fuel pump MAZDA 626 1987 Manual PDF

FUEL SYSTEM 4C
FUEL TANK
Removal
Caution
a) Before performing the following procedure, release the fuel pressure from the fuel sys-
tem to reduce the possibility of injury or fire. (Refer to page 4C—52.)
b)When removing the fuel tank, keep sparks, cigarettes, and open flames away from the
fuel tank.
Remove in the sequence shown in the figure.
76G04C-125
Note
Drain the fuel from the fuel tank before removing the tank.
1. Remove fuel filler cap.
2. Fuel pump connectors
3. Fuel hoses
4. Steering angle transfer shaft (4-wheel
steering)
(Refer to section 10)
5. Cross member (4-wheel steering)
6. Evaporative hoses
7. Fuel filler hose
8. Breather hose
9. Parking cable bracket
10. Fuel tank strap
11. Fuel tank
4C-65

EGR SYSTEM (UNLEADED FUEL) 4C
Apply 12V
J* Port
76G04C-147
86U04A-133
76G04C-148
4. Disconnect the solenoid valve connector.
5. Connect 12V and a ground to the terminals of the
solenoid valve.
6. Blow through the solenoid valve from vacuum hose
A.
7. Check that air flows from the air filter.
EGR Modulator Valve
1. Remove the EGR modulator valve.
2. Plug the No. 1 port and connect a vacuum pump
to the No. 3 port.
3. Blow into the exhaust gas port. Operate the vacu-
um pump and verify that vacuum is held.
4. Release the exhaust gas port and confirm that
vacuum is released.
EGR Control Valve
1. Warm up the engine and run at idle.
2. Disconnect the vacuum hose from the EGR con-
trol valve and plug it.
3. Verify that the engine runs smoothly.
4. If not correct, clean the exhaust gas passage in
the valve or replace the valve.
Note
Before replacing the EGR control valve, check
the intake air and control systems.
5. Connect a vacuum pump to the valve and apply
vacuum.
6. Verify that the engine runs roughly or stalls at more
than the specified vacuum.
Specification:
40—60 mmHg (1.6—2.4 inHg)
7. If not correct, replace the EGR control valve.
76G04C-149
4C-79

4C CONTROL SYSTEM
RELATIONSHIP CHART
Output Devices
and
Input Devices (Unleaded fuel)
IGNITION SWITCH
(ON POSION) X X X X X O X X X X X X X X O
TEST CONNECTOR X X X O X X X X X X X X X O X
ELECTRICAL LOAD CONTROL UNIT X X X o X X X X X X X X X X X
P/S PRESSURE SWITCH X X X o X X X X X X X X X X X
A/C SWITCH X X X o X X X X X X X X O X X
IGNITION SWITCH
(STA POSITION) O O X o O X X X X O X X X O X
NEUTRAL
AND

CLUTCH SWITCH O X X o X X X X X X X X X X X
OXYGEN SENSOR o X X X X X X X X X X X X X X
WATER THERMO
SWITCH (RADIATOR) o X X X X X X X o X X X X X X
INTAKE
AIR

THERMO SENSOR X X X X X X X X X O X X X X X
WATER
THERMO SENSOR o X X o X X o o O O X X X O o
IDLE SWITCH o X X o X X X X X o X X X O X
THROTTLE SENSOR o X X X X X X X O X X X X o X
AIR FLOW SENSOR o X X X X X X o X X X X X o O
Ne SIGNAL o o X O o X X O O O o o X o O
G SIGNAL X O X X X X X X X X X X X X X

\
INPUT

DEVICE
OUTPUT
DEVICE
FUEL
INJECTION
AMOUNT FUEL

INJECTION

TIMING
AIR
VALVE

ISC
VALVE
FUEL
PUMP

CONTROL
MAIN
POWER
CONTROL
SOLENOID
VALVE
(No.1
PURGE)
SOLENOID
VALVE
(No.2
PURGE)
SOLENOID
VALVE
(EGR)
SOLENOID

VALVE

(PRESSURE

REGULATOR
CONTROL)
SOLENOID
VALVE

(VARIABLE

INERTIA
CONTROL)

