is low MAZDA CX90 2024 Manual PDF
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2024, Model line: CX90, Model: MAZDA CX90 2024Pages: 687, PDF Size: 15.46 MB
Page 131 of 687

Your foot remains placed within
the detection area.
You move your foot left and right
within the detection area.
The kicking motion is too fast or
too slow.
Your foot contacts the rear bumper
when doing the kicking motion.
You are wearing shoes such as
rubber boots which do not
conduct electricity well.
There is equipment emitting strong
radio waves near the vehicle.
The detection area of the
hands-free sensor is dirty.
When the detection area of the
hands-free sensor is dirty, wipe it off
with a clean cloth. Before cleaning
the sensor, place the key outside of
its operation range or turn off the
hands-free function using Mazda
Connect.
If the operation using the hands-free
sensor is not possible even though
the operation conditions are met,
consult an Authorized Mazda Dealer.
Hands-free function ON/OFF
switching
The hands-free function can be
switched on/off.
Refer to Mazda Connect Owner's
Manual or consult an Authorized
Mazda Dealer.
To prevent an unintended operation,
turn off the function.
Stopping the liftgate
If any of the following operations is
done, the automatic opening and
closing of the liftgate stops.
The liftgate open/close switch on the
key is pressed.
The power liftgate switch is pressed.The electric liftgate opener is
pressed.
The power liftgate close switch is
pressed.
The door-lock switch on the liftgate
is pressed.
The kicking motion is done.
NOTE
The liftgate cannot be stopped when it
is half open or lower. It moves in the
close direction by the load weight of
the liftgate itself.
The automatic opening/closing of the
liftgate can be stopped using the
kicking motion even if you do not have
the key.
Moving the liftgate again
If any of the following operations is
done, the liftgate moves in the
direction opposite to the direction it
was moving before it stopped.
The liftgate open/close switch on the
key is pressed for 1 second or longer.
The power liftgate switch is pressed
for about 1 second or longer.
The electric liftgate opener is
pressed.
The power liftgate close switch is
pressed.
When the door-lock switch on the
liftgate is pressed, the liftgate
automatically fully closes.
Opening/closing
Liftgate
4-24
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 134 of 687

How to Use the Hood
Opening the Hood
1. Pull the hood release handle.The hood will raise slightly.
2. When the hood is raised by about40 cm, it opens automatically.
When the hood is opened to a
certain position, it is held open.
NOTE
If you push up from the position where
the hood has stopped, you can open
the hood further.
Closing the Hood
1. Make sure that there are no toolsleft in the engine compartment.
2. Lower the hood slowly and release it from a height of about 35 cm
without applying excessive force.
The hood closes.
NOTE
When the hood is closed by pushing it
with a hand, it may not be locked
normally. If the hood does not close
completely, open it again and operate
it slightly more strongly using the same
method.
Opening/closing
Hood
4-27
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 135 of 687

Powe r Wi n d ow s
The power window has two functions.
Auto-opening/Closing Function
The windows can be fully opened and
closed without having to continue
operating the power window switch.
Jam-Safe Function
If a foreign object is detected between
the window and the window frame
while the window is closing , the
window stops closing and opens
slightly.
NOTE
The power windows cannot be
opened from the outside of the
vehicle if the power window
initialization has not been
completed.
Refer to Initializing the Power
Window on page 8-31.
(A window cannot be closed)
If the jam-safe function has operated
and the window cannot be closed,
check around the window frame for
a foreign object.
If there is no foreign object around
the window frame, forcibly close a
window using the following
procedure.
1. After switching the vehicle powerOFF, wait for 45 seconds or
longer.
2. Switch the vehicle power ON.
3. Operate the switch in the direction to close the window
until the jam-safe function
operates and the window stops.
Repeat this operation a total of 5
times.
4. Continue pulling up the switch to fully close the window.
Warnings and Cautions
for Using the Power Windows
WARNING
When closing the windows, be careful
that a passenger’s hand or head does
not get pinched.
Be especially careful with children. If a
hand or head becomes pinched, it
could cause serious injury.
Do not let a child operate the power
window switches.
If a hand or head becomes pinched, it
could cause serious injury.
Keep the power window lock switch
in the lock position when carrying a
child.
If the child operates the power
window switch incorrectly and a hand
or head becomes pinched, it could
cause serious injury.
Make sure that there is nothing
blocking the window just before it
closes completely or while the power
window switch is being pulled.
The jam-safe function may not be able
to prevent the window from closing
completely. If a finger gets pinched, it
could cause serious injury.
Do not let a child put a hand or head
out of the window.
Be careful not to let a child put a hand
or head out of the window while
driving the vehicle. If the child's hand
or head hits something outside the
vehicle or sudden braking is applied, it
could result in seri ous injury or death.
Opening/closing
Windows
4-28
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 137 of 687

