change time lexus LC500 2018 Service Manual

338
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
The time elapsed before registration is completed differs according to the driving condition and environment.
■Canceling the change wheel set mode
●If turning the engine switch off when in the change wheel set
mode before driving, the change wheel set mode is canceled.
●After driving when in the change wheel set mode, the change wheel set mode cannot be canceled. To cancel the mode,
perform the procedure for ID code regis- tration again and turn the engine switch off before driving.
●If the change wheel set mode is canceled, the ID codes that have already been reg-
istered are communicated. When com- munication is finished, the tire pressure warning light will turn off.
■When ID code registration may not
operate properly
●Do not move the vehicle backward
during registration. Registration is started again from the beginning and it may take longer than usual.
●When another vehicle is running the side of the vehicle such as in heavy traffic, it
may take longer to detect the vehicle’s tire pressure warning valves and trans-mitters.
●If tire pressure warning valves and trans-mitters are in the vehicle, the ID codes
may not be registered.
If registration takes long time, perform the
procedure for ID code registration again
after parking the vehicle for 20 minutes.
If the ID codes cannot be registered even
when performing the above procedure,
contact any authorized Lexus retailer or
Lexus authorized repairer, or any reliable
repairer.

381
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
Power was turned off due to the automatic power off function. Next time when starting the hybrid system, operate the hybrid system for approximately 5 minutes to recharge the 12-volt battery.
■If a message that indicates the need for the shift lever operation is shown
To prevent the shift lever from being operated incorrectly or the vehicle from moving unex- pectedly, a message that requires shifting the shift lever may be shown on the multi-informa-
tion display. In that case, follow the instru ction of the message and shift the shift lever.
■If “Front Camera Unavailable” or “Front Camera Vision Blocked Clean and Demist Windshield” is shown
The following systems may be suspended un til the problem shown in the message is resolved.
●PCS
●LKA
●Dynamic radar cruise cont rol with full-speed range
●Automatic High Beam
■If “Engine Stopped Steering Power Low” (LC500) or “Hybrid System Stopped Steer- ing Power Low” (LC500h) is shown
The steering wheel may become extremely heavy. If the steering wheel becomes heavier than usual when operating, hold firmly and operate using more force than usual.
■If “Warming Up Maximum Vehicle Speed: 110km/h” is shown (LC500h)
The transmission is being warmed up and the ve hicle is unable to be driven over 110 km/h (65 mph). Wait until the transmission warms up.
■If “Stop the vehicle in a safe place Shift to P position” is shown (LC500h)
There may be a malfunction in the hybrid system or the shift position may be shifted to N for a long time. Immediately stop the vehicle and contact any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■If “Oil Maintenance Required Soon” is shown (LC500h)
The engine oil is scheduled to be changed. Check the engine oil, and change if necessary.
After changing the engine oil, the message should be reset. ( P.321)
■If “Engine Oil Level Low Add or Replace” is shown
The engine oil level is low. Check the level of engine oil, and add if necessary. This message
may appear if the vehicle is stopped on a slope. Move the vehicle to a level surface and check to see if the message disappears.
■If a message that indicates the need for referring to Owner’s Manual is shown
●If any of the following messages is shown on the multi-information display, follow the instructions.• “Engine Coolant Temp High” ( P.403, 403)
•“Battery low” ( P.392) • “Transmission Fluid Temp High” ( P.174, 180)
●If any of the following messages is shown on the multi-information display, it may indicate a malfunction. Have the vehicle inspected by any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer immediately.
• “Entry & Start System Malfunction”

391
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
ACCESSORY mode.
3Firmly depress the brake pedal and
check that is shown on the
multi-information display.
4 Press the engine switch switch>.
In the event that the engine tem> still cannot be started, contact
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
■Stopping the engine
Set the parking brake, shift the shift position to P and press the engine switch as you normally do when stopping
the engine .
■Electronic key battery
As the above procedure is a temporary
measure, it is recommended that the elec- tronic key battery be replaced immediately when the battery is depleted. ( P.349)
■Alarm (if equipped)
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set, the alarm may be triggered.
■Changing engine switch
modes
Release the brake pedal and press the
engine switch in step 3
above. The engine does not start and modes will be changed each time the
switch is pressed. ( P.165, 170)

