check engine MAZDA 626 1987 Owners Manual

PCV SYSTEM 4A
POSITIVE CRANKCASE VENTILATION
(PCV)
SYSTEM
Air cleaner pcv valve
76G04A-131
This system reburns the blow-by gases and operates while the engine is running to reduce emissions.
PCV VALVE
Inspection
1. Warm up the engine to the normal operating tem-
perature and run it at idle.
2. Disconnect the PCV valve and the ventilation hose
from the cylinder head cover.
3. Block the PCV valve and check that the engine
speed drops.
4. Replace the PCV valve if necessary.
76G04A-132
4A—67

IDLE-UP CONTROL SYSTEM 4 A
FE (Middle East) and F6 (General)
Possible cause
jrvo

diaphragm

3
jrvo

diaphragm

n c o> (0
E 3 3 O
® >
a >
•o o c e
£ O **
S M O
£ O
'i (0 (0
O <
o a
o E W 0)
lm Q.
c a k 4) -
9-5
"S "5 (O > CO < a. DC H Js * OC M
Page 4A—72 4A—74 4A—74 Section 15 4A—75 Section 16
Checking order 1 2 3 4 5 6 7 8
76G04A-136
FE 8Valve—Unleaded Fuel
Posible cause

Engine

control

unit

terminal

Servo

diaphragm

Vacuum

signal

Solenoid

valve £ O **
S CO O
£ U
S <0 U) Relay
(for
A/C) ** n ** w o E «
Refrigerant
pressure

switch
H D I Servo

diaphragm

Vacuum

signal

Solenoid

valve
< a. Relay
(for
A/C)
H Refrigerant
pressure

switch

Page 4A—91 4A—72 4A—74 4A—74 Section 15 4A—75 Section 16
Checking order 9 1 2 3 4 5 6 7 8
76G04A-137
4A—71

4A IDLE-UP CONTROL SYSTEM
Servo Diaphragm
Dual servo diaphragm type
1. Warm up the engine and run it at idle.
2. Connect a tachometer to the engine.
3. Disconnect the vacuum hose from the servo di-
aphragm port A.
4. Apply intake manifold vacuum directly to the di-
aphragm.
Caution
All accessories must be OFF.
76G04A-138
5. Check that the engine speed is within the specifi-
cation.
Engine speed: 1,200—1,400 rpm
6. If not within specification, turn the adjust screw to
adjust.
7. Reconnect the vacuum hoses.
76G04A-139
8. Disconnect the solenoid valve vacuum hose from
the servo diaphragm port B.
9. Apply intake manifold vacuum directly to the di-
aphragm.
10. Check that the engine speed is within specification.
Engine speed: 800—1,000 rpm (MTX)
1,050—1,250 rpm (ATX)
(in N range)
76G04A-140
Adjust screw
11. If not within specification, turn the adjust screw to
adjust.
12. Reconnect the vacuum hoses.
76G04A-141
4A—72

IDLE-UP CONTROL SYSTEM 4A
Single servo diaphragm type
1. Warm up the engine and run it at idle.
2. Connect a tachometer to the engine.
3. Disconnect the vacuum hose from the servo di-
aphragm.
4. Check that the engine speed is within specification.
Engine speed:
P/S operated 800—1,000 rpm (MTX) P/S operated 1,050—1,250 rpm (ATX) (in N range)
A/C operated 1,200—1,400 rpm
76G04A-142
6. If not within specification, turn the adjust screw to
adjust.
76G04A-143
4A-73

