differential MAZDA 323 1992 Workshop Manual Suplement

. _ .
GI JACK AND SAFETY STAND POSlTiOtWVEHlCLE LIFT (2-SUPPORT TYPE) POSlTlONS
JACK AND SAFETY STAND POSITIONS
FRONT END
JacKposition:
At the front crossmember Safety stand positions:
On both sides of the body frame
REAR END
Jack position:
At the center of the rear crossmember Safety stand positions:
On both sides of the body frame
At the rear differential (4WD)
--
03UGW80
VEHICLE LIFT (2-SUPPORT TYPE) POSITIONS
FRONT END, REAR END
Frame Frame
Side sills Side sills
9MuGIX 010 9MVGtX 01

GI MAINTENANCE NOTE
VIEWED
.OM BELOW
‘REE
13EGfX-307
I
I t3EGIX-308 CHASSIS DYNAMOMETER CHECK
Caution
l Do not clutch abruptly. l Do not attempt rabbit starts or accelerate quickly.
1. Remove the propeller shaft.
2. Lock the center differential (2WD).
3. Place the front wheets on the roller.
4. Lock the rear wheels and apply the parking brake.
5. Drive the tester roller and check.
6. Upon completion of the test, gradually decelerate with soft
braking and stop the engine.
7. When the test is done, return the differential lclck rod to the
free condition (4WD) and reinstall the propeller shaft.
WHEEL BALANCER (On-the-car Balance)
1.
Jack up all four wheels. Support the wheels to be checked
(front or rear) with the wheel balancer sensor stand and the
remainrng wheels with safety stands.
2. Set the on-the-car balancer. With the center differential in
free condition, drove the tires with the engine; then check.

OUTLINE M
OUTttNE
OUTLiNE OF CONSTRUCTION
l TKe construction and operation of the front and rear axles are basically the same as previous models.
l Because of the use of a high power engine, the following parts are modified to improve rigidity.
(I) Larger front and rear bearings are used.
(2) Larger front and rear knuckles are used.
(3) A five-stud wheel hub is used.
l An ice scraper is newly installed on the rear knuckle to prevent ice from building up on the brake caliper.
(Refer to page M-14.)
13EOMX-303
SPECIWCATIONS
Hem Speclficatlons
Front driveshaft
Joint type inside
Double offset joint
Outsrde Bell joint
Length of joint (between center of joint) Right
392 I15.4)
mm lrn)
Left 306 IO.831
Shaft drameter mm fin)
21.0 (0.83)
Rear driveshaft
Inside
Joint type Double offset joint
Outside 5ell joint
Length of joint (between center of joint) Right
519.5 [ 20.5 1
mm [in]
Left.
489.5 ( 19.3 )
Shaft diameter mm (in) 21.0 [O&3]
Joint shaft
I
Length of joint
Shaft diameter
Front axle
mm jin] 357.2 114.11
mm {in] 21.0 {0.83]
4
Bearing play axial direction mm tin)
0.05 IO.002 ]
I
Rear axle
Bearing play axial direction mm (inj
Rear dtfferentlal (viscous limited slip differential) 0.05 (0.002 1
Reduction aear Hypoid gear
Differentral gear
Drfferential ratio Straight bevel gear
3.909
Number of teeth Ring gear .
Drive binion aear
43
If
Fluid I Grade API Service GL-5
Above -t8*C (O*F) SAE 90
Viscosity .
Below -18*C i O*Fl SAE 8OW
1 I Capacity L I US qt, imp stl 1 0.65 !O.SS, 0.571
1
13EOMX-304
M-3

TD TECHNICAL DATA
LU8RlCATtON SYSTEM
Item
Lubricating method
011 pump Engine
BP DOHC turbo
Force-fed
6 . Trochoid gear
Relief pressure
kPa I kgf/cm’. psi] 343-441 [ 3.5-4.5, 50-64 1
Regulated pressure kPa { kgf/cm’ , psi ] -rpm
294-392 { 3.0-4.0, 43--57.1.3,000
Inner rotor tooth tip to outer. rotor Standard
0.02-0.16 (OJOOS-O.O063]
clearance
mm {in]
Maximum I
0.20 [ 0.0078 )
Outer rotor to body clearance
Side clearance
Oil fIl!er
, TYpe
Relief pressure differential . mm [in) Standard
Maximum
mm {in) Standard
Maximum 1
kPa’ f kgf/cm’, psi 1 0.09-0.18 ~0.00354.Ofl71]
0.22 { 0.0087 1
0.03-0.11 ~0.0012-0.0043~
0.14 {0.0055)
Full-flow, paper element
. 78-118 (0.8-1.2. 11-17) Srade
----l-in
Viscosity
num her
Item
Cooling metha
Water pump
, We
Impeller diame
Number of imf
Speed ratio -
Water seal !$
Thermostat
Jype. _
Opening terq
/Full-open
1 F&open lift
I
Antifreeze E
TD-4

