fuel pump MAZDA 626 1987 Repair Manual

FUEL SYSTEM
4C

TROUBLESHOOTING
Checking the condition of the wiring harness and connectors before checking the sensors or switches.
Note
If
no
problem
is
found, continue with inspection
of the
next system
of
Troubleshooting
Guide. (Refer
to
page 4C—10,
and 11)

Possible cause 0 CO £ O ** CO £ O "5
Page


o CO c 0> (A
S o c
w O M C
.fc <0 "o
^ o w c 0) <0 c « o>
Im O CO c w w
0>
!
41 10 o E k 0) £ **
d>
5 <0 O E ^ 0) £
w 0

Fuel
pump
Injector Fuel
pressure

Engine control
unit terminal
a. E 3 a
a> » c

Transfer

pump

sv
(4WS)
ha c o o
if Qj
«> S£

< g. X O £ 1-ID a 5
Fuel
pump
Injector Fuel
pressure

1Q 3C,3E 3F,3H 3B ID k_ H
Transfer

pump

sv
(4WS) 3
C
U.
3

Symptom *C—103 4C—110 4C—107 4C—104 4C—107 4C—106 4C-56 4C-57 4C-54 4C-98 40-59
Hard start
or
won't start (Cranks
OK)
— — —-— g — 1 7 — 2 8 6 3 4 5
Engine During warm
up
4 — — — 3 — — 2 1 — 5 — — — —
stalls After warm
up
1 — — — — — — 3 2 — 4 — — — —
Rough During warm
up
5 — — — 3 — — 2 1 — 4 — — — —
a> 3 Idle After warm
up
1 6 — — 4 — — 3 2 — 5 — — — —
•o a> •o (0 a> c -»
Poor acceleration, hesi-tation,
or
lack
of
power 1 — — 3 5 — — 4 2 — 6 — — — — •o a> •o (0 a> c -» Runs
rough on
deceleration 1 — — — — — — 2 — — 3 — — — —
Afterburn on deceleration 1 — — — — — — 2 — — 3 — — — —
Poor fuel consumption 6 — 5 — 4 — — 2 1 — 3 — — — —
Engine stalls
or
runs rough after hot starting 1 5 — — — — — 3 2 — 4 — — — —
Falls emission test — — 1 — — 2 — 3 — — 4 — — — —
Hard start
or
won't
start (Cranks
OK)
— — — — 9 — 1 7 — 2 8 6 3 4 5
Engine During warm
up
4 — — — 3 — — 2 1 — 5 — — — —
stalls After warm
up
1 — — — — — — 3 2 — 4 — — — —
Rough During warm
up
— — — 3 — — 2 1 — 4 — — — —
a> 3 Idle After warm
up
1 6 — — 4 — — 3 2 — 5 — — — —
•o a> •o a
Poor acceleration, hesi-tation,
or
lack
of
power 1 — — — 4 — — 3 2 — 5 — — — —
a> Runs rough on deceleration 1 — — — — — — 2 — — 3 — — — —
Afterburn on deceleration 1 — — — — — — 2 — — 3 — — — —
Poor fuel consumption 5 — — — 4 — — 2 1 — 3 — — — —
Engine stalls
or
runs rough after
hot
staring 1 5 — — — — — 3 2 — 4 — — — —
Falls emission test 1 ?
76G04C-089
4C—51

4C FUEL SYSTEM
FUEL PRESSURE RELEASE AND SERVICING
FUEL SYSTEM
Fuel in the fuel system remains under high pressure
even when the engine is not running.
a) Before disconnecting any fuel line, release the fuel
pressure from the fuel system to reduce the pos-
sibility of injury or fire.
1. Start the engine.
2. Disconnect the 4-pin connector from the con-
trol relay or the fuel pump connector (5-pin or
6-pin).
3. After the engine stalls, turn OFF the ignition
switch.
4. Reconnect the relay or fuel pump connector.
b) Use a rag as protection from fuel spray when dis-
connecting the hoses.
Plug the hoses after removal.
c) When inspecting the fuel system, use the SST.
4C—52

