belt LEXUS SC400 1991 Service Owner's Manual

Quarter Window Glass with Moulding
REMOVAL AND INSTALLATION
(See page BO±101)
1. REMOVE FOLLOWING PARTS: (See steps 5 to 8 on pages BO±123 to 124)
(a) Rear seat cushion
(b) Rear seat back
(c) Quarter trim
(d) Roof side inner garnish
(e) Shoulder belt anchor
2. REMOVE QUARTER WINDOW GLASS (See page BO±52)
3. INSTALL QUARTER WINDOW GLASS (See page BO±53)
4. INSTALL FOLLOWING PARTS: Install the parts following removal sequence in reverse.
Rocker Panel Moulding
REMOVAL AND INSTALLATION
(See page BO±101)
1. REMOVE ROCKER PANEL MOULDING (a) Remove two screws.
(b) Pry l oose clips and remove the moulding onto the panel.
2. INSTALL ROCKER PANEL MOULDING (a) Insert the top of clips into the panel hole and tap themoulding onto the panel.
(b) Install two screws.
Front Fender Wheel Opening Moulding
REMOVAL AND INSTALLATION
(See page BO±101)
1. REMOVE FRONT FENDER WHEEL OPENING MOULDING
Remove eight screws and the moulding.
2. INSTALL FRONT FENDER WHEEL OPENING MOULDING Install eight screws and the moulding.
Quarter Wheel Opening Moulding
REMOVAL AND INSTALLATION
(See page BO±101)
HINT: Do the same manner as the front fender wheel
opening moulding.
BO±102
±
BODY Moulding (Body Outside Moulding)
WhereEverybodyKnowsYourName

REMOVAL OF FLOOR CARPET
1. REMOVE FOLLOWING PARTS:
wFront seat (See step 3 on page BO±58)
wRear seat (See steps 1 to 2 on page BO±66)
wRoof side inner garnish (See step 8 on page BO±123)
wFront pillar garnish (See step 2 on page BO±122)
wFront scuff plate (See step 11 on page BO±123)
wConsole box (See step 14 on page BO±111)
2. REMOVE FLOOR CARPET (a) Using a clip remover, remove the clips.
(b) Remove the front seat belt lower bolt.
[Driver 's Side]
(c) Raise the end of the carpet and disconnect the hook.
[Passenger 's Side]
(d) Raise the end of the carpet and disconnect the hook.
(e) Slide the carpet backward and remove it.
±
BODY Floor CarpetBO±117
WhereEverybodyKnowsYourName

INSTALLATION OF FLOOR CARPET
(See page BO±117)
INSTALL FLOOR CARPET PARTS BY FOLLOWING REMOVAL
SEQUENCE IN REVERSE HINT: Torque following parts.
(a) Front seat belt lower anchor bolt
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
(b) Front Seat
Torque: 37 N Vm (375 kgf Vcm, 27 ft Vlbf)
BO±118±
BODY Floor Carpet
WhereEverybodyKnowsYourName

REMOVAL OF ROOF HEADLINING
(See page BO±119)
1. REMOVE FOLLOWING PARTS:
wFront pillar garnish
wSun visor
wRear seat back and cushion
wRoof side inner garnish
wQuarter trim
wInterior Light
wCenter visor
2. REMOVE ROOF HEADLINING (a) Disconnect four clips from the roof panel rear end.
(b) Using a clip remover, remove six clips.
(c) R e l e a s e t h e f a s t ener tapes, then remove the
headlining.
(d) Fully recline the front seat back.
(e) Bring out the headlining as shown.
NOTICE: Do not fold down the headlining.
INSTALLATION OF ROOF HEADLINING
(See page BO±119)
INSTALL ROOF HEADLINING PARTS BY FOLLOWING RE-
MOVAL SEQUENCE IN REVERSE HINT: Torque following parts:
(a) Rear seat back
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(b) Rear seat belt inner belt
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
(c) Front seat belt shoulder anchor bolt
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
BO±120±
BODY Roof Headlining
WhereEverybodyKnowsYourName

REMOVAL OF TRIM, ASSIST GRIP AND
VISOR
(See page BO±121)
1. REMOVE ASSIST GRIP (a) Lift up the grip so that the screwdriver can be inserted.
(b) Insert the screwdriver into the groove in the cushion.
(c) Turn the screwdriver while pulling the assist grip upward.
(d) After the top of the assist grip is freed, pull the lower part
downward.
2. REMOVE FRONT PILLAR GARNISH (a) Remove two screws and the assist grip.
(b) Pry out clips by your hand.
(c) Pull the garnish upward to remove it.
3. REMOVE SUN VISOR (a) Pry out the cover.
(b) Remove two screws, disconnect the connector and thesun visor.
(c) Remove the screw and the holder.
4. REMOVE CENTER VISOR (a) Pry out the cover.
(b) Remove two screws, disconnect the connector and thevisor.
5. REMOVE REAR SEAT CUSHION AND BACK
6. REMOVE FRONT SEAT OUTER BELT
7. REMOVE QUARTER TRIM AND ASSIST GRIP (a) Remove two caps, two screws and assist grip.
(b) Remove the clip and the belt guide.
(c) Remove the bolt and the front seat belt anchor.
BO±122
±
BODY Trim, Assist Grip and Visor
WhereEverybodyKnowsYourName

