Main battery MAZDA CX90 2024 Owners Manual

Be very careful of high temperature areas.
The hybrid system and the engine become hot when they operate. Follow the
instructions on the label attached to the vehicle and always pay attention to high
voltage areas and high temperature areas.
Do not touch the service plug.
A service plug is installed in the high voltage battery. This service plug is used at an
Authorized Mazda Dealer when repairing vehicles in order to cut off the high voltage
of the high voltage battery. Do not touch the service plug. If you handle the service
plug mistakenly, it could lead to an electrical shock causing serious injury or death.
1. Service plug
Maintenance and Repairs
For vehicle maintenance or repairs, consult an Authorized Mazda Dealer.
Technical knowledge and skill are necessary in handling the high voltage battery.
WARNING
To ensure safe and correct handling of the high voltage battery, always heed the
following precautions.
 Do not remove the high voltage battery.
 Do not resell, transfer, or modify the high voltage battery.
 Do not make secondary use of the high voltage batter.
If the drive battery is not handled properly, the following may occur which could
lead to serious injury or death.
 Touching an unattended high voltage battery may cause an electric shock.
 If the high voltage battery is used on a vehicle other than the one it came
equipped on (including modified vehicles), accidents such as electric shock, heat
generation, smoking, combustion, and explosions, or an electrolyte leakage may
occur.
Heed the following instructions to prevent deterioration of the high voltage battery
or damage to the high voltage battery.
Do not leave the vehicle for a long time under extremely high or low temperature
conditions.
Do not leave the vehicle for 14 days or longer while the high voltage battery power
gauge is at Empty (level 0).
Driving
e-SKYACTIV PHEV
5-20
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

