ignition switch LEXUS SC400 1991 Service Repair Manual

159
RETURN OPERATION
WHEN THE SEAT BACK IS RAISED UP FROM THE WALK±IN POSITION AND RETURNED TO THE UPRIGHT LOCK POSITION,
RECLINING LIMIT SWITCH NO. 1 OPERATES AND A SIGNAL IS INPUT TO TERMINAL RRSW OF THE POWER SEAT ECU " TERMINAL
SLD± " TERMINAL 2 OF POWER SEAT MOTOR (FOR PASSENGER'S SEAT SLIDE CONTROL) " MOTOR " TERMINAL 1 " TERMINAL
SLD+ OF ECU " TERMINAL GND " GROUND . THIS CAUSES THE SEAT TO SLIDE BACK TO A POSITION 120 MM FROM THE MOST
REAR POSITION, COMPLETING RETURN OPERATION. HOWEVER, IF THE SEAT IS POSITIONED WITHIN 120 MM OF THE MOST REAR
POSITION, RETURN OPERATION DOES NOT OCCUR, THUS MAINTAINING SUFFICIENT SPACE FOR THE REAR SEAT PASSENGER.
D10 DOOR LOCK MOTOR, DOOR UNLOCK DETECTION SW AND DOOR OPEN DETECTION SW LH
3±6 : CLOSED WITH FRONT LH DOOR OPEN
N 1 A/T INDICATOR SW [NEUTRAL START SW]
9±1 : CLOSED WITH SHIFT LEVER AT ªPº POSITION
P10(A), P11(B) POWER SEAT ECU (FOR DRIVER'S SEAT)
(A) 6±GROUND : APPROX. 12 VOLTS WITH STOP LIGHT SW ON
(B) 7±GROUND : ALWAYS APPROX. 12 VOLTS
(A) 7±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON
(A) 15±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON AND SHIFT LEVER AT ªPº RANGE
(A) 2±GROUND : APPROX. 12 VOLTS WITH DRIVER'S SEAT AT FRONT SLIDE OPERATION
(A) 9±GROUND : APPROX. 12 VOLTS WITH DRIVER'S SEAT AT REAR SLIDE OPERATION
(A) 4±GROUND : APPROX. 12 VOLTS WITH DRIVER'S SEAT AT FRONT VERTICAL UP OPERATION
(A) 11±GROUND : APPROX. 12 VOLTS WITH DRIVER'S SEAT AT FRONT VERTICAL DOWN OPERATION
(A) 13±GROUND : APPROX. 12 VOLTS WITH DRIVER'S SEAT AT REAR VERTICAL UP OPERATION
(A) 12±GROUND : APPROX. 12 VOLTS WITH DRIVER'S SEAT AT REAR VERTICAL DOWN OPERATION
(B) 18±GROUND : ALWAYS CONTINUITY
(A) 5, (A) 14±GROUND : ALWAYS APPROX. 12 VOLTS
(A) 1, (A) 8±GROUND : ALWAYS CONTINUITY
P 8 POWER SEAT CONTROL SW (FOR DRIVER'S SEAT)
4±14 : CLOSED WITH DRIVER'S SEAT AT FRONT RECLINING OPERATION
3±14 : CLOSED WITH DRIVER'S SEAT AT REAR RECLINING OPERATION
1±14 : CLOSED WITH DRIVER'S SEAT AT FRONT SLIDE OPERATION
2±14 : CLOSED WITH DRIVER'S SEAT AT REAR SLIDE OPERATION
5±14 : CLOSED WITH DRIVER'S SEAT AT FRONT VERTICAL UP OPERATION
6±14 : CLOSED WITH DRIVER'S SEAT AT FRONT VERTICAL DOWN OPERATION
9±14 : CLOSED WITH DRIVER'S SEAT AT REAR VERTICAL UP OPERATION
8±14 : CLOSED WITH DRIVER'S SEAT AT REAR VERTICAL DOWN OPERATION
P12 POWER SEAT ECU (FOR PASSENGER'S SEAT)
1±GROUND : ALWAYS APPROX. 12 VOLTS
8±GROUND : ALWAYS APPROX. 12 VOLTS
7±GROUND : APPROX. 12 VOLTS WITH PASSENGER'S SEAT AT FRONT SLIDE OPERATION
17±GROUND : APPROX. 12 VOLTS WITH PASSENGER'S SEAT AT REAR SLIDE OPERATION
S12 STOP LIGHT SW
2±1 : CLOSED WITH STOP LIGHT SW ON
SERVICE HINTS
WhereEverybodyKnowsYourName

172
REMOTE CONTROL MIRROR (w/ DRIVING POSITION MEMORY)
CURRENT IS ALWAYS APPLIED TO TERMINAL +B OF REMOTE CONTROL MIRROR ECU THROUGH THE ECU±B FUSE.