OXYGEN

SENSOR
RELAY
I A/C

RELAY

IGNITER
AIR

FLOW
SENSOR
(BURN-OFF)
\
INPUT

DEVICE
OUTPUT
DEVICE
INJECTOR
BAC
VALVE

CONTROL
RELAY
SOLENOID
VALVE
(No.1
PURGE)
SOLENOID
VALVE
(No.2
PURGE)
SOLENOID
VALVE
(EGR)
SOLENOID

VALVE

(PRESSURE

REGULATOR
CONTROL)
SOLENOID
VALVE

(VARIABLE

INERTIA
CONTROL)

OXYGEN

SENSOR
RELAY
I A/C

RELAY

IGNITER
AIR

FLOW
SENSOR
(BURN-OFF)

76G04C-167
4C—92

CONTROL SYSTEM 4C
Output Devices and In put Devices (Leaded fuel)
IGNITION SWITCH
(ON POSITION) X X X X X O X X X X O
TEST CONNECTOR X X X O X X X X X O X
KNOCK SENSOR X X X X X X X X X o X
ELECTRICAL LOAD
CONTROL UNIT X X X O X X X X X X X
P/S PRESSURE SWITCH X X X o X X X X X X X
A/C SWITCH X X X o X X X X O X X
IGNITION SWITCH (STA POSITION) O O X o O X O X X O X
NEUTRAL AND
CLUTCH SWITCH O X X o X X X X X X X
INTAKE AIR THERMO SENSOR X X X X X X O X X X X
WATER THERMO SENSOR O X X o X X O X X O o
IDLE SWITCH o X X o X X o X X O X
VARIABLE RESISTOR (IN AIR FLOW SENSOR) o X X X X X X X X X X
AIR FLOW SENSOR o X X X X X X X X O O
Ne SIGNAL o o X O o X O o X o O
G SIGNAL X O X X X X X X X X X

INPUT

DEVICE

OUTPUT

DEVICE

FUEL

INJECTION

AMOUNT
FUEL

INJECTION

TIMING
AIR
VALVE
ISC

VALVE

FUEL

PUMP

CONTROL
MAIN

POWER

CONTROL

SOLENOID

VALVE

(PRESSURE

REGULATOR

CONTROL)

SOLENOID

VALVE

(VARIABLE

INERTIA

CONTROL)

A/C
RELAY

IGNITER
AIR

FLOW

SENSOR

(BURN-OFF)

INPUT

DEVICE

OUTPUT

DEVICE

INJECTOR
BAC

VALVE

CONTROL
RELAY
SOLENOID

VALVE

(PRESSURE

REGULATOR

CONTROL)

SOLENOID

VALVE

(VARIABLE

INERTIA

CONTROL)

A/C
RELAY

IGNITER
AIR

FLOW

SENSOR

(BURN-OFF)

76G04C-168
4C—93

4C CONTROL SYSTEM
Output Devices
and
Engine Conditions (Unleaded fuel)

REMARK

*
Above

7,000

rpm:

fuel

cut

'Coolant

temp.:
below

50°C

(122°F)

41 Coolant
temp:

below

70°C

(158°F)

*2 Engine
speed
above
1,700
rpm
*3 Engine

speed:

1,500—3,500

rpm

*
During
hot

start

only

*
Engine
speed:
above

5,200

rpm

'Engine

speed:
above

3,000

rpm

'Delays

0.5
second

IGN:

ON

(ENGINE
NOT RUNNING)

No

injection

No bypass OFF
(main

fuel

pump

not
operated)
OFF
OFF
z
1

IDLE

(THROTTLE
VALVE
FULLY CLOSED)
Rich

and

i
lean
Sequential
(once

per

two

revolutions)
OFF

o en C3 UJ
z
"After

start-
ing:

ON

(Vacuum

cut) OFF
o

DECELE-
RATION
'Fuel

cut

L

Small
amount
of
bypass
air
N (1st
stage
operate:

o
o Ho 3 O CO CD > CO >
>; CO
CO c o
c o o

HEAVY
LOAD
•ST c
Closed

Small
amount
of
bypass
air

-co-CD CO
N (1st
stage
operate:

In CD 2? 03 a. o CD o> CO to "O c

*3 OFF (EGR)

o Ho 3 O CO CD > CO >
03 k-o CO c 03 CO z o *
CD c O) c 03 c o
c o o a 3

ACCELE-
RATION
Rich

o •*—• 3 o > CD
O

Small
amount
of
bypass
air

03 Q. O Q. E 3

ON

O
In CD 2? 03 a. o CD o> CO to "O c
ON
(EGR cut)
:F (Vacuum
to
pressure

regulatt

03 3 -C CO o
c 03 CS3 > X o o
z o * CO •o c CD Q. CD T3
C CO CD o "O 3= O c: 3 CO
LL LL o

MEDIUM
LOAD
WARM
Rich

and lean

|
Q. CD O
CD D
C CO E
CVJ.
z o fS *
*3 OFF (EGR)
:F (Vacuum
to
pressure

regulatt

E 3 3
c 03 i t 3 G, LL LL
T3 CD O c CO > "O <
C CO CD o "O 3= O c: 3 CO
LL LL o

MEDIUM
LOAD

COLD

ro
c CD 3 cr
z O "a CD a? CD CL o

F (2nd
stage
not
operated)
:F (Vacuum
to
pressure

regulatt

z o * O «

WARMING
UP

(DURING
IDLE)
Rich

CD CO c CD Q-O
o
c 3 CO O CO E CO
o c F (2nd
stage
not
operated)

tr O UJ
z o
O
LL z
Fixed

at

BTDC

12°

CRANKING
(COLD
ENGINE)
1
group
(twice

per

revolution)

CO
«
CD urn i CO
CO
LL LL O
LL O * « o o
LL LL o
Fixed
at

BTDC

6°

z o

SOLENOID
VALVE
(PRESSURE
REGU-

LATOR

CONTROL)

CC
o z o o iii z
o z 111

OUTPUT
DEVICE
FUEL

INJECTION

AMOUNT FUEL
INJECTION
TIMING
AIR

VALVE

'
ISC

VALVE
FUEL
PUMP

CONTROL
MAIN
POWER
CONTROL
SOLENOID
VALVE
(No.1
PURGE)
SOLENOID

VALVE

(NO.2

PURGE)
SOLENOID
VALVE
(EGR)
SOLENOID
VALVE
(PRESSURE
REGU-

LATOR

CONTROL)
SOLENOID
VALVE
(VARIABLE
INE
TIA
CONTROL)

> <
Ul oc oc o
£T u. O 1 z oc 3 m
oc o

OUTPUT
DEVICE
INJECTOR
BAC
VALVE
CONTROL
RELAY
SOLENOID
VALVE
(No.1
PURGE)
SOLENOID

VALVE

(NO.2

PURGE)
SOLENOID
VALVE
(EGR)
SOLENOID
VALVE
(PRESSURE
REGU-

LATOR

CONTROL)
SOLENOID
VALVE
(VARIABLE
INE
TIA
CONTROL)

tn z Ul (0 z Ul o >-X o
A/C

RELAY

IGNITER

z Ul (O
=5 o
IL oc <
76G04C-169
4C—94

CONTROL SYSTEM
4C

Output Devices
and
Engine Conditions (Leaded fuel)

REMARK

E Q
O O O r-»" CD > o n <

fuel
cut

'Coolant

temp.:

below

50°

(122°F)

*
During

hot
starting
only

*
Engine

speed:

above

5,400

rpm

'Delays

0.5

seconds

IGN:
ON
(ENGINE
I
NOT
RUNNING)

o
z
injection
No
bypass
OFF

(main

fuel

pump

not
operated)
OFF
LL
I

IDLE
(THROTTLE
VALVE
FULLY
CLOSED)
Rich

I
Sequential (once
per
two

revolutions)
"After

start-
ing:
ON

(vacuum

cut)
O

DECELE-
RATION

i

i
'Fuel

cut

•o CD CO "co" CD ts o to 3 o CO CD > CO
CO c o
c o o

HEAVY
LOAD
sz "co" c
O o CO CO CO Q. >. -O
O
CD Q. O CL E CL ® D
C CO F
o 08 3 u> £ CD 3 CO 0) CD
o to 3 o CO CD > CO
z

