steering LEXUS SC400 1991 Service Manual PDF

PREPARATION
SST (SPECIAL SERVICE TOOLS)
 Illustration Part No. Part Name Note
 


 

09278±54012
 

Drive Shaft Holding Tool
 


Hydraulic pump pulley
 




 



09286±46011
 




Injection Pump
Spline Shaft Puller
 




Hydraulic pump pulley
 




 



09620±30010
 




Steering Gear Box
Replacer Set
 




 




 



(09627±30010)
 




Steering Sector Shaft
Bushing Replacer
 




Oil seal for hydraulic motor
 




 




(09631±00020)
 




(Handle)
 




Oil seal for hydraulic motor
 




 




09631±10030
 




Oil Seal Remover
 




Oil seal for hydraulic pump
 




 




09843±18020
 




Diagnosis Check
Wire 




RECOMMENDED TOOLS 

Illustration
 

Part No.
 

Part Name
 

Note
 




 




09025±00010
 




Small Torque
Wrench 




For measuring preload
 


 

09082±00015 


TOYOTA
Electrical tester 


 




 



09200±00010
 




Engine Adjust
Kit
 




 




 



09258±00030
 



Hose Plug Set
 




Plug for the vacuum hose, oil hose ect.
 




 




09904±00010
 




Expander
Set
 




Oil seal for hydraulic pump
 




 




09905±00013
 




Snap Ring
Pliers
 




Oil seal for hydraulic pump
CO±4±
COOLIING SYSTEM Preparation
WhereEverybodyKnowsYourName

EG24R±02
CYLINDER HEADS REMOVAL
(See Components for Removal and Installation)
1. DISCONNECT TIMING BELT FROM CAMSHAFT TIMING PULLEYS
(See steps 1 to 29 on pages EG±46 to 54)
2. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt and timing pulley. Remove the 2
timing pulleys.
SST 09278±54012
3. REMOVE FAN BRACKET Remove the 2 bolts, 2 nuts and fan bracket.
NOTICE:
w Be careful not to drop anything inside the timing belt
cover.
w Do not allow the belt to come into correct with oil, water
or dust.
4. DISCONNECT POWER STEERING (PS) PUMP FROM
ENGINE
(a) Disconnect the vacuum hose from the air intake chamber.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±75
WhereEverybodyKnowsYourName

(g) Connect the water bypass hose to the IAC valve.
38. INSTALL RH IGNITION COIL
(a) Install the ignition coil with the 2 bolts.
(b) Connect the ignition coil connector.
39. CONNECT CONTROL CABLES TO THROTTLE BODYConnect the following cables:
(1) Accelerator cable
(2) Transmission throttle control cable
(3) Cruise control actuator cable
40. INSTALL THROTTLE BODY COVER
(a) Install the thro ttle body cover and hose clamp with the cap nut
and 2 bolts.
(b) Install the EVAP hose to the hose clamp.
41. INSTALL POWER STEERING (PS) PUMP
(a) Install the PS pump with the nut and 3 bolts. Alternately tighten the bolts and nut.
Torque:
39 NVm (400 kgf Vcm, 29 ft Vlbf) for bolt
43 N Vm (440 kgf Vcm, 32 ft Vlbf) for nut
EG±134±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

15. DISCONNECT ENGINE WIRE CONNECTORS
16. DISCONNECT THEFT DETERRENT HORN CONNECTOR
17. DISCONNECT GROUND CABLE FROM BODY
18. DIS CO NNE CT PO WE R STE E RING (P S ) SO LE NO IDVALVE CONNECTOR
19. DISCONNECT WIRE CLAMP (FOR GENERATOR) FROM VSV (FOR EVAP)
(a) Remove the 2 bolts, and disconnect the VSV from the RH
cylinder head.
(b) Disconnect the wire clamp from the VSV bracket.
20. REMOVE GENERATOR
(a) Disconnect the generator connector.
(b) Remove the cap and nut, and disconnect the generator wire.
(c) Remove the bolt, and disconnect the transmission oil cooler pipe bracket from the generator.
(d) Remove the nut and generator.
21. DISCONNECT POWER STEERING (PS) TUBES FROM SUSPENSION CROSSMEMBER
Remove the clamp bolt, and disconnect the PS tubes.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±143
WhereEverybodyKnowsYourName

22. DISCONNECT POWER STEERING (PS) RESERVOIRTANK AND BRACKET FROM BODY
Remove the 3 bolts, and disconnect the reservoir tank and
bracket assembly.
23. DISCONNECT POWER STEERING (PS) PUMP FROM ENGINE
Remove the nut and 3 bolts, and disconnect the PS pump
from the engine.
HINT: Put aside the PS pump, and suspend it.
24. DISCONNECT AIR CONDITIONING (A/C) COMPRESSOR FROM ENGINE
(a) Disconnect the A/C compressor connector.
(b) Remove the nut, and disconnect the ground cable from the
A/C compressor stay.
(c) Remove the bolt and A/C compressor stay.
(d) Remove the 2 bolts, and disconnect the A/C compressor from the engine.
HINT: Put aside the A/C compressor, and suspend it.
25. DISCONNECT HOSES Disconnect the following hoses and ground strap:
(1) Heater water hose from water bypass hose
(2) Heater water hose from heater water valve
(3) Brake booster hose from union on air intake chamber
(4) Vacuum hose (from VSV for heater water valve) from air
intake chamber
(5) Ground strap from bracket on body.
EG±144
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