WHEN THE IGNITION SW IS TURNED TO ON OR ACC POSITION, THE CURRENT FLOWS TO TERMINAL ACC OF THE REMOTE
CONTROL MIRROR ECU THROUGH THE RADIO NO. 2 FUSE.
REMOTE CONTROL MIRROR OPERATION
WHEN THE IGNITION SW IS TURNED TO ON OR ACC POSITION, THE REMOTE CONTROL MIRROR ECU OPERATES. WHEN THE
SELECT SW OF THE REMOTE CONTROL MIRROR SW IS MOVED TO THE LH POSITION AND THE OPERATION SW IS MOVED TO
ªLEFTº SIDE, A SIGNAL IS INPUT FROM TERMINAL SWO2 OF REMOTE CONTROL MIRROR ECU TO TERMINAL 2 OF REMOTE
CONTROL MIRROR SW " TERMINAL 12 "TERMINAL SWI2 OF ECU.
AS A RESULT, THE CURRENT TO TERMINAL +B OF ECU FLOWS FROM TERMINAL MHL OF ECU "TERMINAL 1 OF REMOTE
CONTROL MIRROR LH " MOTOR " TERMINAL 2 "TERMINAL M+L OF ECU "TERMINAL GND "GROUND , ROTATING THE MOTOR
TO ADJUST THE ANGLE OF THE LEFT SIDE OF THE OUTER MIRROR (DRIVER'S).
TO CHANGE THE ANGLE OF THE RIGHT SIDE OF THE MIRROR, THE OPERATION SW OF THE REMOTE CONTROL MIRROR SW IS
MOVED TO THE ªRIGHTº SIDE.
THEN, A SIGNAL IS INPUT FROM TERMINAL SWO2 OF REMOTE CONTROL MIRROR ECU " TERMINAL 2 OF REMOTE CONTROL
MIRROR SW " TERMINAL 8 "TERMINAL SWI1 OF ECU. AS A RESULT, THE CURRENT TO TERMINAL +B OF REMOTE CONTROL
MIRROR ECU FLOWS FROM TERMINAL M+L OF ECU " TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR " TERMINAL 1 "
TERMINAL MHL OF ECU " TERMINAL GND " GROUND, CAUSING THE ANGLE OF THE OUTER MIRROR (DRIVER'S) TO CHANGE ON
THE RIGHT SIDE.
THE MOVEMENT TO OTHER POSITIONS OCCURS SIMILARLY, SO ONLY THE CURRENT FLOW TO EACH MOTOR IS SHOWN:
SELECT SW RH POSITION, OPERATION SW LEFT POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL MHR "TERMINAL 1 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+R OF ECU "TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW RIGHT POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL M+R "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 1 "TERMINAL MHR OF ECU " TERMINAL GND "GROUND .
SELECT SW LH POSITION, OPERATION SW UP POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU " TERMINAL MVL " TERMINAL 3 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+L OF ECU "TERMINAL GND "GROUND .
SELECT SW LH POSITION, OPERATION SW DOWN POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL M+L "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 3 "TERMINAL MVL OF ECU " TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW UP POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR "TERMINAL MVR "TERMINAL 3 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+R OF ECU "TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW DOWN POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR "TERMINAL M+R "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 3 "TERMINAL MVR OF ECU " TERMINAL GND "GROUND .
