torque MAZDA MIATA 1991 Factory User Guide

Fig. 3: Removing Axle Shaft From Hub Assembly
Courtesy of MAZDA MOTORS CORP.
2. Remove upper control arm bolt, and pull knuckle/hub assembly outward. Remove inner CV joint from
differential flange. Remove axle shaft from knuckle/hub assembly. If axle shaft is stuck in knuckle/hub
assembly, use plastic or soft-faced hammer to tap axle shaft from knuckle/hub assembly. See Fig. 3
.
Remove axle shaft lock nut.
Installation
To install, reverse removal procedure. Align marks on differential and axle shaft flanges. Check rear wheel
alignment. See appropriate article in WHEEL ALIGNMENT. Tighten all bolts and nuts to specification. See
TORQUE SPECIFICATIONS
. Stake axle shaft lock nut. See Fig. 4.
NOTE: Manufacturer recommends using new axle shaft lock nut during installation.

1991 Mazda MX-5 Miata
1990-93 DRIVE AXLES Axle Shafts - MX-5 Miata
Microsoft
Sunday, July 05, 2009 2:16:33 PMPage 4 © 2005 Mitchell Repair Information Company, LLC.

Fig. 16: Installing Boot Band
Courtesy of MAZDA MOTORS CORP.
AXLE SHAFT LENGTH
REAR AXLE SHAFT BOOT IDENTIFICATION
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
ApplicationIn. (mm)
1990
On Vehicle25.96 (659.3)
Off Vehicle25.97-26.37 (695.7-669.7)
1991-93
On Vehicle25.87 (657)
Off Vehicle25.30-26.68 (642.6-677.7)
ApplicationIn. (mm)
Wheel Side Diameter3.58 (90.8)
Differential Side Diameter3.44 (87.4)

1991 Mazda MX-5 Miata
1990-93 DRIVE AXLES Axle Shafts - MX-5 Miata
Microsoft
Sunday, July 05, 2009 2:16:33 PMPage 16 © 2005 Mitchell Repair Information Company, LLC.

Fig. 26: Typical Master Cylinder (Except Navajo & 929)
Courtesy of MAZDA MOTORS CORP.
SPECIFICATIONS
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
ApplicationFt. Lbs. (N.m)
Backing Plate (Rear)
B2200 & B2600i 2WD72-87 (98-118)
B2600i 4WD65-80 (88-108)
Navajo25-35 (34-47)
All Others33-43 (45-58)
Caliper Guide Bolt
B2200 & B2600i23-30 (31-41)

1991 Mazda MX-5 Miata
BRAKE SYSTEM 1991 BRAKES Mazda Brake System
Microsoft
Sunday, July 05, 2009 2:18:09 PMPage 37 © 2005 Mitchell Repair Information Company, LLC.

Removal (Front - B2600i & MPV 4WD)
1. Raise and support vehicle. Remove engine skid plate. Drain differential. On MPV 4WD, remove tie rod
end and lower arm. Remove front axle shafts. See AXLE SHAFTS
- FRONT article. Mark drive shaft
position, and remove drive shaft.
2. On B2600i, remove differential subframe mounting bolts and nuts. Remove differential, Remote Free
Wheel (RFW) and subframe assembly from vehicle. Remove RFW assembly from right side of
differential housing. Pull drive coupler from carrier. Remove differential carrier retaining bolts. Remove
differential carrier.
3. On MPV 4WD, remove differential housing mounting bolts and mount at end of Remote Free Wheel
(RFW) extension housing. Remove differential and extension housing from vehicle. Remove RFW
assembly from right side of differential housing. Pull drive coupler from carrier. Remove differential
carrier retaining bolts. Remove differential carrier.
Installation
To install, reverse removal procedure. See Fig. 2 or Fig. 3 . Apply Sealant (8527 77 739 ) to carrier mating
flange. Align marks made during removal. Refill differential with lubricant. Tighten all fasteners to
specification. See TORQUE SPECIFICATIONS
.

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 5 © 2005 Mitchell Repair Information Company, LLC.

