change time lexus LC500 2018 User Guide

164
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
■Electronic key battery depletion
 P.112
■Conditions affecting operation
 P.124
■Notes for the entry function
 P.124
■Steering lock function
●After turning the engine switch off and
opening and closing the doors, the steer- ing wheel will be locked due to the steer-ing lock function. Op erating the engine
switch again automatically cancels the steering lock.
●When the steering lock cannot be released, “Push engine switch while turn-ing the steering wheel in either direction”
will be displayed on the multi-information display. Press the engine switch shortly and firmly
while turning the steering wheel left and right.
●To prevent the steering lock motor from overheating, operation of the motor may
be suspended if the engine is turned on and off repeatedly in a short period of time. In this case, refrain from operating
the engine switch. After about 10 sec- onds, the steering lock motor will resume functioning.
■If there is a malfunction in the smart
entry & start system
If “Entry & Start System Malfunction” is dis-
played on the multi-information display, the system may be malfunctioning. Have the vehicle inspected by any authorized Lexus
retailer or Lexus authorized repairer, or any reliable repairer immediately.
■Electronic key battery
 P.349
■Operation of the engine switch
●If the switch is not pressed shortly and firmly, the engine switch mode may not
change or the engine may not start.
●If attempting to restart the engine imme-
diately after turning the engine switch off, the engine may not start in some cases. After turning the engine switch off, please
wait a few seconds before restarting the engine.
■Customization
If the smart entry & start system has been deactivated in a customized setting, refer to P.389.
WARNING
■When starting the engine
Always start the engine while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the
engine under any circumstances. Doing so may cause an accident result-ing in death or serious injury.
■Caution while driving
If engine failure occurs while the vehicle is moving, do not lock or open the doors
until the vehicle reaches a safe and com- plete stop. Activation of the steering lock in this circumstance may lead to an acci-
dent, resulting in death or serious injury.
NOTICE
■When starting the engine
●Do not race a cold engine.
●If the engine becomes difficult to start
or stalls frequently, have your vehicle checked by any authorized Lexus retailer or Lexus authorized repairer,
or any reliable repairer immediately.

165
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
1Stop the vehicle completely.
2 If the parking brake is in manual
mode, set the parking brake.
( P.187)
3 Shift the shift position to P.
( P.175)
Check that the shift position indicator
shows P. ( P.175)
4Press the engine switch.
The engine will stop, and the meter display will be extinguished (the shift position indi-
cator will be extinguished a few seconds after the meter display).
5 Check that “ACCESSORY” or
“IGNITION ON” is not shown on
the meter.
■Automatic P position selection function
 P.176
Modes can be changed by pressing
the engine switch with the brake pedal
released. (The mode changes each
time the switch is pressed.)
NOTICE
■Symptoms indicating a malfunction with the engine switch
If the engine switch seems to be operat- ing somewhat differently than usual, such as the switch sticking slightly, there may
be a malfunction. Contact any autho- rized Lexus retailer or Lexus authorized repairer, or any reliable repairer immedi-
ately.
Stopping the engine
WARNING
■Stopping the engine in an emergency
●If you want to stop the engine in an
emergency while driving the vehicle, press and hold the engine switch for more than 2 seconds, or press it briefly
3 times or more in succession. ( P.360) However, do not touch the engine
switch while driving except in an emer- gency. Turning the engine off while driving will not cause loss of steering
or braking control, however, power assist to the steering will be lost. This will make it more difficult to steer
smoothly, so you should pull over and stop the vehicle as soon as it is safe to do so.
●If the engine switch is operated while the vehicle is running, a warning mes-
sage is shown on the multi-information display and a buzzer sounds.
●When restarting the engine after an emergency shutdown, press the engine switch.
Changing engine switch modes