THE NUMBER OF TURNS OF EACH MOTOR (AMOUNT OF MOVEMENT OF EACH PART OF THE MIRROR) IS DETECTED BY THE
POSITION SENSORS AND INPUT TO THE ECU, MAKING IT POSSIBLE TO PERFORM MEMORY AND RETURN FUNCTIONS FOR THE
MIRROR POSITION USING THE DRIVING POSITION MEMORY AND RETURN SWITCH.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName

181
THE SRS (SUPPLEMENTAL RESTRAINT SYSTEM) AIRBAG IS A DRIVER PROTECTION DEVICE WHICH HAS A SUPPLEMENTAL ROLE
TO THE SEAT BELTS.
CURRENT FLOWS CONSTANTLY TO TERMINAL 6 OF THE CENTER AIRBAG SENSOR ASSEMBLY. WHEN THE IGNITION SW IS
TURNED TO ACC OR ON, CURRENT FROM THE CIG FUSE FLOWS TO TERMINAL 14 OF THE CENTER AIRBAG SENSOR ASSEMBLY.
ONLY WHEN THE IGNITION SW IS ON DOES THE CURRENT FROM THE IGN FUSE TO TERMINAL 7 .
IF AN ACCIDENT OCCURS WHILE DRIVING, DECELERATION CAUSED BY A FRONTAL IMPACT IS DETECTED BY EACH SENSOR AND
SWITCH, AND WHEN THE FRONTAL IMPACT EXCEEDS A SET LEVEL (WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG
SENSOR ASSEMBLY IS ON AND THE CENTER AIRBAG SENSOR IS ON, FRONT AIRBAG SENSORS ARE OFF), CURRENT \
FROM THE
CIG OR IGN FUSE FLOWS TO TERMINAL 11 OF THE CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG SQUIB "
SQUIB " TERMINAL 2 " TERMINAL 10 OF CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 8, TERMINAL 13 OR BODY GROUND
" GROUND.
WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON AND THE FRONT AIRBAG SENSOR LH OR
RH IS ON, CENTER AIRBAG SENSOR IS OFF AND CURRENT FROM THE CIG OR IGN FUSE FLOWS TO TERMINAL 11 OF THE CENTER
AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG SQUIB " SQUIB " TERMINAL 2 " TERMINAL 10 OF CENTER AIRBAG
SENSOR ASSEMBLY " TERMINAL 3 OR 4 " TERMINAL 1 OF FRONT AIRBAG SENSOR " TERMINAL 2 " TERMINAL 2 OR 5 OF
CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 8, TERMINAL 13 OR BODY GROUND " GROUND , WHEN THE SAFING SENSOR
BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON, AND THE FRONT AIRBAG SENSOR LH OR RH IS ON AND CENTER
AIRBAG SENSOR IS ON ONE OF THE ABOVE±MENTIONED CIRCUITS IS ACTIVATED SO THAT CURRENT FLOWS TO THE AIRBAG
SQUIB AND CAUSES IT TO OPERATE. THE BAG STORED INSIDE THE STEERING WHEEL PAD IS INSTANTANEOUSLY EXPANDED TO
SOFTEN THE SHOCK TO THE DRIVER.
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A2928C1228T 629
C 326F 126
C1028F 226
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1E20INSTRUMENT PANEL WIRE
1G20COWL NO. 2 WIRE
1J20COWL WIRE
3A
3B
3D22INSTRUMENT PANEL WIRE
3E
3H
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IK136ENGINE WIRE AND INSTRUMENT PANEL WIRE (RIGHT KICK PANEL)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC34FRONT SIDE OF INTAKE MANIFOLD
ED34REAR SIDE OF CYLINDER HEAD RH
IF36LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E2034ENGINE WIRE
SYSTEM OUTLINE
WhereEverybodyKnowsYourName