4A IDLE-UP CONTROL SYSTEM
76G04A-144
76G04A-145
76G04A-146
Vacuum Signal [Equipped with A/C, only FE and
F8 (Except Middle East and General)]
1. Start the engine and run it at idle.
2. Disconnect the vacuum hose from the servo di-
aphragm.
3. Place a finger over the hose.
4. Increase the engine speed, and check for vacuum.
Engine model Engine speed Vacuum
pj| (Except Middle) Below 2,300 rpm Yes pj| (Except Middle) Above 2,300 rpm No
FE (Unleaded fuel) Below 1,500 rpm Yes FE (Unleaded fuel) Above 1,500 rpm No
F6 (Singapore) Below 2,100 rpm Yes F6 (Singapore) Above 2,100 rpm No
General and Middle East
1. Start the engine and run it at idle.
2. Disconnect the vacuum hose from the servo di-
aphragm.
3. Place a finger over the hose.
4. Operate the A/C or P/S.
5. Check that vacuum is felt.
P/S Switch
1. Start the engine and run it at idle.
2. Disconnect the power steering switch connector.
3. Connect an ohmmeter to the power steering
switch.
4. Turn the steering wheel all the way to either the
right or left, and check for continuity.
P/S Continuity
Operated Yes
Not operated No
5. Replace if necessary.
Solenoid Valve (A/C)
1. Disconnect vacuum hose A from the servo di-
aphragm.
2. Disconnect vacuum hose B from the solenoid
valve.
3. Disconnect the solenoid valve connector.
4. Blow air through the valve from hose A and check
that it comes out of port C.
76G04A-147
4A-74

IDLE-UP CONTROL SYSTEM 4A
Troubleshooting
Note
Make the system inspection first. If no problem is found, continue with the next inspec-
tion of the Troubleshooting. (Refer to page 4A—70.)
\\ Possible cause
\ Page
£ O
S in c o
£ O **
in
0) ** (0 o
o **
s <0
o ** c o o •o d>
£ O **
S (0 o E a>
X 1-<,
£ O
S w £ O
a> > a >
u o c 0) o
c 3
O ** C o
c o s o a> a (0 c
c a E o o
® TJ w <0 4> DC
0) a » c cs IL
a> (0
o
£ C
i « a <
a. 3 a>

Engine

i
terminal
E a>
s. CO
Symptom
Section
15 Section 15 4A—95 4A—93 Section
15 4A—77 4A—86— 4A—91 4A—77
Checking order 3 4 5 6 7 8 2 9 1
76G04A-152
'Engine control unit terminal Check the following terminal voltages
Transmission Terminal
MTX A, C, D, H, Q, R
ATX I, 2B, 2C, 2D, 2E, 2H, 2M
System Inspection
1. Warm up the engine and run it at idle.
2. Connect a jumper wire to the carburetor connec-
tor terminal wire (YW) and ground.
3. Connect a tachometer to the engine.
4. Turn all accessories off.
5. Verify that the engine speed is within specification.
Engine speed: 900—950 rpm (MTX)
Engine speed: 1,000—1,050 rpm
(ATX; in N range)
6. Disconnect the tachometer.
76G04A-153
Idle-up Solenoid Valve
1. Turn all accessories OFF and turn the ignition
switch ON.
2. Disconnect the idle-up solenoid valve connector.
3. Ground the carburetor connector terminal wire
(YW) using with a jumper wire.
4. Check the rod is drawn into the valve.
5. Replace if necessary.
U
76G04A-154
4A-77

IGNITION TIMING CONTROL SYSTEM 4A
TROUBLESHOOTING
Check the condition of the wiring harness and components before checking the sensors or switches.
\\ Possible cause , . Engine control unit terminal
\ Page

rater

thermo

switch

itake

manifold)

'ater

thermo

switch

Iadiator)
hibitor

switch

Solenoid

valve

(Ignition

timing

contra

0) >
5 >> n
acuum

control

unit

Ustributor)
Symptom \J

•S-
o 5 t c
Solenoid

valve

(Ignition

timing

contra

O > B 1F 2A 2F 2H 2M Symptom \J 4A—95 4A—95 4A—93 4A—81 4A—82 Section 5 4A—85 4A--86
Poor accelera-
tion, hesitation, 5 6 4 2 3 1 11 7 8 9 10 or lack of power
Fails emission test 4 5 3 2 — 1 10 6 7 8 9
76G04A-161
Solenoid Valve (Ignition Timing Control)
1. Disconnect the vacuum hose from the solenoid
valve and vacuum pipe.
2. Blow through the solenoid valve from vacuum hose
A.
3. Check that air flows from port B.
76G04A-162
4. Disconnect the solenoid valve connector.
5. Connect 12V and a ground to the terminals of the
solenoid valve.
6. Blow through the solenoid valve from vacuum hose
A.
7. Check that air flows from the valve air filter.
76G04A-163
4 A—81

