suppressing bacteria.
Active substance: Free radicals generated
in situ from ambient air or water
nanoe™ helps to provide purified air by
emitting electrically charged water parti-
cles through the front center vent on the
driver’s side
*.
●When the fan is turned on and nanoe™
on the option control screen is selected,
the nanoe™ system is activated.
●When the fan is operated in the following
conditions, system performance will be
maximized. If the following conditions are
not met, performance will be limited.
• The , or air outlets are being used.
• The front center vent on driver’s side is open.
●When nanoe™ is generated, a small
amount of ozone is emitted and may be
faintly smelled in some situations. How-
ever, this is approximately the same as the
amount that already exists in nature, such
as in forests, and it has no affect on the
human body.
●A slight noise may be heard during oper-
ation. This is not a malfunction.
*: According to temperature and humidity
conditions, fan speed and direction of the
air flow, the nanoe™ system may not
operate at full capacity.
1 Press the automatic mode switch or
select “AUTO” on the sub function
menu. ( P.283)
WARNING
■To prevent burns (vehicles with wind-
shield wiper de-icer)
Do not touch the glass at lower part of
the windshield or to the side of the front
pillars when the windshield wiper de-icer
is on.
■nanoe™ generator
Do not disassemble or repair the genera-
tor because it contains high voltage
parts. Contact any authorized Lexus
retailer or Lexus authorized repairer, or
any reliable repairer if the generator
needs repair.
NOTICE
■To prevent damage to the nanoe™
Do not insert anything into the driver’s
side vent, attach anything to it, or use
sprays around the driver’s side vent.
These things may cause the generator
not to work properly.
Using automatic mode

289
5
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
Interior features
Adjust the seat ventilator fan speed
level
The seat ventilator can be adjusted in 3 lev-
els.
When the seat ventilator is operated, the
fan speed level is displayed on the screen.
Adjust the seat heater temperature
level
The seat heater can be adjusted in 3 levels.
When the seat heater is operated, the tem-
perature level is displayed on the screen.
Adjust the heated steering wheel
temperature level
The heated steering wheel can be adjusted
in 2 levels.
When the heated steering wheel is oper-
ated, the temperature level is displayed on
the screen.
Automatic mode on/off indicators
When the automatic mode is on, the indi-
cator illuminates on the screen.
Sub function menu
When the sub function button on the
Remote Touch is pressed, the following
functions can be set to automatic mode.
: Left-hand side seat heater/seat
ventilator
: Heated steering wheel
: Right-hand side seat heater/seat
ventilator
■Side display
Display the air conditioning control
screen ( P.283)
Adjust the seat heater temperature
level
Each time the switch is selected, the tem-
perature level and level indicator (orange)
change as follows:
AUTO  Hi  Mid  Lo  Off
Adjust the seat ventilator fan speed
level
Each time the switch is selected, the fan
speed level and level indicator (blue)
change as follows:
AUTO  Hi  Mid  Lo  Off
Adjust the heated steering wheel
temperature level
Each time the switch is selected, the tem-
perature level and level indicator change
as follows:
AUTO  Hi  Lo  Off
■The heated steering wheel, seat heaters and seat ventilators can be used when
The engine switch

is in IGNITION ON mode .
■Air conditioning system-linked control mode
When the seat ventilator fan speed level is Hi, the seat ventilator fan speed becomes
A
B
C
D
E
A
B
C
D

292
-$@-$I@0.@0.&@ &&

5-4. Using the interior lights
■Customization
Setting (e.g. the time elapsed before lights
turn off) can be changed. (Customizable features: P.423)
■Turning the door position on
Press the door-linked personal light
switch
The lights are turned on and off according
to whether the doors are opened/closed.
When the door position is on, the indicator
illuminates.
■Turning the lights on/off
Touch the light
When a door is opened while the door
position is on, the lights turn on.
NOTICE
■Removing light lenses
Never remove the lens for the personal lights. Otherwise, the lights will be dam-aged.
■To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the engine is off.
Operating the personal lights
A

