ignition switch LEXUS SC400 1991 Service Owners Manual

Troubleshooting
You will find the cause of trouble more easily by properly using the tabl\
e shown below. In this table, the numbers
indicate the order of priority of the causes of trouble. Check each part in the \
order shown. If necessary, replace
the part.
See page
BE±4,21BE±4,21BE±4,20BE±4,20BE±156BE±152BE±180BE±179BE±179 ±±BE±181BE±26BE±79BE±4,20 ±±
Part
name
Trouble
AM1 FuseDOME FuseDOOR FusePOWER FuseTheft Deterrent and Door Lock Control ECUPower Window Main RelaySliding Roof Control RelaySliding Roof SwitchSliding Roof MotorSliding Rood Motor (Stones to foreign material
trapped in motor assembly)Limit SwitchIgnition SwitchDoor Courtesy SwitchECU±IG FuseWire Harness
*1 Sliding roof system does not operate.1234
*2 Sliding roof system does not operate.35467892110
Sliding roof system operates abnormally.1324
Sliding roof system stops operation half way.1342
Buzzer does not sound.123
Buzzer sounds abnormally.1
ªKey±off Sliding Roofº operation does not
operate.124536
*1: Door Lock does not operate
*2: Door Lock is normal
BE±182
±
BODY ELECTRICAL SYSTEM Sliding Roof System
WhereEverybodyKnowsYourName

INSPECTION OF MIRROR ECU
1. INSPECT MIRROR ECU CIRCUITDisconnect the connectors from the ECU and inspect the
connector on the wire harness side as shown in the chart be-
low.
Check forTester connectionConditionSpecified value
ContinuityA1±A2ConstantContinuity
A1±A3ConstantContinuity
A8±A10ConstantContinuity
A9±A10ConstantContinuity
A11±GroundConstantContinuity
A12±A13ConstantContinuity
A16±*ConstantContinuity
B1±B2Right mirror switch on DOWNContinuity
B1±B4Right mirror switch to RIGHTContinuity
B1±B5Left mirror switch to RIGHTContinuity
B1±B6Left mirror switch to DOWNContinuity
B2±B3Right mirror switch to UPContinuity
B3±B4Right mirror switch to LEFTContinuity
B3±B5Left mirror switch to LEFTContinuity
B3±B6Left mirror switch to UPContinuity
VoltageA4±GroundConstantBattery positive voltage
A7±GroundIgnition switch to ACCBattery positive voltageA7±GroundIgnition switch to OFFNo voltage
*: Terminal 1/18 of the Tilt and Telescopic ECU
If circuit is not as specified, inspect the wire harness and mir-
ror switch or motor assembly.
BE±188
±
BODY ELECTRICAL SYSTEM Power Mirror Control System
WhereEverybodyKnowsYourName

(Circuit)
Disconnect the control panel connector and inspect the con-
nector on wire harness side as shown.
Check forTester connectionConditionSpecified value
Voltage2±GroundLight control switch positionTAIL or HEADBattery voltage
OFFNo voltage
If circuit is not as specified, refer to BE±199, 201, 203 wiring
diagrams and inspect the circuits connected to other parts.
(Radio Receiver Assembly)
REMOVAL AND INSTALLATION OF
RADIO RECEIVER ASSEMBLY
(See page BE±112)
INSPECTION OF RADIO RECEIVER
ASSEMBLY
INSPECT RADIO RECEIVER ASSEMBLY
(Circuit)
Disconnect the connectors from the radio receiver assembly.
And inspect the connector on the wire harness side as
shown.
(without CD player)
Check forTester connectionConditionSpecified value
ContinuityA7±GroundConstantContinuity
VoltageA4±GroundConstantBattery voltage
VoltageA3±GroundIgnition switch positionACC or ONBattery voltageg
LOCKNo voltage
A10±GroundLight control switch positionTAIL or HEADBattery voltageg
OFFNo voltage
If circuit is not as specified, refer to BE±199 wiring diagrams
and inspect the circuits connected to other parts.
±
BODY ELECTRICAL SYSTEM Audio SystemBE±207
WhereEverybodyKnowsYourName

