instrument panel LEXUS LS430 2003 Factory Manual PDF

Fig. 2: Identifying Instrument Panel/Meter Components (2 Of 4)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 3: Identifying Instrument Panel/Meter Components (3 Of 4)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 4: Identifying Instrument Panel/Meter Components (4 Of 4)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

PRECAUTION
1. HANDLING PRECAUTIONS FOR STEERING SYSTEM
a. Care must be taken when replacing parts. Incorrect replacement could affect the performance of the
steering system and result in a driving hazard.
2. HANDLING PRECAUTIONS FOR SRS AIRBAG SYSTEM
a. The LS430 is equipped with SRS (Supplemental Restraint System) such as the driver airbag and
front passenger airbag, etc. Failure to carry out service operations in the correct sequence could
cause the SRS to unexpectedly deploy during servicing, possibly leading to a serious accident.
Before servicing (including removal or installation of parts, inspection or replacement), be sure to
read the precautionary notice for the supplemental restraint system (see PRECAUTION
).
REPLACEMENT
HINT:
COMPONENTS: SEE COMPONENTS
Installation is in the reverse order of removal.
A bolt without a torque specification is shown in the standard bolt chart (see STANDARD BOLT ).
1. TABLE OF BOLT, SCREW AND NUT
HINT:
The bolts, screws and nuts, necessary for installation and removal of the instrument panel, are shown in
the illustration below with alphabet code.

HINT:
Disconnect the battery negative terminal with the steering column assy extended.
Be sure to extend the steering column, otherwise the steering column cover cannot be removed.
5.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
6.REMOVE SWITCH & VOLUME CASE (SEE OVERHAUL
)
7.REMOVE STEERING WHEEL COVER LOWER NO.2 (SEE OVERHAUL
)
8.REMOVE HORN BUTTON ASSY (SEE OVERHAUL
)
9.REMOVE STEERING WHEEL ASSY (SEE OVERHAUL
)
<00360036003700030013001c001c001800130010001800130013001400160003000b0013001c001c00180014001000130018001300140013000f00030013001c001c00180015001000130018001300140013000f00030013001c001c001800160010001300
18001300150013000f00030013001c001c0018001700100013[5021)
10.REMOVE STEERING COLUMN COVER (SEE OVERHAUL
)
11.REMOVE SPIRAL CABLE SUB-ASSY (SEE REPLACEMENT
)
12.REMOVE TURN SIGNAL SWITCH ASSY (SEE REPLACEMENT
)
13.REMOVE INSTRUMENT PANEL SAFETY PAD GARNISH SUB-ASSY
a. Using a screwdriver, disengage the upper/lower 2 claws inside the instrument panel safety pad
garnish sub-assy.
HINT:
Tape up the screwdriver tip before use.

Fig. 6: Removing Instrument Panel Safety Pad Garnish Sub-Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
14.REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER LOWER
a. Using a screwdriver, disengage the 2 claws and remove the instrument cluster finish panel center
lower.
HINT:
Tape up the screwdriver tip before use.

b. Disconnect the connector.
Fig. 7: Removing Instrument Cluster Finish Panel Center Lower

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
15.REMOVE INSTRUMENT CLUSTER FINISH PANEL END
a. Using a screwdriver, disengage the 2 claws and the clip and remove the instrument cluster finish
panel center end.
HINT:
Tape up the screwdriver tip before use.
b. Disconnect the connector.
16.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.1
a. Remove the 2 screws < N >.
b. Disengage the 2 clips and remove the instrument panel under cover sub-assy No.1.
c. Disconnect the connectors.

Fig. 8: Removing Instrument Panel Under Cover Sub-Assy No. 1
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
17.REMOVE COIN BOX ASSY
a. Pull the parking brake and remove the 2 nuts from the coin box assy.
b. Using a moulding remover, disengage the 2 claws and remove the coin box assy.
HINt:
Use a screwdriver if a moulding remover is not available.
tape up the screwdriver tip before use.
c. Disconnect the connectors.

Fig. 10: Removing Outer Mirror Switch Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
19.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSY NO.1
a. Remove the 2 bolts and the screw < N >.
b. Remove the 2 bolts < D > and the hood lock control cable assy.
c. Disengage the 4 clips and remove the instrument panel safety pad sub-assy No.1.
d. Disconnect the connectors.

Fig. 11: Removing Instrument Panel Safety Pad Sub-Assy No.1
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
20.REMOVE INSTRUMENT PANEL AIR BAG ASSY LOWER NO.1 (SEE REPLACEMENT
)
21.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.2
a. Disengage the 4 clips and the 2 claws and remove the instrument panel under cover sub-assy No.2.
b. Disconnect the connector.