398
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
ponents when the vehicle is running at a low speed for an extended period, such as in heavy traffic.
■When the 12-volt battery is removed or
discharged
●Information stored in the ECU is cleared.
When the 12-volt battery is depleted, have the vehicle inspected at any autho-rized Lexus retailer or Lexus authorized
repairer.
●Some systems may require initialization.
( P.436)
■When removing the 12-volt battery ter- minals
When the 12-volt battery terminals are removed, the information stored in the ECU is cleared. Before removing the 12-
volt battery terminals, contact any autho- rized Lexus retailer or Lexus authorized repairer.
■Charging the 12-volt battery
The electricity stored in the 12-volt battery will discharge gradually even when the
vehicle is not in use, due to natural dis- charge and the draining effects of certain
electrical appliances. If the vehicle is left for a long time, the 12-volt battery may dis-charge, and the engine
may be unable to start. (The 12-volt battery recharges automatically during driving.)
■When recharging or replacing the 12-volt battery
●In some cases, it may not be possible to unlock the doors using the smart entry &
start system when the 12-volt battery is discharged. Use the wireless remote control or the mechanical key to lock or
unlock the doors.
●The engine may not start
on the first attempt after the 12-volt bat- tery has recharged but will start normally after the second attempt. This is not a
malfunction.
●The engine switch mode
is memorized by the vehicle. When the 12-volt battery is reconnected, the system will return to the mode it was in before
the 12-volt battery was discharged.
Before disconnecting the 12-volt battery, turn the engine switch off. If you are unsure what mode the engine
switch was in before the 12-volt battery discharged, be especially careful when reconnecting the 12-volt
battery.
●If the 12-volt battery discharges, it may
not be possible to shift the shift position to other positions. In this case, the vehicle cannot be towed without lifting both rear
wheels because the rear wheels will be locked. ( P.363)
■When replacing the 12-volt battery
●Use a Central Degassing type 12-volt battery (European Regulations).
●LC500: Use a 12-volt battery that the case size is same as the previous one (LN4), 20 hour rate capacity (20HR) is
equivalent (80Ah) or greater, and per- formance rating (CCA) is equivalent (685A) or greater.
LC500h: Use a 12-volt battery that the case size is same as the previous one (LN3), 20 hour rate capacity (20HR) is
equivalent (70Ah) or greater, and perfor- mance rating (CCA) is equivalent
(600A) or greater. • If the sizes differ, the 12-volt battery can-not be properly secured.
• If the 20 hour rate capacity is low, even if the time period where the vehicle is not used is a short time, the 12-volt battery
may discharge and engine may not be able to start.
●Use a 12-volt battery with a handle. If a 12-volt battery without a handle is used, removal is more difficult.
●After exchanging, firmly attach the fol-lowing items to the exhaust hole of the 12-
volt battery. • Use the exhaust hose that was attached to the 12-volt battery before exchanging.
• Use the exhaust hole plug included with the 12-volt battery exchanged or the one installed on the battery prior to the
exchange. (Depending on the 12-volt battery to be exchanged, the exhaust hole may be plugged.)

431
8
-$@-$I@0.@0.&@ &&

8-2. Customization
Vehicle specifications
■Outside rear view mirrors (P.147)
■Power windows (P.150)
■Turn signal lever (P.186)
■Automatic light control system (P.191)
FunctionDefault settingCustomized setting
Automatic mirror folding and
extending operation
Linked to the
locking/unlock-
ing of the doors
Off
——OLinked to operation
of the engine switch

Linked mirror function when
reversingOnOff——O
FunctionDefault settingCustomized setting
Mechanical key linked operationOffOn——O
Wireless remote control linked
operationOffOn——O
Wireless remote control linked
operation signal (buzzer)OnOff——O
FunctionDefault settingCustomized setting
The number of times the turn signal
lights flash automatically when the
turn signal lever is moved to the
first position during a lane change
3
5
——O7
Off
FunctionDefault settingCustomized setting
Light sensor sensitivityStandard-2 to 2O—O
Follow me home
(Time elapsed before headlights
automatically turn off)
30 seconds
60 seconds
——O90 seconds
120 seconds
ABC
ABC
ABC
ABC

435
8
-$@-$I@0.@0.&@ &&

8-2. Customization
Vehicle specifications
■Vehicle customization
●When the speed-detecting automatic door lock and shift-linked automatic door
lock are both on, the door lock operates as follows.• When shifting the shift position to any
position other than P, both side the doors will be locked.• If the vehicle is started with both side
doors locked, the speed-detecting auto- matic door lock will not operate.
• If the vehicle is started with any door unlocked, the speed-detecting auto-matic door lock will operate.
●When the smart entry & start system is off, the entry unlock function cannot be
customized.
●When the doors remain closed after
unlocking the doors and the timer acti- vated automatic door lock function acti-vates, signals will be generated in
accordance with the operational signal (Emergency flashers) function setting.
●Some settings can be changed using a switch or the audio system screen. If a setting is changed using a switch, the
changed setting will not be reflected on the audio system screen until the engine switch is turned off and
then to IGNITION ON mode .
Chassis control in custom modeNormalSportO——Comfort
Air conditioning operation in cus-
tom modeNormalEcoO——
FunctionDefault settingCustomized settingABC