(With CD player)
Check forTester connectionConditionSpecified value
VoltageA4±GroundConstantBattery voltage
A3±GroundIgnition switch positionACC or ONBattery voltageg
LOCKNo voltage
A2±GroundLight control switchTAIL or HEADBattery voltageg
positionOFFNo voltage
If circuit is not as specified, refer to BE±201, 203 wiring dia-
grams and inspect the circuits connected to other parts.
HINT: Check the wire harness between radio receiver assem-
bly and the CD auto changer, between radio receiver assem-
bly and power amplifier, in accordance with the wiring dia-
grams in BE±201, 203.
(Front Door Speaker)
REMOVAL AND INSTALLATION OF
FRONT DOOR SPEAKER
(See page BO±35)
(Tweeter)
REMOVAL AND INSTALLATION OF
TWEETER
(See page BO±34)
(Rear Speaker)
REMOVAL AND INSTALLATION OF
REAR SPEAKER
1. REMOVE REAR SPEAKER
(a) Remove the package tray trim.
HINT: (See page BO±124)
(b) Remove eight bolts.
(c) Disconnect connectors and remove the rear speaker.
2. INSTALL REAR SPEAKER For installation, follow the removal procedure in reverse.
BE±208
±
BODY ELECTRICAL SYSTEM Audio System
WhereEverybodyKnowsYourName

(c) Disconnect the connector and remove the wooferamplifier.
2. INSTALL WOOFER AMPLIFIER For installation, follow the removal procedure in reverse.
INSPECTION OF WOOFER AMPLIFIER
INSPECT WOOFER AMPLIFIER
(Circuit)
Disconnect the connector from woofer amplifier and inspect
the connector on the wire harness side as shown.
Check forTester connectionConditionSpecified value
Continuity7±GroundConstantContinuity
Voltage3±GroundConstantBattery voltage
4±GroundIgnition switch positionACC or ONBattery voltage
6±Ground
g
LOCKNo voltage
If circuit is not as specified, refer to BE±201 wiring diagrams
and inspect the circuits connected to other parts.
(Power Amplifier)
REMOVAL AND INSTALLATION OF
POWER AMPLIFIER
(Pioneer)
1. REMOVE POWER AMPLIFIER (a) Remove the RH side cover.
(b) Remove the CD auto changer (See page BE±212).
(c) Disconnect two connectors and remove three nuts and the power amplifier with the bracket.
(d) Remove four bolts and the power amplifier.
2. INSTALL POWER AMPLIFIER For installation, follow the removal procedure in reverse.
BE±210
±
BODY ELECTRICAL SYSTEM Audio System
WhereEverybodyKnowsYourName

(Nakamichi)
1. REMOVE POWER AMPLIFIER
(a) Remove the RH side cover.
(b) Remove the CD auto changer (See page BE±212).
(c) Disconnect three connectors and remove three nuts and the power amplifier with the bracket.
(d) Remove four bolts and the power amplifier.
2. INSTALL WOOFER AMPLIFIER For installation follow the removal procedure in reverse.
POWER AMPLIFIER INSPECTION
INSPECT POWER AMPLIFIER
(Circuit)
Disconnect the connector from power amplifier and inspect
the connector on the wire harness side as shown.
(Produced by PIONEER)
 Check for Tester connection Condition Specified value
 Continuity B7±Ground Constant Continuity
 Voltage B10±Ground Constant Battery positive voltage
  A14±Ground
A6 G d
 Ignition switch position ACC or ON Battery positive voltage  A6±Ground  LOCK No voltage
If circuit is not as specified, refer to BE±201 wiring diagrams
and inspect the circuits connected to other parts.
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEMBE±211
WhereEverybodyKnowsYourName

(Produced by NAKAMICHI)
 Check for Tester connection Condition Specified value 

Continuity 

B7±Ground
C7±Ground 


Constant


Continuity
 

Voltage 

B10±Ground
C3±Ground 


Constant


Battery positive voltage
 


 

A6±Ground
A14±Ground 


Ignition switchposition
 


ACC or ON

Battery positive voltage
 


 


C4±Ground
C6±Ground 


Ignition switch position 


LOCK

No voltage
If circuit is not as specified, refer to
BE±203 wiring diagrams
and inspect the circuits connected to other parts.
CD AUTO CHANGER
CD AUTO CHANGER REMOVAL AND
INSTALLATION
1. REMOVE CD AUTO CHANGER (a) Remove RH side cover.
(b) Disconnect two connectors.
(c) Remove three bolts, one nut and the CD auto changer.
CD AUTO CHANGER INSPECTION
INSPECT CD AUTO CHANGER(Circuit)
Disconnect connectors from CD auto changer and inspect
the connector on the wire harness side as shown.
BE±212
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEM
WhereEverybodyKnowsYourName

 
Check for Tester connection Condition Specified value
 Voltage A4±Ground Constant Battery positive voltage
  