c o o c
B

ACCELE-RATION

ir o 3 0 > CD 1 O
C
O E CO
"CO
CD Q. O CL E CL ® D
C CO F
z

o 08 3 u> £ CD 3 CO 0) CD
CD e 3 SZ CO o
O * CO
c CD CL CD T3
c CO 8 "D

'
MEDIUM
LOAD
WARM
Normal

CD Q. CD O
E CO
z
O
o o_ O
E
3 3
o CO ^ LL LL O
E 3 3 O CO
•o "O <
c
3
m
LL LL o

'
MEDIUM
LOAD
COLD

.H C CD 3 CT
o_ O
E
3 3
o CO ^ LL LL O

z
o *

WARMING
UP

(DURING
IDLE)
Rich

CD CO

*Open

B
3
CO
O
CO
E
<®
LL
Fixed

at
BTDC
12°

CRANKING
(COLD
ENGINE)
1
group
(twice

per

revolution)

CO
«
0)
>,
u>n w-CO
o

OFF
Fixed

at

BTDC

6°
ENGINE
CONDITION
OUTPUT
DEVICE
FUEL
INJECTION

AMOUNT
'
FUEL
INJECTION

TIMING
AIR

VALVE
ISC
VALVE
FUEL
PUMP
CONTROL MAIN
POWER
CONTROL
SOLENOID
VALVE
(PRESSURE
REGU-

LATOR

CONTROL)
SOLENOID
VALVE
(VARIABLE
INER-
TIA
CONTROL)

(T ik 0 1 z DC 3
ffl

OC o tn

OUTPUT
DEVICE
INJECTOR
BAC
VALVE
CONTROL
RELAY
SOLENOID
VALVE
(PRESSURE
REGU-

LATOR

CONTROL)
SOLENOID
VALVE
(VARIABLE
INER-
TIA
CONTROL)

A/C

RELAY

IGNITER

Z Ul tn
£ o
ik DC <
76G04C-170
4C—95

4C CONTROL SYSTEM
EGI MAIN FUSE
Inspection
Check the continuity of EGI main fuse.
69G04A-161
CONTROL RELAY
Power Supply Circuit
1. Check that a "clicking" sound is heard at the con-
trol relay when turning the ignition switch ON and
OFF.
Note
The control relay is located under the center
console.
76G04C-171
2. Apply 12V to the 2B terminal and ground the 2D
terminal of the control relay.
3. Check voltage at the terminals with an voltmeter.
terminal
Terminals Grounded Not grounded
2C 12V OV
2E 12V OV
76G04C-172
From EGI From '9' From Ig. main fuse switch (ON) / switch
(ST)
To C/U / 9round To main To injector fuel Pump
Fuel Pump Circuit
1. Apply 12V and a ground to the terminals described
below and check the terminals with an ohmmeter
or voltmeter.
Terminal applied 12V
Terminal
grounded
Terminal checked
Correct condition
1B 1D 2F-1A Continuity
2F 1C 1A ADDrox.12V
76G04C-173
4C-96

4C CONTROL SYSTEM
Terminal Input Output Connection to Voltage (After warming-up) Remark Terminal Input Output Connection to Ign: ON Idle Remark
10 o Air flow sensor
(Burn-off control) Below 2.5V White burning off:
Approx. 8—12V
1P o
Control relay (Power supply circuit) Below 2.5V Ignition switch OFF:
Approx. 12V
1Q 0 Control relay (Fuel pump circuit) Approx. 12V Below 2.5V
1R
(L/F) O Knock sensor OV or 2—7V While knocking:
Approx. 0.001
1S — — — — —
1T o Ignition switch
(ON position) Approx. 12V
1U — — — — —
1V — — — — —
1W o Test connector Test connector grounded: OV Test connector not grounded: approx. 12V Green connector, 1-pin
1X o Igniter Approx. 12V *Approx.1V 'Engine Signal
Monitor: green and
red lights flash
2A (U/F) o V ref 4.5—5.5V
2B o Air flow sensor
(Ground) OV
2C — — Ground (E2) OV
2D (U/F) o Oxygen sensor OV 0-1.0V
• Cold engine: 0V at idle
• After warming-up: Increase engine speed: 0.7—1.0V Deceleration: 0—0.2V
2E o Air flow sensor
(Intake air mass) 1.0—1.6V 1.7—2.3V Increase engine speed: voltage increases
2F — — — .— —
2G (U/F) o Throttle sensor Accelerator pedal released: approx. 0.5V
Max. voltage (Throt-tle valve fully opened): approx. ,4.3V
2H (L/F) o Air flow sensor (Variable resister) 0-5V Depends on
adjustment
21 o Water thermo sensor Approx. 0.4V
Engine coolant
temp. 20°C (68°F):
approx. 2.5
2J o Intake air thermo sensor (Dynamic chamber)
Approx. 2.5V at 20°C (68°F)
2K o
Solenoid valve (Pressure regula-tor control)
For 120 sec. after ignition switch OFF - ON: below 2.5V
For 120. sec after starting: below 2.5V
During hot condi-tion: Coolant temp, above 70°C (158°F) Intake air temp, above 30°C (86°F) ...Unleaded fuel above 50°C (122°F) ...Leaded fuel
2K o
Solenoid valve (Pressure regula-tor control)
ADDrox. 12V Other conditions
2L — — — — —
Note
a) Terminal labeled "U/F" are only for unleaded fuel.
b)Terminal labeled "L/F" are only for leaded fuel.
4C-100