WARNING
Appropriate disposal of the high voltage battery.
If the high voltage battery is not collected and disposed of appropriately, such as by
leaving it unattended or illegally abando ning it, some other person may touch it
which could cause electrocution leading to serious injury.
Fuel
CAUTION
 The e-SKYACTIV PHEV can be driven on electricity, but depending on the driving
conditions and mode, the vehicle will be driven using the engine and will need to
be refueled. Check the remaining amount of fuel and replenish the fuel if
necessary.
Refer to How to Use the Mazda intelligent Drive Select (Mi-Drive) on page 5-96.
 Depending on the vehicle usage conditions, fuel may remain in the tank for a long
period of time and the quality of the fuel may change. Refuel at least 25 L of fuel
every 12 months (total amount of refueling for 12 months is at least 25 L), as this
may affect parts of the fuel system and the engine.
 If the fuel has not been replenished for a certain period of time and the quality of
the fuel in the fuel tank is expected to change, a message is displayed in the
instrument cluster when the hybrid system is started. When a certain amount of
fuel is consumed, the message displayed in the instrument cluster is no longer
displayed.
Driving
e-SKYACTIV PHEV
5-22
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the
e-SKYACTIV PHEV
Switching the Drive Mode
You can switch the drive mode of the
hybrid system by operating the switch.
TOWING mode/SPORT mode/
NORMAL mode/EV mode/
OFF-ROAD mode
Refer to How to Use the Mazda
intelligent Drive Select (Mi-Drive) on
page 5-96.
CHARGE Mode
The engine is used as a generator, and
the vehicle is driven while charging the
high voltage battery.
1. Start the hybrid system.
2.
When CHARGE mode is activated, the
CHARGE mode indicator light
in
the instrument cluster turns on.
Power is generated to the preset target
charge amount, and when the target
charge amount is reached, power is
generated to maintain it.
NOTE
Switching to CHARGE mode may not
be possible depending on the
conditions of the hybrid system.
When power consumption is high
due to the vehicle driving conditions,
outside air temperature, or when the
air conditioner is used, charging may
take longer than usual or may not
occur.
When the vehicle is driven while in
CHARGE mode, the engine operates
to generate electricity, therefore fuel
consumption may increase
compared to when driving the
vehicle in a mode other than
CHARGE mode.
If the vehicle power is switched OFF
while switching the mode to
CHARGE mode, the CHARGE mode
will be canceled the next time the
vehicle power is switched ON.
When pressing the charge mode
switch while the Mazda intelligent
Drive Select (Mi-Drive) is in EV
mode, the Mi-Drive switches to
NORMAL mode and the vehicle is
driven in CHARGE mode.
The mode may not be able to switch
to CHARGE mode when the fuel is
low.
The target charge amount can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Po we r Me te r
Displays in the instrument cluster while
driving in NORMAL mode or EV mode.
Driving
e-SKYACTIV PHEV
5-23
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Convenient Ways to Usethe e-SKYACTIV PHEV
Switch to Start in EV Mode
The hybrid system can be changed to
start in EV mode.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Switching the Regenerative Braking
Strength
The regenerative braking strength can
be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
For Eco-Friendly and Economical
Driving
Using the Drive Mode
EV mode is mainly used in urban areas,
while NORMAL mode is used in
suburban areas and on expressways,
which leads to savings in electricity and
fuel consumption.
By actively using regenerative braking
to charge the high voltage battery, it is
possible to increase the EV travel
distance and to reduce fuel
consumption when driving the vehicle
in a mode other than EV mode.
To extend cruising distance
The electrical power consumption
while driving can be reduced and the
cruising distance can be extended by
doing the following operations.
With the charge connector
connected, turn on the climate
control system to provide a
comfortable temperature in the
cabin before driving.
When driving during cold
temperatures, use the seat warmer or
steering warmer instead of the
climate control system.
Adjust the climate control system to
a moderate airflow and temperature
setting.
Refrain from using the defogger
under conditions other than when a
window is fogged or frozen.
By maintaining a sufficient distance
between vehicles and using the
regenerative braking well, more
electrical power can be charged to
the high voltage battery.
To extend the life of the high voltage
battery
The high voltage battery life changes
depending on the vehicle storage
conditions or charging method.
To extend the life of the high voltage
battery, be careful of the following.
(Charging the battery)
Avoid unnecessary, frequent
charging.
Only charge the battery with as much
power as needed, and do not always
fully charge the battery. The
maximum charge limit can be set.
Refer to Convenient Ways to Use of
Charging on page 5-118.
(Parking the vehicle)
Do not park the vehicle in a place
where the ambient temperature is
extremely high or low.
Do not leave the vehicle while the
remaining high voltage battery power
is extremely low.
If the [Battery Cooling] operation notification is displayed on the
center display after driving the
vehicle, select [Activate].
Driving
e-SKYACTIV PHEV
5-25
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Remaining Charge and Temperature
of the High Voltage Battery
If the high voltage battery level is low
or the high voltage battery temperature
is low, the vehicle speed may not
increase even if the accelerator pedal is
depressed because the motor output is
restricted. Check the contents
displayed in the instrument cluster and
the remaining amount of power in the
high voltage battery before driving.
(Battery cooling)
If the high voltage battery temperature
is high after driving the vehicle, it is
possible to cool the high voltage
battery while the vehicle is parked to
extend the life of the high voltage
battery. If the Excessive Battery
Te m p e ra t u r e notification is displayed
on the center display after driving the
vehicle, select Start to start the battery
cooling.
NOTE
Because the electrical power of the
high voltage battery is used by the
battery cooling , we recommend that
the charge connector is connected
while the battery cooling is operating.
Driving
e-SKYACTIV PHEV
5-26
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the
Odometer/Trip Meter

The display changes each time the TRIP
switch is pressed.
1. Odometer display
2. Trip meter A display
3. Trip meter B display

When returning the trip meter to “0”,
press the TRIP switch for 2 seconds or
longer while the trip meter is
displayed.
NOTE
If the lead-acid battery is disconnected
for vehicle maintenance or other
reasons, the trip meter display returns
to “0”.
High Voltage Battery Temperature Gauge
Displays the high voltage battery
temperature. The blue range of the
gauge indicates that the high voltage
battery temperature is low and the red
range indicates that it is high and
overheating.

Driving
Instrument Cluster
5-33
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Engine Coolant
Temperature Gauge
Displays the engine coolant
temperature. The blue range of the
gauge indicates that the engine coolant
temperature is low, and the red range
of the gauge indicates that the engine
coolant temperature is high and
overheating.

CAUTION
If the engine coolant temperature
gauge needle is in the red range, there
is the possibility of overheating. Drive
slowly to reduce engine load.
Refer to Taking Action with
Overheating on page 8-20.
High Voltage Battery Powe r G au ge
The remaining power of the high
voltage battery is indicated when the
vehicle power is switched ON.
When the high voltage battery is fully
charged, F is indicated. As the level
lowers, the needle approaches E.

NOTE
After charging, it may require some
time for the needle to stabilize.
The arrow indicates that the
charging port is on the right side.
Driving
Instrument Cluster
5-34
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Outside TemperatureDisplay
When the vehicle power is switched
ON, the outside temperature is
displayed.

