engine LEXUS RX350 2011 Owners Manual

474
4-3. Do-it-yourself maintenance
Battery
Check the battery as follows.
nBattery exterior
Make sure that the battery terminals are not corroded and that there
are no loose connections, cracks, or loose clamps.
Terminals
Hold-down clamp
nBefore recharging
When recharging, the battery produces hydrogen gas which is flammable and
explosive. Therefore, observe the following before recharging:
lIf recharging with the battery installed on the vehicle, be sure to disconnect the
ground cable.
lMake sure the power switch on the charger is off when connecting and discon-
necting the charger cables to the battery.
nAfter recharging/reconnecting the battery
In some cases, the engine may not start. Follow the procedure below to initialize the
system.
Shift the shift lever to P, and turn the “ENGINE START STOP” switch OFF.
Open and close any of the doors.
Start the engine. (If the engine does not start first time, repeat the proce-
dure.)
If the engine will not start even after multiple attempts at the above method, contact
your Lexus dealer.
STEP1
STEP2
STEP3

476
4-3. Do-it-yourself maintenance
NOTICE
nWhen recharging the battery
Never recharge the battery while the engine is running. Also, be sure all accesso-
ries are turned off.

477
4-3. Do-it-yourself maintenance
4

Maintenance and care
Washer fluid
If any washer does not work or the
warning message appears on the
multi-information display, the
washer tank may be empty. Add
washer fluid.
CAUTION
nWhen adding washer fluid
Do not add washer fluid when the engine is hot or running as washer fluid contains
alcohol and may catch fire if spilled on the engine etc.
NOTICE
nDo not use any fluid other than washer fluid
Do not use soapy water or engine antifreeze instead of washer fluid.
Doing so may cause streaking on the vehicle’s painted surfaces.
nDiluting washer fluid
Dilute washer fluid with water as necessary.
Refer to the freezing temperatures listed on the washer fluid tank.

480
4-3. Do-it-yourself maintenance
nHow to initialize the tire pressure warning system
Park the vehicle in safe place and turn the “ENGINE START
STOP” switch off.
While the vehicle is moving, initialization is not performed.
Adjust the tire inflation pressure to the specified cold tire inflation
pressure level. (→P. 6 0 2 )
Make sure to adjust the tire pressure to the specified cold tire inflation
pressure level. The tire pressure warning system will operate based on
this pressure level.
Turn the “ENGINE START STOP” switch to IGNITION ON
mode.
Press and hold the tire pressure
warning reset switch until the tire
pressure warning light flashes
slowly 3 times.
Wait for a few minutes in “ENGINE START STOP” switch to on,
and then turn the “ENGINE START STOP” switch off.
STEP1
STEP2
STEP3
STEP4
STEP5

493
4-3. Do-it-yourself maintenance
4

Maintenance and care
Air conditioning filter
The air conditioning filter must be cleaned or changed regularly to main-
tain air conditioning efficiency.
nRemoval method
Set the air conditioning system to recirculated mode.
(→P. 277)
The air conditioning filter case cannot be removed with the system in
outside air mode.
Turn the “ENGINE START STOP” switch off.
Open the glove box door. Lift
and remove the partition.
Remove the glove box cover.
Remove the filter cover.
STEP1
STEP2
STEP3
STEP4
STEP5

498
4-3. Do-it-yourself maintenance
Checking and replacing fuses
If any of the electrical components do not operate, a fuse may have blown.
If this happens, check and replace the fuses as necessary.
Turn the “ENGINE START STOP” switch off.
Remove the engine compartment cover. (→P. 464)
Open the fuse box cover.
Engine compartment
Push the tab in and lift the lid off.
Driver's side instrument panel
Remove the lid.
After a system failure, see “Fuse layout and amperage ratings”
for details about which fuse to check. (→P. 501)
STEP1
STEP2
STEP3
STEP4

501
4-3. Do-it-yourself maintenance
4

Maintenance and care
Fuse layout and amperage ratings
nEngine compartment
FuseAmpereCircuit
1RDI FAN NO. 180 AElectric cooling fans
2RR DEF50 ARear window defogger
3AIR SUS50 A
4HTR50 AAir conditioning system
5SPARE30 A
6SPARE40 A
7ABS NO. 230 AAnti-lock brake system
8H-LP CLN30 AHeadlight cleaner
9PBD30 APower back door system
10ST30 AStarter system

509
4-3. Do-it-yourself maintenance
4

Maintenance and care
Headlight aim (discharge headlights)
nVertical movement adjustment bolts
Adjustment bolt A
Adjustment bolt B
nBefore checking the headlight aim
Remove the engine compartment cover. (→P. 464)
Make sure the vehicle has a full tank of gas and the area around
the headlight is not deformed.
Park the vehicle on level ground.
Sit in the driver’s seat.
Bounce the vehicle several times.
nAdjusting the headlight aim
Turn bolt A in either direction
using a Phillips-head screw-
driver.
Remember the turning direction
and the number of turns.
STEP1
STEP2
STEP3
STEP4
STEP5
STEP1

511
4-3. Do-it-yourself maintenance
4

Maintenance and care
Light bulbs
You may replace the following bulbs by yourself. The difficulty level of
replacement varies depending on the bulb. If necessary bulb replacement
seems difficult to perform, contact your Lexus dealer.
For more information about replacing other light bulbs, contact your Lexus
dealer.
nPreparing for light bulb replacement
Check the wattage of the light bulb to be replaced. (→P. 605)
nRemoving the engine compartment covers
→P. 4 6 4
nTurning off the power back door main switch (if equipped)
→P. 5 2
nFront bulb locations
Discharge headlights
Front side
marker light
Daytime running light
Front turn
signal light
Parking light

524
5-1. Essential information
Emergency flashers
NOTICE
nTo prevent battery discharge
Do not leave the emergency flashers on longer than necessary when the engine is
not running.
Use the emergency flashers if the vehicle malfunctions or is involved in an
accident.
Press the switch to flash all the
turn signal lights. To turn them
off, press the switch once again.