change time LEXUS RCF 2018 Service Manual

520 7-2. Steps to take in an emergency
RC350_RC300 AWD_RC3 00_RC F_U(OM24748U)Ensure that the shift lever is in P and depress the brake pedal.
Touch the Lexus emblem side of the
electronic key to the engine switch. When the electronic key is detected, a
buzzer sounds and the engine switch
will turn to IGNITION ON mode.
When the smart access system with
push-button start is deactivated in cus-
tomization setting, the engine switch will
turn to ACCESSORY mode.
Firmly depress the brake pedal and check that is shown on the multi-
information display.
Press the engine switch.
In the event that the engine still cannot be started, contact your Lexus dealer.■
Stopping the engine
Shift the shift lever to P and press the engine switch as you normally do when stopping
the engine. ■
Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the electronic
key battery be replaced immediately when the battery is depleted. (  P. 427)■
Changing engine switch modes
Release the brake pedal and press the engine switch in step above.
The engine does not start and modes will be changed each time the switch is pressed.
(  P. 208) ■
When the electronic key does not work properly ●
Make sure that the smart access system wi th push-button start has not been deacti-
vated in the customization setting. If it is off, turn the function on.
(Customizable features:  P. 569)●
Check if battery-saving mode is set. If it is set, cancel the function. (  P. 158)Starting the engine 1
2
3
4
3

574 8-2. Customization
RC350_RC300 AWD_RC3 00_RC F_U(OM24748U)■
Turn signal lever (  P. 221)
* 1
: After flashing the turn signal lights when turn ing left or right while this function is off
and the turn signal lever is moved to the first position in the direction of the flashing
light, the turn signal lights can be selected to be flashing or off.
* 2
: The turn signal lights keep flashing if the tu rn signal lever is moved to the first position
in the direction of flashing light.
* 3
: The turn signal lights will be off if the turn signal lever is moved to the first position in
the direction of flashing light.■
Automatic light control system (  P. 225)
■
Lights (  P. 225) Function Default setting Customized setting
The number of times the turn sig-
nal lights flash automatically
when the turn signal lever is
moved to the first position during
a lane change
* 1
3 5
— O7
Off
* 2
Off
* 3
1 2
Function Default setting Customized setting
Light sensor sensitivity Standard -2 to 2 O O
Time elapsed before headlights
automatically turn off after doors
are closed 30 seconds Off
O O60 seconds
90 seconds 1 2
Function Default setting Customized setting
Daytime running light system
(except Canada) On Off O O 1 2

5778-2. Customization
RC350_RC300 AWD_RC3 00_RC F_U(OM24748U) 8
Vehicle specifications ■
Seat belt reminder (  P. 455)■
Vehicle customization ●
When the smart access system with push-button start is off, the entry unlock function
cannot be customized. ●
When the doors remain closed after unlocking the doors and the timer activated auto-
matic door lock function activates, signals will be generated in accordance with the
operation buzzer volume and operational si gnal (Emergency flashers) function set-
tings. ●
Some settings can be changed using a switch or the Center Display. If a setting is
changed using a switch, the ch anged setting will not be refl ected on the Center Display
screen until the engine switch is turn ed off and then to IGNITION ON mode.■
When customizing usin g the Remote Touch
Stop the vehicle in a safe place, apply the parking brake, and shift the shift lever to P. Also,
to prevent battery discharge, leave the engine running while customizing the features. Function Default setting Customized setting
Vehicle speed linked seat belt
reminder buzzer On Off — O 1 2
WARNING ■
During customization
As the engine needs to be running during customization, ensure that the vehicle is
parked in a place with adequate ventilation. In a closed area such as a garage, exhaust
gases including harmful carbon monoxide (CO) may collect and enter the vehicle. This
may lead to death or a serious health hazard.
NOTICE ■
During customization
To prevent battery discharge, ensure that the engine is running while customizing fea-
tures.