Convenient Ways to Usethe Power Windows
Operation Function After Vehicle
power is Switched OFF
All the windows can be opened and
closed for approximately 40 seconds
after the vehicle power is switched to
ACC or OFF with all doors closed. If
any door is opened, the power
window will stop operating.
Remote Power Window Operation
All power windows can be opened
from outside the vehicle after the
doors are closed.
The power windows can be operated
remotely when the power window lock
button on the driver's door is in the
lock or unlocked position.
Remote power window operation is
activated under the following
conditions.
All the doors and liftgate are closed.The vehicle power is switched OFF.
NOTE
The power windows cannot be
opened from the outside of the vehicle
if the power window initialization has
not been completed.
Opening
The windows can be opened for
ventilating the cabin before getting in
the vehicle.
Press the unlock button on the key
quickly and briefly 3 times and then
immediately afterwards, press and
hold the unlock button to open the
windows.
To stop the windows from opening ,
release the button. If the operation is
performed from the beginning again,
the windows open.
Opening/closing
Windows
4-30
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 138 of 687

Panorama Sunroof*
The panorama sunroof can be opened
or closed when operating the
overhead tilt/slide switch at the front
seats.
1. Tilt/slide switch
Jam-safe function
If foreign matter caught between the
panorama sunroof and the window
frame is detected while it is closing
automatically, the panorama sunroof
stops and opens partway.
NOTE
When the jam-safe function is
inoperable, the panorama sunroof
initial setting is not performed.
Refer to Initializing the Panorama
Sunroof on page 8-32.
Warnings and Cautions
for Using the Panorama Sunroof
WARNING
When closing the panorama sunroof,
be careful that a passenger’s hand or
head does not get pinched.
If a hand or head becomes pinched, it
could cause serious injury.
Do not let a child operate the tilt/
slide switch.
If a hand or head becomes pinched, it
could cause serious injury.
Do not allow a passenger to put a
hand or head out of the area where
the panorama sunroof opens while
driving the vehicle.
If the person's hand or head hits
something outside the vehicle, or
sudden braking is applied, it could
result in serious injury or death.
While driving, do not let occupants
stand up and extend a part of their
body out of the opening.
Extending your head, arms, or other
parts of your body from the panorama
sunroof is dangerous. Your head or
arm may hit something while driving,
which could result in a fatal injury.
Just before the panorama sunroof
completely closes, make sure there is
nothing obstructing the panorama
sunroof.
The jam-safe function may not prevent
the panorama sunroof from closing
completely. Getting your fingers
pinched could cause serious injury.
Opening/closing
Sunroof
*Some models.4-31
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 141 of 687

Moonroof*
The moonroof can be opened or
closed when operating the overhead
tilt/slide switch at the front seats.
1. Tilt/slide switch
Jam-safe function
If foreign matter caught between the
moonroof and the window frame is
detected while it is closing
automatically, the moonroof stops and
opens partway.
NOTE
Before leaving the vehicle or washing
your Mazda, make sure the
moonroof is completely closed so
that water does not get inside the
cabin area.
After washing your Mazda or after it
rains, wipe the water off the
moonroof before operating it to
avoid water penetration which could
cause rust and water damage to your
headliner.
The jam-safe function may operate
under the following conditions.
A strong impact is detected while
the moonroof is closing
automatically.
The moonroof is closing
automatically during very low
temperatures.
When the jam-safe function is
inoperable, the moonroof initial
setting is not performed.
Refer to Initializing the moonroof on
page Reference 8-33.
Opening/closing
Sunroof
4-34*Some models.
CX-90_8KG7-EA-22L_Edition1_new2022-11-17 16:05:04
Page 142 of 687