B2600i and MPV, remove brake drum and drive axles. See REAR AXLE SHAFTS & BEARINGS. On
Protege 4WD, RX7 and 929, disconnect CV joint drive axles from differential assembly and wire aside.
2. On all models, mark flanges and disconnect drive shaft. Remove ABS sensor (if equipped). On RX7,
remove rear exhaust system and differential mount on left side of pinion flange. Remove hanger mounts
and allow left side to hang down. Disconnect sublinks and remove differential.
3. On Protege 4WD and 929 models, remove differential housing assembly-to-chassis mounting bolts.
Remove differential housing assembly from vehicle. On all models, remove differential carrier-to-
housing nuts. Remove differential carrier.
Installation
To install, reverse removal procedure. Apply Sealant (8527 77 739 ) to carrier mating flange. Align marks made
during removal. Refill differential with correct type and amount of lubricant. Tighten all fasteners to
specification. See TORQUE SPECIFICATIONS
.
Fig. 4: Exploded View of Differential Assembly (RX7)

Courtesy of MAZDA MOTORS CORP.
Removal (Miata)
1. Raise and support vehicle. Drain differential. Mark flanges and remove drive shaft. Note locations and
disconnect wiring harness from Power Plant Frame (PPF). See Fig. 5
.

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 8 © 2005 Mitchell Repair Information Company, LLC.

2. Support transmission with a jack. Remove PPF bracket from rear transmission extension housing.
Remove PPF-to-differential side bolts and pry out spacer. Remove PPF/differential mounting spacer. See
Fig. 6
. Install metric bolt (M14 X 1.5) into sleeve. See Fig. 7 .
3. Twist bolt side-to-side while pulling bolt downward. Install a metric bolt (M6 X 1) into hole in housing
block to hold sleeve and remove long bolt (M14 X 1.5). Remove short bolt (M6 X 1).
4. Remove PPF-to-transmission side bolts and remove PPF. Mark and disconnect CV joint drive axles from
differential assembly and wire aside. Remove differential carrier-to-housing nuts. Remove differential
carrier.
INSTALLATION
1. To install, reverse removal procedure. Apply Sealant (8527 77 739 ) to carrier mating flange. Align marks
made during removal and install differential carrier. Install differential. Raise transmission until engine
and transmission are level.
2. To install Power Plant Frame (PPF), position PPF in place. Install PPF/differential mounting spacer and
tighten bolts to 27-38 ft. lbs. (37-52 N.m). Install PPF-to-transmission side mounting bolts and tighten.
3. Ensure sleeve is installed into PPF housing block. Install spacer and bolts. Ensure reamer bolt is installed
into front hole and tighten. See Fig. 6
.
4. Install transmission-to-PPF bracket. Install remaining PPF bolts and tighten all bolts to specification. See
TORQUE SPECIFICATIONS
. To complete installation, reverse removal procedure.
NOTE: On Miata, front PPF-to-differential side mounting bolt is reamer bolt, which
aligns power plant frame. See Fig. 6
.

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 9 © 2005 Mitchell Repair Information Company, LLC.

Fig. 12: Measuring Carrier Case Spread
Courtesy of MAZDA MOTORS CORP.
TORQUE SPECIFICATIONS
1990 TORQUE SPECIFICATIONS (B2200 & B2600i)
ApplicationFt. Lbs. (N.m)
Brake Pipe Union10-16 (14-22)
Differential Assembly
Differential Carrier-to-Axle Housing17-20 (23-27)
Differential Carrier Bearings Cap Bolts
"P" Series Differential41-59 (56-80)
"M" Series Differential27-38 (37-52)
Differential Carrier
Bearings Lock Tab13-19 (18-26)
Drive Pinion Lock Nut94-130 (127-176) 90
Filler Plug29-40 (39-54)
Ring Gear Retaining Bolts51-61 (69-83)
Front Suspension & Differential
Drive Shaft Companion Flange20-22 (27-30)
Sub-Frame Mounting Bolts69-85 (94-115)

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 21 © 2005 Mitchell Repair Information Company, LLC.

1991 TORQUE SPECIFICATIONS (B2200 & B2600i)
1990 TORQUE SPECIFICATIONS (MIATA)
Splash Shield23-34 (31-46)
Rear Drive Axle
Axle Bearing Lock Nut145-217 (197-294)
Backing Plate Bolt
2WD72-87 (98-118)
4WD65-80 (88-109)
Drive Shaft Companion Flange20-22 (27-30)
Wheel Lug Nuts
Standard Wheel65-87 (88-118)
Styled Wheel87-108 (118-146)
ApplicationFt. Lbs. (N.m)
Brake Pipe Union10-16 (14-22)
Differential Carrier-To-Housing Nuts17-20 (23-27)
Differential Carrier Bearings Cap Bolts
"P" Series Differential41-59 (56-80)
"M" Series Differential27-38 (37-52)
Differential Carrier Bearings Lock Plate Bolt13-19 (18-26)
Drive Pinion Lock Nut94-210 (127-284)
Drive Shaft Companion Flange Nuts20-22 (27-30)
Filler Plug29-40 (39-54)
Front Subframe Mounting Bolts69-85 (94-115)
Rear Axle Bearing Lock Nut145-217 (197-294)
Rear Backing Plate Bolt
2WD72-87 (98-118)
4WD65-80 (88-109)
Ring Gear Retaining Bolts51-61 (69-83)
Splash Shield Bolts23-34 (31-46)
Wheel Lug Nuts
Standard Wheel65-87 (88-118)
Styled Wheel87-108 (118-146)
ApplicationFt. Lbs. (N.m)
Differential Assembly
Differential Carrier-to-Housing17-20 (23-27)
Differential Carrier Bearings Cap Bolts50-66 (68-90)
Differential Carrier Bearings Lock Tab14-19 (19-26)
Differential Case Rear Mounts
Drive Pinion Lock Nut87-130 (118-176)