TECHNICAL DATA TD
Item
t-2 slmfl fork and reverse gear Standard 0.1 O-O.45 [ 0.004-0.018 1
mm {in] Wear limit
I 0.95 (0.037 ]
3-4 shift fork and ctutch hub sleeve Standard 0.10-0.40 [0.004-O.OlS]
mm [In]
Wear limit
I 0.90 (0.035 ]
5th shift fork and clutch hub sleeve Standard 0.10-0.36 {0.004-0.014]
mm [in]
Wear limit
I 0.86 [ 0.034 1
Reverse idle gear and reverse lever Standard 0.10-0.35 ~0.004-0.014 )
mm fin)
Wear limit
I 0.85 tO.033)
Standard o-0.05 [ 0-0.002 ]
Primary shaft gear mm [in ] 0.20 lO.OOS], 0.25 [O.OlO), 0.30 (0.012], 0.35 (0.014),
Adjustment shims 0.40 lO.OlS], 0.45 [O.OlS), 0.50 (0.020], 0.55 [0.022],
0.60 fO.0241. 0.65 f0.0261. 0.70 fO.0281
Standard t 0.03-0.08 { 0.001-0.003 1
Secondary shaft gear mm [in] 0.20 tO.O08], 0.25 {O.OlO], 0.30 (0.012], 0.35 [0.014),
Adjustment shims 0.40 (O.Ot6], 0.45 (0.018], 0.50 [0.020], 0.55 10.022),
0.60 IO.0241, 0.65 {0.026], 0.70 [0.028]
Center differential
Me Planetary carrier
Number of ring gear teeth
Number of pinion gear teeth Outer
Inner
Outer
Inner 59
75
14
! 14
Number of sun gear teeth
Number of idle-gear teeth
Bearing preload Pinion gear side
I 43
Idle gear side 43
37
N.m { kgfcm. inlbf 1 3.0-3.9 f30-40, 27-34 )
0.25 {O.OtOl, 0.30 {0.012],
CI---.-- ---I--A --I: _d---* -L!- aeanng pretoaa aqusrmenr snrm mm [in] 0.10
0.35
0.55
0.75
0.95
1.15 0.004 ], 0.20
0.014), 0.40
0.022 ) , 0.60
0.030 ) , 0.80
0.0371, 1.00
0.0451. 1.20 0.008
0.016
0.024
0.031
0.039
0.047 -
: 0.45 lO.O18], 0.50 !0.020],
: 0.65 0.85 (0.026] [0.033], p 0.70 0.90 [ { 0.028 0.035], 1,
I 1.05 (0.041], 1.10 [P.O43], r
End play of ring gear mm {in) 0.1510.36 i 0.006-0.012 ]
Ring gear end play adjustment washer mm {in) 1.20 40.047], 1.35 t0.053], 1.50 [0.059),
1.65 {0.065], 1.80 iO.071 1
End play of sun gear mm (in]
0.100-0.300 [ 0.0039-0.0118 ]
-
Sun gear adjustment washer mm {in] 3.5 lO.lSS], 3.7 (0.146). 3.9 (0.154].
4.1 IO.161 1, 4.3 [O.lSS]
Transfer Cattier
Final gear reduction ratio 4.214
Number of teeth
Oil Ring gear -
Pinion gear
Type
Capacity
L I US qt, Imp q?] . 37
11
API: GL-5
Above -18% lOoF]: SAE 90
Below -18OC {OOF]: SAE 8OW
0.5 [0.53. 0.44)

TD TECHNICAL DATA
Hem Engine
SP DOHC turbo
Note ) I
1 st and 2nd
Synchronizer ring outer diameter
’ I 67.7 I2.665)
mm [in] 3rd and 4th 67.7 12.665 )
5th and reverse 55.7 t2.192)
Synchronizer key dimension 1st and 2nd @ 19.0 {0.748], 04.3 (0.171, 05.0 10.20)
mm [in] 3rd and 4th @ 17.0 10.669J, 04.3 (0.171, @ 5.0 lO.20)
5th and reverse 0 17.0 10.6691, m4.3
10.171, @I 5.0 fO.201
PROPELLER SHAFT
Item
length
Outer diameter Engineflransaxie Model BP DOHC turbo
G25MX-R (GSMX-R)
Front 834.3 { 32.85 ]
mm fin] Center 584 122.99)
Rear
I 437 { 17.20)
Front 75 (2.95)
mm { in] Center 57 12.24) f
Rear 57 12.241
FRONT AND REAR AXLES
Item Specifications
Front driveshaft

Jomt type Inside Double oftset joint
Outside Bell jotnt
Length of joint (between center of joint) mm { rn t - Right 392 (15.4)
left 306 (0.83 ]
Shaft diameter mm {in] 21.0 to.831
I
Rear driveshaft
Joint type Inside 1
Outside 1
Length of joint (between center of joint) mm [in ] ’ Right
Left
Shaft diameter mm (in)
J&t shatt
Length of joint
Shaft diameter
Front axle
Bearing play axial direction mm [in] 1
Rear axle
Bearing play axial direction mm lin] 1
Rear differential (viscous limited slip differential) Double offset joint
Bell joint
519.5 (20.5 ]
489.5 [f9.3]
21.0 IO.831
357.2 1 t4.11
21 .O (0.83 )
0.050 IO.002 ]
0.050 (0.002 ]
*
Reduction gear
Different ia gear
Oifferential ratro
Number of teeth
Flurd
L Ring gear
Drive .pinion gear
Grade
Viscosity Above -18*C fO*F ]
Below -18*C lOoF)
, Capacity
L fUS qt, Imp c$l Hypoid gear
Straight bevel gear
3.909
43
11
API Service GL-5
SAE 90
SAE 80W
0.65 lQ.69, 0.571 STEERING SI
1 Free olav 8RAKING SY
Brake type
Brake pedat
Height
Free play 1
Reserve travel
Clearance whet
Master cylinde
Master cylinder
Front disc brai
. Tyl?e
Thickness of p&
Thickness of pa