4C FUEL SYSTEM
f-|To pulsation
-'damper
76G04C-092
Pressure regulator
How to Connect Multi-Pressure Tester
Warning
Before connecting the SST, release the fuel
pressure from the fuel system to reduce the
possibility of injury or fire. (Refer to page
4C—52.)
1. Disconnect the negative battery terminal.
2. Disconnect the fuel main hose from the fuel filter.
3. Connect the SST and adapter between the fuel
main hose and the fuel pump.
Caution
Do not reverse the adapter connection.
4. Disconnect the vacuum hose from the pressure
regulator. Connect the SST to the vacuum hose
with a three-way joint.
5. Connect the negative battery terminal.
6. Connect the SST to the battery.
76G04C-093
V „ Test connector (Yellow)
7. Connect the terminals of the test connector (Yel-
low) with a jumper wire. Turn the ignition switch
ON to operate the fuel pump.
8. Check for fuel leaks.
Caution
After checking for fuel leakage, turn the igni-
tion switch OFF and disconnect the jumper
wire from the test connector.
86U04A-072
FUEL PRESSURE
Note
Warm up the engine to normal operating tem-
perature.
Injection Pressure
1. Set the lever on the adapter as shown in the figure.
76G04C-094
4C-54

FUEL SYSTEM 4C
i i 1 1 1 i i
r.:.:::r t t t t t izn —i—i—i—i—i—i—i—i—
2DD 350
86U04A-074
2. Run the engine and measure the injection pres-
sure at various speeds.
Injection pressure: Approx. 235—275 kPa
(2.4—2.8 kg/cm2, 34—40 psi)
3. If not within specification, check the fuel pump pres-
sure and fuel line pressure.
Fuel Pump Pressure
1. Connect the terminals of the test connector (Yel-
low) with a jumper wire.
2. Turn the ignition switch ON to operate the fuel
pump.
3. Set the lever on the adapter as shown in the figure.
4. Check the fuel pump pressure.
Fuel pump pressure: 441—588 kPa
(4.5—6.0 kg/cm2, 64—85 psi)
5. If the fuel pump pressure is not within specifica-
tion, check the following;
No pressure
• Fuel pump operation (Refer to page
4C—56.)
Low pressure
• Fuel pump feeding capacity (Refer to
page 4C—56.)
High pressure
• Replace the fuel pump
6. After checking the fuel pump pressure, disconnect
the jumper wire from the test connector.
Fuel Line Pressure
1. Start the engine and run it idle.
2. Set the lever on the adapter as shown in the figure.
3. Check the fuel line pressure.
Fuel line pressure: Approx. 186—226 kPa
(1.9—2.3 kg/cm2, 27—33 psi)
4. If not within specification, check the pressure regu-
lator vacuum hose.
4C-55

4C FUEL SYSTEM
86U04A-078
76G04C-097
76G04C-098
„\W cLTest connector (Yellow)
'-/jumper wire \\ \ •
5. Disconnect the vacuum hose from pressure regu-
lator, and place a finger over the end of the hose.
6. Check the fuel line pressure.
Fuel line pressure: 235—275 kPa
(2.4—2.8 kg/cm2, 34—40 psi)
7. If not within specification, replace the pressure
regulator.
8. Connect the vacuum hose to pressure regulator.
FUEL PUMP
Operation Test
1. Connect a jumper wire to the test connector
(Yellow).
2. Remove the fuel filler cap.
3. Disconnect transfer pump connector (8-pin).
4. Turn the ignition switch ON.
5. Listen for operational sound of the fuel pump at
the filler inlet.
6. Install the fuel filler cap.
7. If no sound was heard, check the voltage at the
fuel pump connector (WY wire and a ground).
Voltage: 12V
8. If the voltage is normal, replace the fuel pump.
9. If not correct, check the control relay and circuit
(Refer to page 4C—96.)
10. Disconnect the jumper wire.
Volume Test
Warning
Before performing the following procedures,
release the fuel pressure from the fuel system
to reduce the possibility of injury or fire.
(Refer to page 4C—52)
1. Connect a jumper wire to test connector (Yellow).
2. Disconnect the fuel return hose from fuel return
pipe.
76G04C-099
4C-56

FUEL SYSTEM 4C
Pulsation damper
76G04C-100
Intake mainfold
3. Turn the ignition switch ON for 10 seconds, and
check the feeding capacity with graduated
cylinder.
Feeding capacity:
Minimum 220 cc (13.4 cu in)/10 sec.
4. If not within specification, check the fuel filter, fuel
lines and fuel pump.
5. Turn the ignition switch OFF and disconnect the
jumper wire.
PULSATION DAMPER
1. Run the engine at idle.
2. Place a finger on the screw of the pulsation damper
head.
3. Check that pulsation is felt.
86U04A-083

Injector
INJECTOR
On-vehicle Inspection
1. Warm up the engine and run it at idle.
2. Listen for operational sound of the injector with a
screwdriver or a sound scope.
76G04C-101
3. Ground the test connector (Green, 1-pin).
76G04C-102
4C-57