4D
FUEL AND EMISSION
CONTROL SYSTEM
(DIESEL)
OUTLINE 4D— 2
SPECIFICATIONS 4D— 2
TROUBLESHOOTING GUIDE 4D— 3
ON-VEHICLE MAINTENANCE 4D— 4
AIR CLEANER ELEMENT 4D— 4
WATER DRAINING 4D— 4
AIR BLEEDING 4D— 4
INJECTION TIMING 4D— 5
IDLE SPEED 4D— 6
EXHAUST SMOKE 4D— 6
INTAKE AIR SYSTEM 4D— 7
STRUCTURAL VIEW 4D— 7
AIR DUCT AND AIR CLEANER 4D— 8
INTAKE MANIFOLD 4D— 9
SUPERCHARGING SYSTEM (RF-CX) 4D-10
TROUBLESHOOTING GUIDE 4D—10
ON-VEHICLE INSPECTION 4D—11
COMPREX SUPERCHARGER 4D—13
STARTING VALVE 4D—15
INTERCOOLER 4D—16
BOOST AIR TEMPERATURE SENSOR 4D—17
EXHAUST SYSTEM 4D—18
STRUCTURAL VIEW 4D—18
EXHAUST MANIFOLD 4D—19
EXHAUST PIPE AND MAIN SILENCER .... 4D—20
FUEL SYSTEM 4D—21
STRUCTURAL VIEW 4D—21
FUEL FILTER 4D—22
SEDIMENTER (GENERAL) 4D—22
WATER LEVEL SENSOR 4D—23
INJECTION PUMP 4D—24
INJECTION NOZZLE 4D—31
FUEL TANK 4D—34
76G04D-001

4D OUTLINE
OUTLINE
The Mazda 626 offers two diesel engines; a Comprex supercharged RF-CX engine, and a normally
aspirated RF-N engine.
SPECIFICATIONS
—Engine model
Item ———
ECE UK, GENERAL —Engine model
Item ——— RF-CX RF-N
Fuel tank Capacity liters (US gal, Imp gal) 60 (15.9, 13.2)
Fuel filter Type Cartridge, paper element
Sedimenter Type With detector
Injection pump
Type Bosch VE distributor
Injection pump
Manufacturer Diesel Kiki Co,, Ltd.
Injection pump
Direction of rotation Clockwise Injection pump
Drive method Timing belt
Injection pump
Plunger diameter mm (in) 9.0 (0.35) 8.0 (0.31)
Injection pump
Cam lift mm (in) 2.2 (0.087)
Injection nozzle Type Throttle Injection nozzle
Injection pressure kPa (kg/cm2, psi) 13,240 (135 , 1,920)
Injection timing ATDC
1
° TDC 0°
Idle speed rpm 720 _+f0
Fast idle speed (A/C ON) rpm 700-750
Cold start device Engine speed rpm 1.100 Cold start device
Advance degree 6°
Air cleaner Type Cartridge, paper element Air cleaner Type
Wet Dry
PCV system Type Open Closed
76G04D-002
4D—2