4A CONTROL SYSTEM
ENGINE CONTROL UNIT
Check the engine control unit terminal voltages with
a voltmeter.
Caution
a) Warm up the engine before checking the
control unit.
b) If the proper voltage is not obtained, check
the wiring, connections and finally, check
the component.
FE and F8 Engine — ATX (ECE, Hong Kong, and Singapore)
Terminal
(Wire color) Connected to Condition Voltage

1A
(BW)
Ignition switch Ignition switch ON. Battery voltage

m
ST
'-O
Solenoid valve (Main
air
bleed control) Others Battery voltage
m
ST
'-O
Solenoid valve (Main
air
bleed control) Radiator coolant temperature below 17°C (63°F)
or
intake manifold vacuum more than 200 mmHg (7.9 inHg)
Below 1,5V
1C (GO) Solenoid valve (Choke opener) Radiator coolant temperature below 17°C (63°F)
or
during cranking and
27
sec. after engine starts Below 1,5V
Others Battery voltage
1D
(GL)
Air bypass solenoid valve Idle switch OFF and engine speed above approx. 2,100 rpm Below 1,5V
Others Battery voltage
1E
— — —

1F
(G) Solenoid valve (Ignition timing control system)
Radiator coolant temperature above 17°C (63°F),
en-
gine coolant temperature below 72°C (162°F), inhibi-tor switch OFF and engine speed below 2,300
rpm

Below 1.5 V
Others Battery voltage
1G
— — —

1H
(LW) Solenoid valve (A/C) A/C switch
ON
and engine speed below approx. 2,300
rpm

Below 1,5V
Others Battery voltage
11
(YW) Idle-up solenoid valve Inhibitor switch OFF and, headlight switch ON, rear
defroster switch ON, fan speed control switch
is 3rd

or 4th position, A/C operated,
or
engine coolant tem-
perature below 72°C (162°F)
Below 1,5V
Others Battery voltage
1J
(B)
Ground
—
Below 1,5V

9 MSSirSl
ivj
A 1
k *
76G04A-169
4A—86

CONTROL SYSTEM 4 A
76G04A-176
76G04A-177
76G04A-178
Replacement
1. Disconnect the negative battery cable.
2. Remove the front console covers (right or left).
3. Disconnect the connectors from the control unit.
4. Remove and replace the control unit.
INHIBITOR SWITCH
Inspection
1. Verify that the starter operates with the ignition
switch at START position in
P
and N positions only.
2. Check that the back-up lights illuminate when R
position selected and the ignition switch is ON.
3. If not as specified, check the following:
(1) Jack up the vehicle and support it with safety
stands.
(2) Disconnect the inhibitor switch connector.
(3) Check continuity of the switch with an
ohmmeter.
Connecting guide

Position

N

D,1,2
Connector terminal

O -O
O
O
-O
-O

O—O: indicates continuity

4. Replace if necessary.
IDLE SWITCH
Inspection
1. Warm up the engine and run it at idle.
2. Turn all accessories OFF.
3. Connect a tachometer to the engine.
4. Connect a voltmeter to the carburetor connector
F terminal.
76G04A-179
4A-93

4A CONTROL SYSTEM
Idle switch
Adjust screw
76G04A-180
76G04A-181
5. Increase the engine speed to more than 2,000 rpm
and decelerate gradually.
6. Check the voltage.

Specification
Engine speed
^^^

FE 8Valve—
Unleaded Fuel
& F6 Sin-
gapore
Others
At idle below 1,5V Battery voltage
Above 1,000—1,100 rpm Battery voltage below 1.5V

7. If the voltage is not within specification, turn the ad-
just screw to adjust.
VACUUM SWITCH
On-Vehicle Inspection
1. Run the engine at idle.
2. Connect a voltmeter to the vacuum switch connec-
tor terminal wire (LB).
Voltage: Approx. 12V
3. Disconnect the vacuum hose from the vacuum
switch, and plug it.
4. Check the voltage.
Voltage: Less than 1.5V
Off-Vehicle Inspection
Inspection
1. Remove the vacuum switch.
2. Connect a vacuum pump to the vacuum switch.
3. Connect an ohmmeterto the vacuum switch, and
check the continuity between the switch terminals.

Vacuum Continuity
MTX: More than 300 mmHg (11.8 inHg) No ATX: More than 200 mmHg (7.9 inHg) No
Others Yes

76G04A-182
4A—94