Rear brakes MAZDA 626 1987 User Guide

REAR DRUM BRAKE 1 1
5. Fit of drum and lining
(1) Apply chalk to the inside of the drum.
(2) Rub the shoe against the drum.
(3) Check lining to drum contact.
(4) After checking, remove chalk.
2. Tighten all nuts and bolts to the specified torque, referring to torque specifications.
3. After installation:
(1) Add brake fluid and bleed air. (Refer to page 11—9.)
(2) Adjust the parking brake lever stroke. (Refer page to 11—65.)
(3) Depress the brake pedal a few times and check that the rear brakes do not drag while the wheels
are being rotated.
Torque specification
86U11X-120
INSTALLATION
1. Install in the reverse order of removal.
76G11X-050
11—61

1 1 REAR DRUM BRAKE
Brake drum
1. Move the quadrant against the backing plate with
a screwdriver and increase the shoe clearance.
2. Install the brake drum.
Note
The shoe clearance will be automatically ad-
justed by applying the parking brakes.
76G11X089
Locknut
Tighten the new locknut to the specified torque and
securely stake it to the spindle groove.
Tightening torque:
98—177
N
m (10—18 m-kg, 72—130 ft-lb)
Caution
Do not use a pointed tool for staking.
86U11X-129
11-64

PARKING BRAKE 1 1
86U11X-130
86U11X-131
PARKING BRAKE
ON-VEHICLE MAINTENANCE
Parking Brake Lever Stroke
Inspection
Check that the stroke is within specification when the
parking brake lever is pulled with a force of 98N
(10kg, 22lb).
Stroke: 5—7 notches
Adjustment
1. Before adjustment, start the engine and depress
the brake pedal several times.
2. Stop the engine.
3. Remove the adjust nut clip and turn the adjust nut
at the front of the parking cable.
4. After adjustment, check the following points:
(1) Turn the ignition switch ON, pull the parking
brake lever one notch, and check that the park-
ing brake warning lamp illuminates.
(2) Check that the rear brakes do not drag.
11—65

1 1 PARKING BRAKE
REMOVAL AND INSTALLATION OF PARKING BRAKE LEVER
1. Block the wheels firmly.
2. Release the parking brakes.
3. Remove in the sequence shown in the figure.
4. Inspect all parts, referring to inspection note.
5. Install in the reverse order of removal, referring to installation note for specially marked parts.
6. After installation:
Adjust the parking lever stroke. (Refer to page 11—65.)
(1.8—2.5 m-kg, 13-18 ft-lb)
76G11X-051
1. Rear console 4. Adjust nut 7. Button
2. Parking brake switch 5. Parking brake lever 8. Spring
3. Clip 6. Cover
11-66

PARKING BRAKE 1 1
INSTALLATION OF PARKING BRAKE CABLE
1. Install in the reverse order of removal, referring to installation note for specially marked parts.
2. Tighten all nuts and bolts to the specified torque, referring to torque specifications.
3. After installation:
(1) Adjust the parking brake lever stroke. (Refer to page 11—65.)
(2) Depress the brake pedal a few times and check that the rear brakes do not drag while the wheels
are being rotated.
Torque specifications
Rear drum brake
76G11X-053
11-69

ANTI-LOCK BRAKE SYSTEM (ABS) 1 1
86U11X-196
1. Coupler
2. Brake pipe (from master cylinder)
3. Brake pipe (to front brakes)
4. Brake pipe (to rear brakes)
5. Mount bushing
6. Hydraulic unit
11—97