166
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
1Off
The emergency flashers can be used.
2ACCESSORY mode
Some electrical components such as the
audio system can be used.
“ACCESSORY” will be displayed on the
meter.
3 IGNITION ON mode
All electrical components can be used.
“IGNITION ON” will be displayed on the
meter.
■Auto power off function
If the vehicle is left in ACCESSORY mode for more than 20 minutes or IGNITION
ON mode (the engine is not running) for more than an hour with the shift position in P, the engine switch will automatically turn
off. However, this function cannot entirely prevent the 12-volt battery discharge. Do not leave the vehicle with the engine switch
in ACCESSORY or IGNITION ON mode for long periods of time when the engine is not running.
■When the shift control system malfunc-tions
When attempting to turn the engine switch off while there is a malfunction in the shift control system, the engine switch mode
may change to ACCESSORY mode. In this case, ACCESSORY mode may be turned off by applying the parking brake and press-
ing the engine switch again. If there is a mal- function in the system, have the vehicle inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer immediately.
NOTICE
■To prevent 12-volt battery discharge
●Do not leave the engine switch in
ACCESSORY or IGNITION ON mode for long periods of time without the engine running.
●If “ACCESSORY” or “IGNITION
ON” is displayed on the meter, the engine switch is not off. Exit the vehicle after turning the engine switch off.

168
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
on the multi-information display, read the message and follow the instructions.
■When the ambient temperature is low, such as during winter driving conditions
●When starting the hybrid system, the flashing time of the “READY” indicator
may be long. Leave the vehicle as it is until the “READY” indicator is steady on, as steady means the vehicle is able to move.
●When the hybrid battery (traction bat-tery) is extremely cold (below approxi-
mately -30°C [-22°F]) under the influence of the outside temperature, it may not be possible to start the hybrid
system. In this case, try to start the hybrid system again after the temperature of the hybrid battery increases due to the out-
side temperature increase etc.
■Sounds and vibrations specific to a hybrid vehicle
 P.64
■If the 12-volt battery is discharged
The hybrid system cannot be started using
the smart entry & start system. Refer to P.393 to restart the hybrid system.
■Electronic key battery depletion
 P.112
■Conditions affecting operation
 P.124
■Note for the entry function
 P.124
■Steering lock function
●After turning the power switch off and opening and closing the doors, the steer-
ing wheel will be locked due to the steer- ing lock function. Operating the power switch again automatically cancels the
steering lock.
●When the steering lock cannot be
released, “Push power switch while turn- ing the steering wheel in either direction” will be displayed on the multi-information
display. Press the power switch shortly and firmly while turning the steering wheel left and
right.
●To prevent the steering lock motor from
overheating, the motor may be sus- pended if the hybrid system is turned on and off repeatedly in a short period of
time. In this case, refrain from operating the power switch. After about 10 sec-onds, the steering lock motor will resume
functioning.
■If there is a malfunction in the smart entry & start system
If “Entry & Start System Malfunction” is dis- played on the multi-information display, the system may be malfunctioning. Have the
vehicle inspected by any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer immediately.
■If the “READY” indicator does not come
on
In the event that the “READY” indicator does not come on even after performing the proper procedures for starting the vehi-
cle, contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer immediately.
■If the hybrid system is malfunctioning
 P.68
■Electronic key battery
 P.349
■Operation of the power switch
●If the switch is not pressed shortly and
firmly, the power switch mode may not change or the hybrid system may not start.
●If attempting to restart the hybrid system immediately after turning the power
switch off, the hybrid system may not start in some cases. After turning the power