304
-$@-$I@0.@0.&@ &&

6-1. Maintenance and care
6-1.Maintenance and care
Working from top to bottom, liber-
ally apply water to the vehicle body,
wheel wells and underside of the
vehicle to remove any dirt and dust.
 Wash the vehicle body using a
sponge or soft cloth, such as a
chamois.
 For hard-to-remove marks, use car
wash soap and rinse thoroughly with
water.
 Wipe away any water.
 Wax the vehicle when the water-
proof coating deteriorates.
If water does not bead on a clean surface,
apply wax when the vehicle body is cool.
■CFRP (Carbon Fiber Reinforced Plas- tic) part (if equipped)
●As the CFRP parts may change color if they are exposed to ultraviolet rays for
extended periods of time, Lexus recom- mends that your vehicle be stored in a place where it will not be exposed to
direct sunlight.
●Do not use wax that contains abrasives.
●Do not use automatic car washes as they may scratch the CFRP parts and damage
the paint.
■Self-restoring coat*
The vehicle body has a self-restoring coat-
ing that is resistant to small surface scratches caused in a car wash etc.
●The coating lasts for 5 to 8 years from when the vehicle is delivered from the plant.
●The restoration time differs depending on the depth of the scratch and outside tem-
perature. The restoration time may become shorter when the coating is warmed by
applying warm water.
●Deep scratches caused by keys, coins,
etc. cannot be restored.
●Do not use wax that contains abrasives.
*: CFRP parts (if equipped) do not have a
self-restoring coat.
■Cleaning the areas with metal accents
Do not use baking soda (sodium bicarbon-
ate) and wax that contains abrasives.
■Automatic car washes (vehicles without CFRP parts)
●Fold the mirrors before washing the vehi-cle. Start washing from the front of the vehicle. Make sure to extend the mirrors
before driving.
●Wash the vehicle with the active rear wing retracted. If the vehicle is washed with the active rear wing raised, depend-
ing on the type of automatic car wash, the brushes of the automatic car wash may become stuck on the active rear wing. In
this case, the active rear wing may not be washed very well or may even be scratched or damaged.
●Brushes used in automatic car washes may scratch the vehicle body and dam-
age the paint.
■High pressure car washes
●Do not allow the nozzles of the car wash
to come within close proximity of the win- dows.
●Before using the car wash, check that the fuel filler door on your vehicle is closed properly.
Cleaning and pr otecting the
vehicle exterior
Perform cleaning in a manner
appropriate to each component
and its material.
Cleaning instructions

330
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
display. (P.92)
The illustration used is intended as an
example, and may differ from the image
that is actually displayed on the multi-infor-
mation display.
■Routine tire inflation pressure checks
The tire pressure warning system does not
replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily
vehicle checks.
■Situations in which the tire pressure warning system may not operate prop-
erly
●In the following cases, the tire pressure
warning system may not operate prop- erly.• If non-genuine Lexus wheels are used.
• A tire has been replaced with a tire that is not an OE (Original Equipment) tire.• A tire has been replaced with a tire that is
not of the specified size. • Tire chains etc. are equipped.• An auxiliary-supported run-flat tire is
equipped. • If a window tint that affects the radio wave signals is installed.
• If there is a lot of snow or ice on the vehi- cle, particularly around the wheels or wheel housings.
• If the tire inflation pressure is extremely higher than the specified level.• If wheels without tire pressure warning
valves and transmitters are used. • If the ID code on the tire pressure warn-ing valves and transmitters is not regis-
tered in the tire pressure warning
computer.
●Performance may be affected in the fol-
lowing situations. • Near a TV tower, electric power plant, gas station, radio station, large display,
airport or other facility that generates strong radio waves or electrical noise• When carrying a portable radio, cellular
phone, cordless phone or other wireless communication device
If tire position information is not correctly
displayed due to the radio wave conditions,
the display may be corrected by driving and
changing the radio wave conditions.
●When the vehicle is parked, the time taken for the warning to start or go off
could be extended.
●When tire inflation pressure declines rap-
idly for example when a tire has burst, the warning may not function.
■Warning performance of the tire pres-sure warning system
The warning of the tire pressure warning system will change in accordance with the
conditions under which it was initialized. For this reason, the system may give a warning
even if the tire pressure does not reach a low enough level, or if the pressure is higher than the pressure that was adjusted to when
the system was initialized.

337
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
pressure warning light does not blink 3 times. (Initialization will not occur while driving)
●After performing init ialization, the tire pressure warning light blinks for 1 minute
then stays on after driving for about 20 minutes.
If the inflation pressure of each tire is still not
displayed, have the vehicle inspected by
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■When registering ID codes
●Initialize the tire pressure warning system after ID code registra tion. Initialization is
disabled if the system was initialized before registration.
●After ID code registration, the tires are hot by driving. Initia lize the tire pressure warning system after the tires become
cold.
The tire pressure warning valve and
transmitter is equipped with a unique
ID code. When replacing a tire pres-
sure warning valve and transmitter, it is
necessary to register the ID code.
When registering the ID codes, per-
form the following procedure.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Press or of the meter con-
trol switches and select .
3 Press or of the meter con-
trol switches and select “Vehicle
Settings”, and then press “OK”.
4 Press or of the meter con-
trol switches and select “TPWS
SET”, and then press “OK”.
5 Press or of the meter con-
trol switches and select “Change
wheel set”, and then press and hold
“OK” until the tire pressure warning
light starts blinking.
The change wheel set mode is activated and registration is started.
A message is displayed on the multi-infor- mation display, and “--” is displayed for inflation pressure of e ach tire. Then, the tire
pressure warning light blinks rapidly for approximately 1 minute and stays on.
6 Drive the vehicle at 40 km/h
(25mph) or more for approxi-
mately 10 to 30 minutes.
When registration is completed, the tire pressure warning light will go off and the inflation pressure of each tire will be dis-
played on the multi-information display.
WARNING
■When initializing the tire pressure
warning system
Do not initialize tire inflation pressure
without first adjusting the tire inflation pressure to the specified level. Other-wise, the tire pressure warning light may
not come on even if the tire inflation pres- sure is low, or it may come on when the tire inflation pressure is actually normal.
Registering ID codes