FUEL SYSTEM 4C
5. Connect the SST to the battery and injector.
6. Check the injection volume with a graduated con-
tainer.
Injection volume:
Approx. 66—91 cc (4.03—5.55 cu in) /15 sec.
Caution
When using the SST, make sure of the SST
number and use correct one.
7. If not correct, replace the injector.
76G04C-107
Rear seat Cushion Release Button -
76G04C-108
TRANSFER PUMP CONTROL SYSTEM (4 WHEEL
STEERING)
1. Remove the rear seat. (Refer to 14 section.)
2. Remove the fuel filler cap.
3. Turn the ignition switch ON.
Note
a) The tank should be more than 1/3 full.
b) Due to the delay timer, transfer pump oper-
ation begins approx. 10 sec. after the igni-
tion switch is turned ON.
4. Listen for the operational sound of the transfer
pump.
5. Install the fuel filler cap.
6. If no sound was heard, check the voltage at the
transfer pump connector.
Terminal (wire) Voltage
A, C (WG) Approx. 12V
I, J (B) OV
86U04B-075
I C A
lb d
cp a • • •
J
76G04C-211
7. If the voltages are correct, replace the transfer
pump.
8. If not correct, disconnect the transfer pump con-
nector.
9. Check the voltage at the terminals below.
Terminal (wire) Voltage
A, C (WG) Approx. 12V
I, J (B) OV
10. If the voltages are correct, replace the transfer
pump.
4C—59

4C FUEL SYSTEM
BW B
11. If not correct, check the voltage at terminals of the
fuel pump control unit.
76G04C-109
76G04C-110
86U04A-101
Fuel pump
Fuel filter
Bracket
76G04C-111
Terminal (wire) Voltage
A(B) Approx. 12V
C (BW) OV
12. If the voltages are correct, replace the fuel pump
control unit.
13. If not correct, repair the power supply circuit or the
ground circuit for the fuel pump control unit.
REPLACEMENT
Caution
A)Before performing the following procedure,
release the fuel pressure from the fuel sys-
tem to reduce the possibility of injury or fire.
(Refer to page 4C—52.)
b)When servicing the fuel system, keep
sparks, cigarettes, and open flames away
from the fuel.
Fuel Pump
1. Remove the rear seat and disconnect the fuel
pump connector.
2. Remove the service hole cover.
3. Disconnect the fuel hoses.
4. Remove the fuel pump and fuel tank gauge as-
sembly.
5. Replace the fuel pump.
Caution
Secure the fuel pump terminals and fuel hoses
tightly.
6. Install in the reverse order of removal.
4C—60

FUEL SYSTEM 4C
76G04C-112
86U04B-083
76G04C-113
Transfer Pump
1. Remove the fuel tank. (Refer to page 4C—65.)
2. Disconnect the fuel hoses from the transfer pump.
3. Remove the transfer pump.
4. Install in the reverse order of removal.
Injector
1. Remove the engine hanger.
2. Remove the wiring harness bracket.
3. Disconnect the PCV valve and hose from the dy-
namic chamber.
76G04C-114
4C-61

4C FUEL SYSTEM
^ Pulsation
damper
76G04C-121
Pulsation damper
—
Delivery pipe
76G04C-122
Fuel hose
,Fuel pump
-Intank filter
76G04C-123
Insulator
f f r—
/ 0 DM

•
II r
O - ring
Grommet
Manifold
Delivery pipe
Pressure Regulator
1. Remove the engine hanger.
2. Disconnect the vacuum hose and fuel return hose.
3. Remove the pressure regulator.
4. Install in the reverse order of removal.
Tightening torque:
8—11 Nm (0.8—1.1 m-kg, 69—95 in-lb)
Pulsation Damper
1. Remove the delivery pipe assembly. (Refer to page
4C-63.)
2. Remove the pulsation damper.
3. Install in the reverse order of removal.
Tightening torque:
25—34 N m (2.5—3.5 m-kg, 18—25 ft-lb)
Fuel Filter
Low pressure side (In-tank filter)
Refer to page 4C—60.
76G04C-124
High pressure side
The fuel filter must be replaced at the intervals out-
lined in the maintenance schedule.
Warning
Always work away from sparks or open
flames.
1. Disconnect the fuel hoses from the fuel filter.
2. Remove the fuel filter and the bracket.
3. Install a new filter and the bracket.
4. Connect the fuel hoses.
Note
When installing the filter, push the fuel hoses
fully onto the fuel filter and secure them with
spring clamps.
4C-64