170
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Modes can be changed by pressing
the power switch with the brake pedal
released. (The mode changes each
time the switch is pressed.)
1 Off
The emergency flashers can be used.
2ACCESSORY mode
Some electrical components such as the
audio system can be used.
“ACCESSORY” will be displayed on the
meter.
3 ON mode
All electrical components can be used.
“IGNITION ON” will be displayed on the
meter.
■Auto power off function
If the vehicle is left in ACCESSORY mode
for more than 20 minutes or ON mode (the hybrid system is not operating) for more than an hour with the shift position in P, the
power switch will automatically turn off. However, this function cannot entirely pre-vent the 12-volt battery discharge. Do not
leave the vehicle with the power switch in ACCESSORY or ON mode for long peri-ods of time when the hybrid system is not
operating.
■When the shift control system malfunc- tions
When attempting to turn the power switch off while there is a malfunction in the shift control system, the power switch mode may
change to ACCESSORY mode. In this case, ACCESSORY mode may be turned off by applying the parking brake and press-
ing the power switch again. If there is a mal- function in the system, have the vehicle inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer immediately.
WARNING
●When restarting the hybrid system after an emergency shutdown, press the power switch.
Changing power switch modes
NOTICE
■To prevent 12-volt battery discharge
●Do not leave the power switch in ACCESSORY or ON mode for long
periods of time without the hybrid sys- tem on.
●If “ACCESSORY” or “IGNITION
ON” is displayed on the meter, the power switch is not off. Exit the vehicle after turning the power switch off.

178
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
■Automatic deactivation of shift range selection in the D position
Shift range selection in the D position will be deactivated in the following situations:
●When the vehicle comes to a stop
●If the accelerator pedal is depressed for
more than a certain period of time
●When the shift lever is moved to D again
●When pressing and holding the “+” pad- dle shift switch
■Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some- times be restricted. In some circumstances, downshifting may not be possible even
when the paddle shift switch is operated. (A buzzer will sound twice.)
To enter M mode, shift the shift position
to M. Gears can be selected by oper-
ating the paddle shift switches, allowing
you to drive in the gear of your choos-
ing.
1 Upshifting
2 Downshifting
The gear changes once every time the
paddle shift switch is operated.
The selected gear, from M1 to M10, will be
fixed and displayed in the meter.
When in the M position, the gear will
not change unless the paddle shift
switches are operated.
However, even when in the M position,
the gears will be automatically
changed in the following situation:
 When vehicle speed drops (down-
shift only).
 When it is necessary to protect the
engine or automatic transmission
when the engine coolant tempera-
ture is low, the automatic transmis-
sion fluid temperature is high or low,
or other reasons.
Also, the gear will not shift when the
vehicle speed is low, even if an upshift
operation is performed.
■Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some- times be restricted. In some circumstances, downshifting may not be possible even
when the paddle shift sw itch is operated. (A buzzer will sound twice.)
The Gear Shift Indicator display is a
guide to help the driver achieve
improved fuel economy and reduced
exhaust emissions within limits of
engine performance.
Selecting gears in the M position
Gear Shift Indicator (if
equipped)

181
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
sages on the multi-information display.
■After recharging/reconnecting the 12- volt battery
 P.325
■Customization
Settings (e.g. Reverse warning buzzer) can
be changed. (Customizable features: P.423)
Shift lever
Operate the shift lever gently and securely
in the direction of the arrow on the shift
position indicator.
To shift to N, slide the shift lever in the
direction of the arrow and hold it.
Release the shift lever after each shifting
operation to allow it to return to its regular
position ( ).
Shifting to M is only possible when the shift
position is in D.
When shifting from P to N, D or R, from N,
D or R to P, from D to R, or from R to D,
ensure that the brake pedal is being
depressed and the vehicle is stationary.
Shift position indicator
Meter display:
The current shift position is highlighted.
When any shift position other than D or M
is selected, the arrow toward M and M
WARNING
■When driving on slippery road sur- faces
Do not accelerate or shift the shift posi- tion suddenly. Sudden changes in engine braking may
cause the vehicle to spin or skid, resulting in an accident.
NOTICE
■Hybrid battery (traction battery) charge
If the shift position is in N, the hybrid bat- tery (traction battery) will not be
charged. To help prevent the battery from discharging, avoid leaving the N position selected for an extended period
of time.
■Situations where shift control system malfunctions are possible
If any of the following situations occur, shift control system malfunctions are possible. Immediately stop the vehicle in
a safe place on level ground, apply the parking brake, and then contact any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
●When the warning message indicating the shift control system appears on the
multi-information display.
●The display indicates that no shift posi- tion is selected for more than a few seconds.
Shifting the shift lever
A
B