Warnings and Cautions
for Using the Moonroof
WARNING
Do not let passengers stand up or
extend part of the body through the
open moonroof while the vehicle is
moving.
Extending the head, arms, or other
parts of the body through the
moonroof is dangerous. The head or
arms could hit something while the
vehicle is moving. This could cause
serious injury or death.
Never allow children to play with the
tilt/slide switch.
The tilt/slide switch would allow
children to operate the moonroof
unintentionally, which could result in
serious injury if a child's hands, head
or neck becomes caught by the
moonroof.
Make sure the opening is clear before
closing the moonroof.
A closing moonroof is dangerous. The
hands, head, or even neck of a person,
especially a child, could be caught in it
as it closes, causing serious injury or
even death.
Make sure nothing blocks the
moonroof just before it reaches the
fully closed position.
Blocking the moonroof just before it
reaches the closed position is
dangerous.
In this case, the jam-safe function
cannot prevent the moonroof from
closing. If fingers are caught, serious
injuries could occur.
CAUTION
Do not sit on or put heavy items on
the area where the moonroof opens
and closes. Otherwise, the
moonroof could be damaged.
Do not open or close the moonroof
forcefully during freezing
temperatures or snowfall. Otherwise,
the moonroof could be damaged.
The sunshade does not tilt. To avoid
damaging the sunshade, do not push
it up.
Do not close the sunshade while the
moonroof is opening. Trying to force
the sunshade closed could damage
it.
Opening/closing
Sunroof
4-35
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 145 of 687

Immobilizer System
The immobilizer system allows the
hybrid system to start only with a key
the system recognizes.
NOTE
The keys carry a unique electronic
code. For this reason, and to assure
your safety, obtaining a replacement
key requires security validation, this
will add some delays in supplying a
replacement key. They are only
available through an Authorized
Mazda Dealer.
Always keep a spare key in case one
is lost. If a key is lost, consult an
Authorized Mazda Dealeras soon as
possible.
If you lose a key, an Authorized
Mazda Dealer will reset the
electronic codes of your remaining
keys and immobilizer system. Bring
all the remaining keys to an
Authorized Mazda Dealerto reset.
Warnings and Cautions
for Using the Immobilizer System
CAUTION
Radio equipment like this is
governed by laws in the United
States.
Changes or modifications not
expressly approved by the party
responsible for compliance could
void the user's authority to operate
the equipment.
To avoid damage to the key, do not:
Drop the key.
Get the key wet.
Expose the key to any kind of
magnetic field.
Expose the key to high
temperatures on places such as the
dashboard, under direct sunlight.
If the hybrid system does not start
with the correct key, and the security
indicator light keeps illuminating or
flashing , the system may have a
malfunction. Consult an Authorized
Mazda Dealer.
Opening/closing
Security System
4-38
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 146 of 687

How to Use the
Immobilizer System
NOTE
The hybrid system may not start and
security indicator light may illuminate
or flash if the key is placed in an area
where it is difficult for the system to
detect the signal, such as on the
dashboard or in the glove
compartment. Move the key to a
location within the signal range,
switch the vehicle power off, and
then restart the hybrid system.
Signals from a TV or radio station, or
from a transceiver or mobile
telephone could interfere with your
immobilizer system. If you are using
the proper key and the hybrid system
fails to start, check the security
indicator light.
Arming
The system is armed when the vehicle
power is switched from ON to off.
The security indicator light
in the
instrument cluster flashes every 2
seconds until the system is disarmed.
Disarming
The system is disarmed when the
vehicle power is switched ON with the
correct programmed key. The security
indicator light
illuminates for
about 3 seconds and then turns off.
If the hybrid system does not start with
the correct key, and the security
indicator light remains illuminated or
flashing , try the following:
Make sure the key is within the
operat ional range for signal
transmission. Switch the vehicle power
off, and then restart the hybrid system.
If the hybrid system does not start after
3 or more tries, contact an Authorized
Mazda Dealer.
Opening/closing
Security System
4-39
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 147 of 687

Theft-Deterrent System
If the theft-deterrent system detects an
inappropriate entry into the vehicle,
which could result in the vehicle or its
contents being stolen, the alarm alerts
the surrounding area of an abnormality
by sounding the horn and flashing the
hazard warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
How to Use the
Theft-Deterrent System
How to Arm the System
1. Close the windows and the
panorama sunroof/moonroof*
securely.
2. Switch the vehicle power OFF.
3. Make sure the hood, the doors, and the liftgate are closed.
4. Press the lock button on the transmitter. The hazard warning
lights will flash once.
The following method will also arm
the theft-deterrent system:
Press the door-lock switch
while
any door is open and then close all
of the doors.
( With the advanced keyless
function)
Touch the sensing area of the door
lock touch sensor.
The security indicator light
in
the instrument cluster flashes twice
per second for 20 seconds.
5. After 20 seconds, the system is fully armed.
NOTE
The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate and the hood closed.
Refer to Transmitter on page 4-5.
The system will disarm if one of the
following operations takes place
within 20 seconds after pressing the
lock button:
Unlocking any door.Opening any door.Opening the hood.Switching the vehicle power ON.
To rearm the system, do the arming
procedure again.
Opening/closing
Security System
4-40*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04