(d) Using a clip remover, remove three clips.
(e) Insert a screwdriver between the retainers and quartertrim to pry it loose.
(f) Remove the quarter trim.
8. REMOVE ROOF SIDE INNER GARNISH (a) Remove four screws.
(b) Insert a screwdriver between the retainers and innergarnish to pry it loose.
(c) Remove the inner garnish.
9. REMOVE PACKAGE TRAY TRIM (a) Using a clip remover, remove two clips.
(b) Pull the belt guide forward to remove it.
(c) Pull the trim forward to remove it.
10. REMOVE ROOM PARTITION TRIM
11. REMOVE FRONT SCUFF PLATE Using a screwdriver, remove the plate.
HINT: Tape the screwdriver tip before use.
12. REMOVE OUTSIDE SCUFF PLATE Insert a screwdriver between the retainers and the plate to
pry it loose.
HINT: Tape the screwdriver tip before use.
±
BODY Trim, Assist Grip and VisorBO±123
WhereEverybodyKnowsYourName

13. (w/ Sliding Roof)REMOVE SUN SHADE TRIM
(See steps 1 to 10 on pages BO±85 to 86)
INSTALLATION OF TRIM, ASSIST GRIP
AND VISOR
(See page BO±121)
1. (w/ Sliding Roof) INSTALL SUN SHADE TRIM
2. INSTALL OUTSIDE SCUFF PLATE Place the plate on the body and install it by tapping.
3. INSTALL FRONT SCUFF PLATE Place the plate on the body and install it by tapping.
4. INSTALL ROOM PARTITION TRIM Install the trim as shown.
5. INSTALL PACKAGE TRAY TRIM (a) Align the six retainers with the holes of the panel, thenpush the trim backward.
(b) Install two clips.
(c) Install the belt guide to the trim.
BO±124
±
BODY Trim, Assist Grip and Visor
WhereEverybodyKnowsYourName

6. INSTALL ROOF SIDE INNER GARNISH(a) Place the inner garnish on the quarter panel and installit by tapping it in.
(b) Install four screws.
7. INSTALL QUARTER TRIM AND ASSIST GRIP (a) Place the trim on the quarter panel and install it bytapping it in.
(b) Install the belt guide with the clip.
(c) Install the front seat belt anchor with the bolt.
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
(d) Install the assist grip with two screws and two caps.
8. INSTALL REAR SEAT CUSHION AND BACK (See page BO±67)
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
9. INSTALL CENTER VISOR
(a) Connect the connector.
(b) Install the visor with two screws and the cover.
10. INSTALL SUN VISOR (a) Install the holder with the screw.
(b) Install the sun visor with two screws and the cover.
±
BODY Trim, Assist Grip and VisorBO±125
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
TORQUE SPECIFICATIONS
Part tightenedNVmkgf Vcmft Vlbf
HOOD
Hood support X Hood22225 16
Hood support X Body22225 16
TRANSPORT HOOK
Front Transport Hook
Front transport hook X Body64650 47
Rear Transport Hook
Rear transport hook X Body64650 47
SEAT
Front seat
Power seat regulator X Body37375 27
Seat back assembly X Seat cushion assembly26260 19
Power seat regulator X Seat cushion assembly26260 19
Rear seat
Rear seat back X Body18185 13
SEAT BELT
Front Seat Belt
Front seat outer belt anchor X Body43440 32
Front seat outer belt lower side X Body43440 32
ELR X Body43440 32
Front seat inner belt X Power seat regulator43440 32
Rear Seat Belt
Rear seat outer belt anchor X Body43440 32
ELR X Body43440 32
Rear seat inner belt X Body43440 32
BUMPER
Front Bumper
Front bumper reinforcement X Body13130 9.4
Rear Bumper
Rear bumper reinforcement X Body131309.4
BO±138±
BODY Service Specifications
WhereEverybodyKnowsYourName

8. REMOVE SPEAKER ASSEMBLYDisconnect connectors from speaker assembly and remove
speaker assembly with four bolts.
9. REMOVE SCREW GROMMETS Using a clip remover, remove two grommets.
10. REMOVE SERVICE HOLE COVER Remove the cover by pulling at the edge by hand.
HINT: Do not tear the cover.
11. DISCONNECT WIRE HARNESS FROM DOOR PANEL Using a clip remover, remove the wire harness clamps from
ten position on the door panel.
12. REMOVE DOOR INSIDE PANEL FRAME Remove three bolts and the frame.
13. REMOVE FRONT DOOR BELT MOULDING (a) Remove eight screws and five nuts.
(b) Using a scraper, remove the double±sided tape from the
rear side.
HINT: Tape the scraper tip before use.
±
BODY Front DoorBO±35
WhereEverybodyKnowsYourName