NOTE
The outside temperature display may
differ from the actual outside
temperature depending on the
surroundings and vehicle conditions.
Maximum Driving
Distance Display
The maximum driving distance is
calculated and displayed based on the
current remaining charge of the high
voltage battery/fuel tank level and the
electrical power consumption rate/
fuel economy. When the maximum
driving distance is 50 km (30 miles) or
farther, the maximum driving distance
indication decreases in 10 km (10
mile) increments, and when the
maximum driving distance is 50 km
(30 miles) or shorter, it decreases in 1
km (1 mile) increments.
1. Remaining distance-to-full discharge display for high voltage
battery only
2. Maximum driving distance display for fuel and high voltage battery
NOTE
The maximum driving distance is just
an approximate numerical value and
differs from the actual driving distance.
Drive the vehicle while checking the
high voltage battery power gauge/fuel
gauge.
Driving
Instrument Cluster
5-37
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

(SPORT Mode)
(NORMAL Mode)
(EV Mode)
(OFF-ROAD Mode)
NOTE
TOWING mode can be selected only
when electrically connected to the
trailer using a Mazda genuine trailer
hitch. In addition, it may take some
time until the connection is detected
and TOWING mode is displayed.
Consult an Authorized Mazda Dealer
for details.
Depending on driving conditions
when selecting TOWING mode/
SPORT mode/OFF-ROAD mode, the
vehicle may perform shift-down or
accelerate slightly.
When SPORT mode/OFF-ROAD
mode is selected, driving the vehicle
at higher engine speeds increases
and fuel economy may worsen.
Canceling SPORT mode/OFF-ROAD
mode during normal driving is
recommended.
When setting the Mazda Radar
Cruise Control (MRCC) while driving
in SPORT mode, the mode is
switched to NORMAL mode. In
addition, while the MRCC is being
used, the mode cannot be switched
to SPORT mode.
Switching to EV mode may not be
possible depending on the driving
operations, driving conditions, and
high voltage battery condition.
When the system determines that
the engine needs to be started while
the vehicle is being driven in EV
mode, the mode is switched to
NORMAL mode.
The remaining distance-to-full
discharge for EV mode may
decrease, even when the vehicle is
being driven in a mode other than
EV mode.
The maximum speed in EV mode is
140 km/h (86 mph).
The drive mode cannot be switched
in the following cases.
The Antilock Brake System (ABS) is
operating.
The Traction Control System (TCS)
is operating.
The Dynamic Stability Control
(DSC) is operating.
The steering wheel is being
operated abruptly.
The driving mode in which the
display in the instrument cluster is
grayed out cannot be selected.
When the vehicle power is switched
OFF, the mode returns to NORMAL
mode. However, TOWING mode
before switching the vehicle power
OFF is maintained only when the
trailer is connected in TOWING
mode.
Driving
Mazda intelligent Drive Select (Mi-Drive)
5-97
CX-90_8KG7-EA-22L_Edition1_new2022-11-17 16:05:04

Charge indicator
The illumination/flash pattern of the
charge indicator can be checked using
the labels on the charge lid.
Charge indicator
illumination/flash pattern Content
— OFF Charging is possible.
(White) ON
Turns on when waiting for
starting to charge.
(White) Flashes
slowly The brightness changes
when the charging timer is
set.
(Green)
Flashes
slowly The brightness changes
during charging.
(Green)
ONTu r n s o n w h e n c h a rg i n g i s
completed.
Turns off after a certain pe-
riod of time has passed
since charging was com-
pleted.
(Amber)
FlashesFlashes when the charging
connector is connected and
the selector lever is in a po-
sition other than P.
Shift the selector lever to
the P position.
Charge indicator
illumination/
flash pattern Content
(Amber)
ONTurns on if there is a prob-
lem with the charging sys-
tem when the charging
connector is connected.
Wait a few minutes then re-
connect the charging con-
nector.
(Red)
ONTurns on if there is a prob-
lem with the charging sys-
tem and the charging port
lid is opened or the charg-
ing connector is connected.
Have your vehicle inspect-
ed by an Authorized Mazda
Dealer.
Charge status screen
When the driver's door is opened
while the charge connector is
connected, the charging status is
displayed in the instrument cluster.
1. Charge status icon
2. Message
3. Remaining power of the high
voltage battery (Displayed only
when vehicle power is switched
OFF)
4. Time to complete charging
5. EV maximum driving distance (Displayed only when vehicle
power is switched OFF)
Driving
Charging
5-117
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04