stop start LEXUS RX350 2011 User Guide

48
1-2. Opening, closing and locking the doors
Locking the front doors from the outside without a key
Move the inside lock button to the lock position.
Close the door.
The door cannot be locked if the “ENGINE START STOP” switch is in
ACCESSORY or IGNITION ON mode, or the electronic key is left
inside the vehicle.
The key may not be detected correctly and the door may be locked.
Rear door child-protector lock
The door cannot be opened from
inside the vehicle when the lock is
set.
These locks can be set to prevent
children from opening the rear
doors. Push down on each rear
door switch to lock both rear
doors.
STEP1
STEP2
nImpact detection door lock release system
In the event that the vehicle is subject to a strong impact, all the doors are unlocked.
Depending on the force of the impact or the type of accident, however, the system
may not operate.
nUsing the mechanical key
The doors can also be locked and unlocked with the mechanical key. (→P. 5 8 1 )
nIf a wrong key is used
The key cylinder rotates freely to isolate inside mechanism.
nCustomization
Settings (e.g. unlocking function using a key) can be changed.
(Customizable features →P. 6 2 1 )

53
1-2. Opening, closing and locking the doors
1

Before driving
nThe power back door can be operated when
lThe back door is unlocked. (Except for using the back door opener button* or
wireless remote control, when the power back door can be operated even if it is
locked.)
lThe power back door main switch is on.
lTo open the power back door when the “ENGINE START STOP” switch is in
IGNITION ON mode, the power back door main switch must be on, the vehi-
cle speed must be lower than 1 mph (3 km/h) and the shift lever must be in P.
*: This setting must be customized at your Lexus dealer.
nBack door handle
nLuggage compartment lights
nBack door closer (vehicles with a power back door)
In the event that the back door is left slightly open, the back door closer will auto-
matically close it to the fully closed position.
lThe back door closer will operate regardless of the “ENGINE START STOP”
switch mode.
lThe back door can be opened while the back door closer is operating by press-
ing the back door opener button.
Use the back door handle when lowering the
back door.
Do not close the back door fully while still
holding the door handle as an injury may
result.
The luggage compartment lights turn on
when the back door is opened with the lug-
gage compartment light switch on.

70
1-3. Adjustable components (seats, mirrors, steering wheel)
Driving position memory∗
Your preferred driving position (the position of the driver's seat, steering
wheel and outside rear view mirrors) can be memorized and recalled with
the touch of a button. It is also possible to set this function to activate auto-
matically when the doors are unlocked.
Three different driving positions can be entered into memory.
nEntering a position to memory
Turn the “ENGINE START STOP” switch to IGNITION ON
mode.
Adjust the driver’s seat, steering wheel and outside rear view
mirrors to the desired positions.
Press the “SET” button, then
within 3 seconds press button
“1”, “2” or “3” until the signal
beeps.
If the selected button has
already been preset, the previ-
ously recorded position will be
overwritten.
nRecalling the memorized position
Check that the shift lever is set in P.
Turn the “ENGINE START STOP” switch to IGNITION ON
mode.
Press button “1”, “2” or “3” until
the signal beeps to recall the
desired position.
STEP1
STEP2
STEP3
STEP1
STEP2
STEP3
∗: If equipped

71
1-3. Adjustable components (seats, mirrors, steering wheel)
1

Before driving
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before performing
the following:
Carry only the key (including the card key) to which you want to link the
driving position. If 2 or more keys are in the vehicle, the driving position
cannot be linked properly.
Shift the shift lever to P and close the driver's door. Turn the
“ENGINE START STOP” switch to IGNITION ON mode.
Press the desired button (“1”, “2” or
“3”) to recall the position. Then,
while keep pressing the button,
press the driver's door lock
switches (either lock or unlock)
until the signal beeps.
The driving position is recalled
when the driver's door is unlocked
using the entry function or wireless
remote control and the driver's
door is opened.
STEP1
STEP2

72
1-3. Adjustable components (seats, mirrors, steering wheel)
nOperating the driving position memory after turning the “ENGINE START
STOP” switch off
Memorized positions (except for the steering wheel position) can be activated up
to 180 seconds after the driver’s door is opened and another 60 seconds after it is
closed again, even after turning the “ENGINE START STOP” switch off.
nCanceling the linked door unlock operation
Turn the “ENGINE START STOP” switch to IGNITION ON mode and
close the driver's door.
While pressing the “SET” button, press the driver’s door lock switches
(either lock or unlock) until the signal beeps.
nStopping seat position operation part-way through
Perform any of the following operations:
lPress the “SET” button.
lPress button “1”, “2” or “3”.
lAdjust the seat using the switches (only cancels seat position recall).
lAdjust the steering wheel using the tilt and telescopic steering control switch
(only cancels steering wheel position recall).
nCorrect seat position
When the seat is in the most forward or most backward position, and the seat is
being moved in those directions, the system may not correctly recognize the cur-
rent position and the memorized position will not be correctly recalled.
nWhen the power easy access system (→P. 63) is activated
If a seat position is memorized, the driver seat will move back the set distance
(→P. 621) from that memorized position.
CAUTION
nSeat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passenger
or squeeze your body against the steering wheel.
STEP1
STEP2