A3±Ground
 Ignition switch
iti
 ACC or ON Battery positive voltage
  A3±Ground position LOCK No voltage
 Continuity 
A7±Ground
 Luggage compartment
d t it h
 Push (OFF) No continuity  A7±Ground door courtesy switch Free (ON) Continuity
If circuit is not as specified, refer to BE±201, 203 wiring dia-
grams and inspect the circuits connected to other parts.
HINT:
w Check the wire harness between the radio receiver
assembly and the CD auto changer in accordance with
the wiring diagrams in BE±201, 203.
w Since the signals to and from the CDL+, CDL, CDR+,
CDR, TXM+, TXM, TXS+ and TXS terminals are serial
signals, they cannot ordinarily be measured with a
tester.
LUGGAGE COMPARTMENT DOOR
COURTESY SWITCH
(See page BE±82)
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEMBE±213
WhereEverybodyKnowsYourName

MOTOR ANTENNA
MOTOR ANTENNA REMOVAL AND
INSTALLATION
1. REMOVE MOTOR ANTENNA
(a) Remove the antenna nut.
(b) Remove the LH side cover.
(c) Disconnect the motor antenna connector and the antennacord.
(d) Remove the nut and the motor antenna assembly.
2. INSTALL MOTOR ANTENNA
(a) Install the antenna nut.
(b) Connect the motor antenna connector and the antenna cord.
(c) Install the nut.
ANTENNA ROD REMOVAL AND
INSTALLATION
1. REMOVE ANTENNA ROD HINT: Perform this operation with the battery negative (±)
cable connected to the battery terminal.
(a) Turn the ignition switch to ºLOCKº position.
(b) Remove the antenna nut.
(c±1) with CD player
Press the ºAMº and ºCDº buttons on the radio receiver, and
simultaneously turn the ignition switch to ºACCº position.
(c±2) without CD player Press the ºAMº and ºT APEº buttons on the radio receiver, and
simultaneously turn the ignition switch to ºACCº position.
HINT:
w The rod will extend fully and be released from the motor
antenna.
w After removing the antenna rod, leave the ignition switch
at ºACCº.
NOTICE: To prevent body damage when the antenna rod is re-
leased, hold the rod while it comes out.
BE±214±
BODY ELECTRICAL SYSTEM AUDIO SYSTEM
WhereEverybodyKnowsYourName

2. INSTALL ANTENNA ROD
(a) Insert the cable of the rod until it reaches the bottom.HINT:
wWhen inserting the cable, the teeth on the cable must
face toward the rear of the vehicle.
w Insert the cable approx. 400 mm (15.75 in.).
(b) Wind the cable to retract the rod by turning the ignition switch
to ºLOCKº position.
HINT:
w If the ignition switch is already in ºLOCKº position,
perform step 1.
w In case the cable is not wound, twist it as shown in the
illustration.
w Even if the rod has not retracted fully, install the ant enna
nut and inspect the antenna rod operation. It will finally
retract fully.
(c) Inspect the antenna rod operation by pushing the radio wave
band select buttons.
MOTOR ANTENNA INSPECTION
1. INSPECT MOTOR ANTENNA (Circuit)
Disconnect the motor antenna connector from the body wire
harness and inspect the connector on body wire harness side
as shown.
 Check for Tester connection\
\
Condition Specified value
 Continuity 7±Ground\
\
Constant Continuity
 Voltage 3±Ground\
\
Constant Battery positive voltage
 
g
 8±Ground Ignition switch ACC or ON Battery positive voltage
  8±Ground 
g
position LOCK No voltage
  6±Ground Ignition switch ON Battery positive voltage
  6±Ground 
g
position ACC or LOCK No voltage
  2±Ground Ignition switch Radio or Tape or CD switch ON Battery positive voltage
  2±Ground 
g
ACC or ON Radio or Tape or CD switch OFF No voltage
  5±Ground Ignition switch Radio switch ON Battery positive voltage
  5±Ground 
g
ACC or ON Radio switch OFF No voltage
  
4±Ground
 Ignition switch
ACC or ON and
 AM or FM (87.9 ± 96.0 MHz) Battery positive voltage
  4±Ground ACC or ON and
radio switch ON Others No voltage
 


 

1±Ground
 

Ignition switch
ACC or ON and 

AM
 

Battery positive voltage
   radio switch ON Others No voltage
If circuit is not as specified, inspect radio or wire harness. If
circuit is as specified, replace motor antenna.
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEMBE±215
WhereEverybodyKnowsYourName