LEXUS NX200T 2016 Owners Manual

5317-3. Do-it-yourself maintenance
7
Maintenance and care
NX200t_OM_USA_OM78081U
Remove the light bulb.
Replace the light bulb.
Turn clockwise and set the bulb
base.
Attach the clip to the cover.Push up on the center of the
clip.
Attach the clip.4
5
6
7
1
2

5327-3. Do-it-yourself maintenance
NX200t_OM_USA_OM78081U
Attach the cover. Align the 2 tabs positions and
close the cover.
Fix the cover by pushing the
center of the clip.
Install the engine compartment cover. ( P. 4 9 1 )
■Rear turn signal lights
Open the back door and attach
protective tape around the lamp
body. (Use masking tape, do not
use Duct tape, as duct tape may
leave markings.)
Remove the cover.
It is recommended for safeguarding
to wrap the tip of the screwdriver
with a cloth, etc., in order to prevent
scratches to the vehicle.
Remove the 2 bolts.
8
1
2
9
1
2
3

5337-3. Do-it-yourself maintenance
7
Maintenance and care
NX200t_OM_USA_OM78081U
Remove the light unit.Attach 2 long pieces of the
masking tape and fold the
excess portion over in half.
Hold the section folded in half,
pull toward the rear of the lens
and remove.
Turn the bulb base counterclock-
wise.
Remove the light bulb.4
1
2
5
6

5347-3. Do-it-yourself maintenance
NX200t_OM_USA_OM78081U
Replace the light bulb.
Turn clockwise and set the bulb
base.
Confirm that cable is fixed to the tab.
Set the light unit. Align the light unit with the 2
tabs on the rear bumper.
Push the light unit forward
while pushing A.
Confirm that the grommet fits into
the bolt installation hole on the
light unit.
37
Ta b
38
Grommet
A
Ta b
Ta b
9
1
2

5357-3. Do-it-yourself maintenance
7
Maintenance and care
NX200t_OM_USA_OM78081U
Install the 2 bolts.
Install the cover.
■Back-up lightsOpen the back door and remove
the cover.
Press down on the notch on the
cover and remove the cover.
It is recommended for safeguarding
to wrap the tip of the screwdriver
with a cloth, etc., in order to prevent
scratches to the vehicle.
Turn the bulb base counterclock-
wise.
10
11
1
2

5367-3. Do-it-yourself maintenance
NX200t_OM_USA_OM78081U
Remove the light bulb.
Replace the light bulb, and install
the bulb base.
Install the back door cover
Align the 2 tabs on the cover and
install.
3
4
5

5377-3. Do-it-yourself maintenance
7
Maintenance and care
NX200t_OM_USA_OM78081U
■Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by your Lexus
dealer.
●Headlight low beams
●Headlight high beams (LED type)
●Front turn signal lights (LED type)
●Parking lights and Daytime running lights
●Front fog lights
●Cornering lights (if equipped)
●Front side marker lights (LED type)
●Side turn signal lights
●Stop/tail lights
●Rear side marker lights
●High mounted stoplight
●License plate lights
●Outer foot lights
■After replacing the bulbs
■LED lights
The headlight low beams, headlight high beams (LED Type), front turn signal lights (LED
Type), parking lights, daytime running lights, front fog lights, cornering lights (if
equipped), front side marker lights (LED Type), side turn signal lights, rear side marker
lights, stop/tail lights, rear side marker lights, high mounted stoplight and license plate
lights, outer foot lights consist of a number of LEDs. If any of the LEDs burn out, take your
vehicle to your Lexus dealer to have the light replaced.
■Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not indicate a
malfunction. Contact your Lexus dealer for mo re information in the following situations:
●Large drops of water have built up on the inside of the lens.
●Wa t e r h a s b u i l t u p i nside the headlight.
■When replacing light bulbs
P. 5 2 2
After removing the engine compartment cover,
return the cover to original position with the
clips.
Insert
Press
1
2

5387-3. Do-it-yourself maintenance
NX200t_OM_USA_OM78081U
WA R N I N G
■Replacing light bulbs
●Be sure to stop the engine and turn off the lights. Do not attempt to replace the bulb
immediately after turning off the lights.
The bulbs become very hot and may cause burns.
●Do not touch the glass portion of the light bulb with bare hands. When it is unavoid-
able to hold the glass portion, use and ho ld with a clean dry cloth to avoid getting
moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
●Fully install light bulbs and any parts used to secure them. Failure to do so may result
in heat damage, fire, or water entering the headlight unit. This may damage the head-
lights or cause condensation to build up on the lens.
●Do not attempt to repair or disassemble light bulbs, connectors, electric circuits or
component parts.
Doing so may result in death or se rious injury due to electric shock.
■To prevent damage or fire
●Make sure bulbs are fully seated and locked.
●Check the wattage of the bulb before installin g to prevent heat damage.

539
8When trouble arises
NX200t_OM_USA_OM78081U
8-1. Essential informationEmergency flashers ..................540
If your vehicle has to be stopped in an
emergency.................................. 541
8-2. Steps to take in an emergency If your vehicle needs to be towed ..................................... 542
If you think something is wrong ...........................................548
Fuel pump shut off system ...... 549
If a warning light turns on or a warning buzzer
sounds..........................................550
If a warning message is displayed..................................... 557
If you have a flat tire...................560
If the engine will not start ........ 573
If the shift lever cannot be shifted from P............................ 575
If the electronic key does not operate properly ...................... 576
If the vehicle battery is discharged ................................ 580
If your vehicle overheats .........584
If the vehicle becomes stuck ............................................. 587

5408-1. Essential information
NX200t_OM_USA_OM78081U
Emergency flashers
Press the switch.
All the turn signal lights will flash. To turn
them off, press the switch once again.
■Emergency flashers
If the emergency flashers are used for a long time while the engine is not operating, the
battery may discharge.
The emergency flashers are used to warn other drivers when the vehicle has
to be stopped in the road due to a breakdown, etc.