83
1
1-3. Adjustable components (seats, mirrors, steering wheel)

Before driving
Steering wheel
Auto tilt away
When the “ENGINE START
STOP” switch is turned off, the
steering wheel returns to its
stowed position by moving up and
away to enable easier driver entry
and exit.
Turning the “ENGINE START
STOP” switch to ACCESSORY or
IGNITION ON mode will return
the steering wheel to the original
position.
The steering wheel can be adjusted to a comfortable position.
Operating the switch moves the steering wheel in the following direc-
tions:
Up
Down
Away from the driver
Toward the driver

84
1-3. Adjustable components (seats, mirrors, steering wheel)
nThe steering wheel can be adjusted when
The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON
mode*.
*: Vehicles with driving position memory: If the driver's seat belt is fastened, the
steering wheel can be adjusted regardless of “ENGINE START STOP” switch
mode.
nAutomatic adjustment of the steering position (vehicles with driving position
memory)
A desired steering position can be entered to memory and recalled automatically
by the driving position memory. (→P. 7 0 )
nNotes for the auto tilt away function (vehicles with driving position memory)
The auto tilt away function can only operate when the “ENGINE START STOP”
switch has been turned off, the driver seat belt has been unfastened and the driver’s
seat movement (→P. 621) is in a setting other than off.
When the driver fastens the seat belt again, the steering wheel will return to the
original position. (→P. 6 3 )
CAUTION
nCaution while driving
Do not adjust the steering wheel while driving.
Doing so may cause the driver to mishandle the vehicle and cause an accident,
resulting in death or serious injury.

85
1
1-3. Adjustable components (seats, mirrors, steering wheel)

Before driving
Anti-glare inside rear view mirror
Adjusting the height of rear view mirror
Adjust the height of the rear view
mirror by moving it up and down.
In automatic mode, sensors are used to detect the headlights of vehicles
behind and the reflected light is automatically reduced.
Turns automatic mode on/ off
The indicator comes on when
automatic mode is turned on.
The mirror will revert to auto-
matic mode each time the
“ENGINE START STOP” switch
is turned to IGNITION ON
mode.Indicator
nTo prevent sensor error
To ensure that the sensors operate properly,
do not touch or cover them.

88
1-3. Adjustable components (seats, mirrors, steering wheel)
Automatically folding and extending the mirrors (if equipped)
nUsing the switch
Press the switch to fold the mirrors.
Press it again to return them.
nSetting automatic mode
Automatic mode allows the folding
or extending of the mirrors to be
linked to locking/unlocking of the
doors.
Press the “AUTO” button to set
automatic mode.
The indicator will come on.
Indicator
nMirror angle can be adjusted when
The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.
nLinked mirror function when reversing
The outside rear view mirrors will automatically angle downwards when the vehicle
is reversing in order to give a better view of the ground. This function only operates
when either the “L” or “R” mirror select button is selected.
nWhen the mirrors are fogged up
Turn on the mirror defoggers to defog the mirrors. (→P. 2 8 1 )

91
1-4. Opening and closing the windows and moon roof
1

Before driving
nThe power windows can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
nOperating the power windows after turning the engine off
The power windows can be operated for approximately 45 seconds even after the
“ENGINE START STOP” switch is turned to ACCESSORY mode or turned off.
They cannot, however, be operated once either front door is opened.
nJam protection function
If an object becomes caught between the window and the window frame, window
travel is stopped and the window is opened slightly.
nWhen the power window does not close normally
If the jam protection function is operating abnormally and a window cannot be
closed, perform the following operations using the power window switch on the rel-
evant door.
lAfter stopping the vehicle, the window can be closed by holding the power win-
dow switch in the one-touch closing position while the “ENGINE START
STOP” switch is turned to IGNITION ON mode.
lIf the window still cannot be closed even by carrying out the operation
explained above, initialize the function by performing the following procedure.
Hold the power window switch in the one-touch closing position. Con-
tinue holding the switch for a further 6 seconds after the window has
closed.
Hold the power window switch in the one-touch opening position. Con-
tinue holding the switch for a further 2 seconds after the window has
opened completely.
Hold the power window switch in the one-touch closing position once
again. Continue holding the switch for a further 2 seconds after the win-
dow has closed.
If you release the switch while the window is moving, start again from the beginning.
If the window continues to close but then re-open slightly even after performing the
above procedure correctly, have the vehicle inspected by your Lexus dealer.
STEP1
STEP2
STEP3