R–18
REAR SUSPENSION
Crossmember component, Differential And Drive Shaft Removal Note
1. Support the differential with a jack, and remove
the nut.
Warning
•Removing the crossmember component,
differential and drive shaft is dangerous.
The crossmember component,
differential and drive shaft could fall and
cause serious injury or death. Verify that
the jack securely supports the differential
lower side.
2. Remove the crossmember component,
differential and drive shaft.
Rear Crossmember Bushing Removal Note
1. Remove the bushing using a screw driver (-),
being careful not to damage the rear
crossmember.
Rear Crossmember Bushing Installation Note
1. Set the bushings as shown in the figure.
JACK
A6E74162012
A6E7416W001
A
B
D
C
A
B
C,D
FRONT
UPPER SIDELOWER SIDE
OVAL
HOLECROSS-
SECTIONAL
VIEW
A6E74162014
TD–6
TECHNICAL DATA
FRONT AND REAR AXLEA6E931001018201
End Of Sie
STEERING SYSTEMA6E931001034201
End Of Sie
Item Specification
FRONT DRIVE SHAFT
Shaft length
(Air in boot at atmospheric
pressure)(mm {in})Left sideMZR-CD (RF Turbo): 666.1—676.1 {26.23—26.61}
4WD: 667—677 {26.26—26.65}
Right sideMZR-CD (RF Turbo): 615.9—625.9 {24.25—24.64}
4WD: 631—641 {24.85—25.23}
REAR DRIVE SHAFT (4WD)
Shaft length
(Air in boot at atmospheric
pressure)(mm {in})Left side 805.4—815.4 {31.71—32.10}
Right side 852.4—862.4 {33.56—33.95}
REAR DIFFERENTIAL (4WD)
Pinion height (mm {in})–0.025—0.025 {–0.001—0.001}
Backlash of side gear and differential pinion (mm {in}) 0.1 {0.004} or less
Drive pinion preload (N·m kgf·cm, in·lbf) 1.3—1.8 {13.3—18.3, 11.5—15.9}
Backlash of drive pinion and
ring gear(mm {in})Standard 0.09—0.11 {0.0036—0.0043}
Minimum 0.05 {0.002}
Differential oilGrade API service GL-5
ViscosityAbove –18°C {0°F}: SAE 90
Below –18°C {0°F}: SAE 80
Capacity
(Approximate quantity)(L {US qt, lmp qt}) 1.00 {1.06, 0.88}
ELECTRONIC 4WD CONTROL SYSTEM
Differential oil temperature
sensor(kilohm)0°C {32°F} 91—100
10°C {50°F} 56—61
20°C {68°F} 35—39
30°C {86°F} 23—25
40°C {104°F} 14—17
50°C {122°F} 10—11
60°C {140°F} 7.1—7.9
70°C {158°F} 5.0—5.6
80°C {176°F} 3.6—4.0
4WD solenoid
(Rear differential oil temperature
at 20°C {68°F})(ohm) 1.5—2.0
Item Specification
ENGINE SPEED SENSING POWER STEERING
Power
steering oil
pumpOil pump fluid pressure 2WD (Except MZR-CD (RF Turbo)):
10.80—11.29 {110.2—115.1, 1,567—1,637}
MZR-CD (RF Turbo):
11.31—11.80 {115.4—120.3, 1,641—1,711}
4WD: 10.30—10.79 {105.1—110.0, 1,490—1,564} (MPa {kgf·cm
2, psi})
Gear housing fluid pressure 2WD (Except MZR-CD (RF Turbo)):
10.80—11.29 {110.2—115.1, 1,567—1,637}
MZR-CD (RF Turbo):
11.31—11.80 {115.4—120.3, 1,641—1,711}
4WD: 10.30—10.79 {105.1—110.0, 1,490—1,564} (MPa {kgf·cm
2, psi})
Power
steering
systemFluid type
ATF M-
III or equivalent (e.g. Dexron®II)
Capacity (Approximate quantity) MTX (Except MZR-CD (RF Turbo)): 0.80 {0.85, 0.70}
ATX (Except 4WD): 0.87 {0.92, 0.77}
MZR-CD (RF Turbo): 0.86 {0.91, 0.76}
4WD: 0.89 {0.94, 0.78} (L {US qt, Imp qt})