15. INSTALL POWER STEERING (PS) PUMP
(a) Install the PS pump with the nut and 3 bolts. Alternatelytighten the bolts and nut.
Torque:
39 NVm (400 kgf Vcm, 29 ft Vlbf) for bolt
43 N Vm (440 kgf Vcm, 32 ft Vlbf) for nut
16. INSTALL POWER STEERING (PS) RESERVOIR TANK
AND BRACKET
Install the reservoir tank and bracket assembly with the 3
bolts.
17. INSTALL POWER STEERING (PS) TUBES Install the PS tube clamp with the bolt.
18. INSTALL GENERATOR
(a) Install the generator and transmission oil cooler pipe bracket with the bolt and nut.
Torque: 37 N Vm (380 kgf Vcm, 27 ft Vlbf)
(b) Connect the generator connector.
(c) Connect the generator wire with the nut and cap.
19. INSTALL WIRE CLAMP (FOR GENERATOR) AND VSV
(FOR EVAP)
(a) Install the wire clamp to the VSV bracket.
(b) Install the VSV with the 2 bolts.
EG±198
±
1UZ±FE ENGINE ENGINE MEHANICAL
WhereEverybodyKnowsYourName

20. INSTALL POWER STEERING (PS) SOLENOID VALVECONNECTOR
21. CONNECT ENGINE WIRE CONNECTORS
22. CONNECT THEFT DETERRENT HORN CONNECTOR
23. INSTALL GROUND CABLE TO BODY
24. CONNECT IGNITER CONNECTORS
(a) Connect the 2 igniter connectors HINT: Connect the yellow taped connector to the igniter on
the rear side.
(b) Install the wire clamp.
25. INSTALL RADIATOR ASSEMBLY
(a) Install the 2 lower radiator supports to the radiator.
(b) Place the radiator assembly on the body bracket.
(c) Slightly lift the radiator, and connect the 2 oil cooler hoses (for
cooling fan) to the hose clamp on the radiator fan shroud.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±199
WhereEverybodyKnowsYourName

(b) Place the matchmarks on the both flanges.
(c) Remove the four bolts, washers, nuts and intermediateshaft.
(d) Insert SST in transmission to prevent oil leakage.
SST 09325±20010 (M/T)
09325±40010 (A/T)
21. REMOVE ENGINE AND T RANSMISSION ASSEMBLY
FROM VEHICLE
(a) Attach the engine hoist chain to the engine hangers.
(b) Remove the two nuts holding the engine to the front suspension crossmember.
(c) Remove the four bolts, four nuts and rear engine mounting member.
(d) Lift the engine out of the vehicle slowly and carefully.
NOTICE: Remove carefully without damaging the power
steering gear housing or the park/neutral position switch
(A/T only).
(e) Make sure the engine is clear of all wiring, hoses and cables.
(f) Place the engine and transmission assembly onto the
stand.
EM±72
±
ENGINE MECHANICAL Cylinder Block
WhereEverybodyKnowsYourName

INSTALLATION OF ENGINE
(See Components on pages EM±62 to 64)
1. INSTALL ENGINE AND TRANSMISSION ASSEMBLY INVEHICLE
(a) Attach the engine hoist chain to the engine hangers.
(b) Lower the engine and transmission assembly into the
engine compartment.
CAUTION: Install carefully without damaging the power
steering gear housing or the park/neutral position switch
(A/T only).
(c) Insert the stud bolts of the front engine m ounting
brackets into the stud bolt holes of the front suspension
crossmember.
(d) Keep the engine level.
(e) Install the rear engine mounting member with the four bolts and four nuts.
Torque: Nut 13 N Vm (135 kgf Vcm, 10 ft Vlbf)
Bolt 25 N Vm (260 kgf Vcm, 19 ft Vlbf)
2. INSTALL INTERMEDIATE SHAFT
(a) Remove SST.
SST 09325±20010 (M/T)
09325±40010 (A/T)
(b) Insert the yoke into the transmission.
(c) Align the matchmarks on the flanges and connect thepropeller shaft with the four bolts, washers and nuts.
(d) Torque the bolts and nuts.
Torque: 74 N Vm (750 kgf Vcm, 54 ft Vlbf)
(e) Torque the bolts.
Torque: 49 N Vm (500 kgf Vcm, 36 ft Vlbf)
EM±104±
ENGINE MECHANICAL Cylinder Block
WhereEverybodyKnowsYourName

Preparation
SST (SPECIAL SERVICE TOOLS)
IllustrationPart No.Part NameNote
09268±41045Injection Measuring
Tool Set
(90268±41070)No. 4 Union
Injector
(09268±41080)No. 6 Union
Cold start Injector
(09268±52010)Injection Measuring
Attachment
Injector
09268±45012EFI Fuel Pressure
Gauge
09612±24014
Steering Gear
Housing Overhaul
Tool Set
(09617±24011)Steering Rack Wrench
Fuel pressure pulsation damper
09631±22020
Power Steering
Hose Nut 14 X 17 mm
Wrench SetFuel line flare nut
09816±30010Oil Pressure
Switch SocketKnock sensor
09842±30055Wire ªGº
EFI Inspection
Cold start Injector
09842±30070Wire ªFº
EFI Inspection
Injector
09843±18020Diagnosis Check
Wire
0990±01000
Engine Control
Computer
Check Harness ªAº
FI±10 ± PreparationEFI SYSTEM
WhereEverybodyKnowsYourName