torque LEXUS LS430 2003 Factory Owner's Manual

Fig. 38: Putting Matchmarks On Transmission Case And Torque Converter Clutch Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
37.INSPECT TORQUE CONVERTER CLUTCH ASSY (SEE INSPECTION
)
SST 09350-32014 (09351-32010, 09351-32020)
38.INSTALL TORQUE CONVERTER CLUTCH ASSY
a. Using calipers and a straight edge, measure dimension A between the transmission and the end
surface of the drive plate.

Fig. 39: Measuring Dimension A Between Transmission And End Surface Of Drive Plate
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Aligning the matchmarks on the transmission case and torque converter clutch assy, engage the
splines of the input shaft and turbine runner.

Fig. 40: Aligning Matchmarks On Transmission Case And Torque Converter Clutch Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Engage the splines of the stator shaft and stator while turning the torque converter clutch assy.
HINT:
Turn the torque converter clutch assy approximately 180°.

<0029004c004a0011000300170014001d000300280051004a0044004a004c0051004a000300360053004f004c005100480056000300320049000300360057004400570052005500030036004b00440049005700030024005100470003003600570044005700
520055[
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d. Turn the torque converter clutch assy and align the matchmarks on the torque converter clutch assy
and transmission case to engage the key of the oil pump drive gear into the slot on the torque
converter clutch assy.

Fig. 42: Aligning Matchmarks On Torque Converter Clutch Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e. Using calipers and a straight edge, measure the dimension B shown in the illustration and check
that B is
greater than A measured in step (a).

Fig. 43: Measuring Dimension B
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
39.INSTALL TRANSMISSION CONTROL SHAFT LEVER RH
a. Install the transmission control shaft lever RH with the nut.
Torque: 16 N.m (160 kgf.cm, 12 ft.lbf)

Fig. 44: Installing Transmission Control Shaft Lever RH With Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
40.INSTALL ENGINE MOUNTING INSULATOR REAR NO.1
a. Install the engine mounting insulator rear No.1 with the 4 bolts.
Torque: 12 N.m (122 kgf.cm, 9 ft.lbf)

Fig. 45: Installing Engine Mounting Insulator Rear No.1 With 4 Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
41.INSTALL AUTOMATIC TRANSMISSION ASSY
a. Install the automatic transmission assy to the engine with the 9 bolts.
Torque:
Bolt A: 14 mm head bolt: 37 N.m (380 kgf.cm, 27 ft.lbf)
Bolt B: 17 mm head bolt: 71 N.m (724 kgf.cm, 52 ft.lbf)
HINT:
Bolt (a) is tightened to the wire harness clamp.

Fig. 46: Installing Automatic Transmission Assy To Engine With 9 Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Install the 6 torque converter clutch mounting bolts.
Torque: 48 N.m (490 kgf.cm, 35 ft.lbf)
HINT:
First install the black colored bolt and then the remainin
g 5 bolts.

Fig. 47: Installing 6 Torque Converter Clutch Mounting Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
42.INSTALL FLYWHEEL HOUSING UNDER COVER
a. Install the fly wheel housing under cover with the 2 bolts.
Torque: 18 N.m (184 kgf.cm, 13 ft.lbf)