184
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
tions. When the “+” paddle shift switch
is operated, the shift range switches to
a range that is one range higher than
the current range.
Changing the shift range allows
restriction of the highest shift range,
preventing unnecessary upshifting and
enabling the level of engine braking
force to be selected.
1 Upshifting
2 Downshifting
The selected shift range, from D1 to D10,
will be displayed in the meter.
To return to normal D position driving, the
“+” paddle shift switch must be held down
for a period of time.
A lower shift range will provide greater
engine braking forces than a higher shift
range.
■Automatic deactivation of shift range selection in the D position
Shift range selection in the D position will be deactivated in the following situations:
●When the vehicle comes to a stop
●If the accelerator pedal is depressed for
more than a certain period of time
●When the shift lever is moved to D again
●When the “+” paddle shift switch is pressed and held
●When dynamic radar cruise control with full-speed range or cruise control is oper-
ating
■Downshifting restriction warning buzzer
To help ensure safety and driving perfor- mance, downshifting operation may some-times be restricted. In some circumstances,
downshifting may not be possible even when the paddle shift sw itch is operated. (A buzzer will sound twice.)
To enter M mode, shift the shift position
to M. Gears can be selected by oper-
ating the paddle shift switches, allowing
you to drive in the gear of your choos-
ing.
1 Upshifting
2 Downshifting
The gear changes once every time the
paddle shift switch is operated.
Meter dis-
playFunction
D2 - D10
A gear in the range between
D1 and the selected shift
range is automatically cho-
sen depending on vehicle
speed and driving conditions
D1Setting the shift range at D1
Selecting gears in the M position

185
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
The selected gear, from M1 to M10, will be
fixed and displayed in the meter.
When in the M position, the gear will
not change unless the paddle shift
switches are operated.
However, even when in the M position,
the gears will be automatically
changed in the following situation:
 When vehicle speed drops (down-
shift only).
 When vehicle speed increases
(upshift only).
 When the accelerator pedal is firmly
depressed.
 When it is necessary to protect the
transmission when the transmission
fluid temperature is high or low, or
other reasons.
Also, the gear will not shift when the
vehicle speed is low, even if an upshift
operation is performed.
■Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some- times be restricted. In some circumstances, downshifting may not be possible even
when the paddle shift switch is operated. (A buzzer will sound twice.)
The Gear Shift Indicator display is a
guide to help the driver achieve
improved fuel economy and reduced
exhaust emissions within limits of
engine performance.
When not in operation
Shift-up indicator
■Gear Shift Indicator function
 This function automatically operates
during M mode.
 By following the Shift-up indicator
and shifting up accordingly, it is pos-
sible to achieve improved fuel econ-
omy and reduced exhaust
emissions.
 The Gear Shift Indicator does not
have a similar function for down-
shifting.
 Depending on the driving condi-
tions, the Gear Shift Indicator may
not display the Shift-up indicator
while driving in M mode.
Gear Shift Indicator
WARNING
■Gear Shift Indicator display
For safety, the driver should not look only at the display. Refer to the display when it
is safe to do so while considering actual traffic and road conditions. Failure to do so may lead to an accident.
A
B

186
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
1Right turn
2 Lane change to the right (move the
lever partway and release it)
The right hand signals will flash 3 times.
3 Lane change to the left (move the
lever partway and release it)
The left hand signals will flash 3 times.
4 Left turn
If the turn signals do not stop flashing
after turning left or right, or if you want
to stop them flashing, operate the lever
in the opposite direction to either posi-
tion 2 or 3. If you move the lever to
either position 1 or 4, the selected turn
signals will flash.
■Turn signals can be operated when
The engine switch

is in
IGNITION ON mode .
■If the indicator flashes faster than usual
Check that a light bulb in the front or rear
turn signal lights has not burned out.
■If the turn signals stop flashing before a lane change has been performed
Operate the lever again.
■Customization
 P.423
Turn signal lever
Operating instructions