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 22 © 2005 Mitchell Repair Information Company, LLC.

1991 TORQUE SPECIFICATIONS (MIATA)
1990 TORQUE SPECIFICATIONS (MPV 4WD)
Inner Nut61-72 (83-98)
Outer Nuts (2)13-20 (18-26)
Filler Plug29-40 (39-54)
Ring Gear Retaining Bolts51-61 (69-83)
Power Plant Frame-to-Differential Mounting
Spacer Bolt (Short)27-38 (37-52)
PPF-to-Differential Side Mounting Bolts (Long)77-91 (104-123)
PPF-to-PPF Bracket Bolt27-40 (37-54)
Power Plant Frame-to-Transmission
Side Mounting Bolts (Long)77-91 (104-123)
Transmission-to-PPF Bracket Bolts27-40 (37-54)
ApplicationFt. Lbs. (N.m)
Differential Carrier-To-Housing Nuts17-20 (23-27)
Differential Carrier Bearings Cap Bolts27-38 (37-52)
Differential Carrier Bearings Lock Plate Bolt13-19 (18-26)
Differential Case Rear Mount Nuts54-69 (73-94)
Drive Pinion Lock Nut87-130 (118-176)
Inner Nut61-72 (83-98)
Outer Nuts (2)13-20 (18-26)
Drive Shaft Companion Flange Nuts20-22 (27-30)
Filler Plug29-40 (39-54)
Ring Gear Retaining Bolts51-61 (69-83)
Power Plant Frame-To-Differential Mounting
Spacer Bolt (Short)27-38 (37-52)
PPF-To-Differential Bolts
Side Mounting Bolts (Long)77-91 (104-123)
PPF-To-PPF Bracket Bolt27-40 (37-54)
Power Plant Frame-To-Transmission
Side Mounting Bolts (Long)77-91 (104-123)
Transmission-To-PPF Bracket Bolts27-40 (37-54)
Wheel Lug Nuts65-87 (88-118)
ApplicationFt. Lbs. (N.m)
Brake Pipe Union10-16 (14-22)
Differential Assemblies
Differential Carrier Bearings Cap Bolts
Front Differential27-38 (37-52)
Rear Differential54-79 (73-107)

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 23 © 2005 Mitchell Repair Information Company, LLC.

1991 TORQUE SPECIFICATIONS (MPV)
1990 TORQUE SPECIFICATIONS (PROTEGE 4WD)
Differential Carrier Bearings Lock Tab13-19 (18-26)
Differential Carrier-to-Housing17-20 (23-27)
Drive Pinion Lock Nut94-210 (127-285)
Filler Plug29-40 (39-54)
Ring Gear Retaining Bolts51-61 (69-83)
Front Axle Components
Differential-to-Chassis Mounts49-72 (66-98)
Drive Shaft Companion Flange36-43 (49-58)
Extension Housing-to-Differential Housing27-40 (36-54)
Lower Ball Joint-to-"A" Frame75-101 (102-137)
Splash Shield12-17 (16-23)
Rear Axle Components
Axle Bearing Retainer Nuts72-87 (98-118)
Brake Drum Retaining Screws10-11 (14-15)
Drive Shaft Companion Flange36-43 (49-58)
ApplicationFt. Lbs. (N.m)
Brake Pipe Union10-16 (14-22)
Differential-To-Chassis Mount Nuts (4WD)49-72 (66-98)
Differential Carrier Bearings Cap Bolts
Front Differential27-38 (37-52)
Rear Differential54-79 (73-107)
Differential Carrier Bearings Lock Plate Bolt13-19 (18-26)
Differential Carrier-To-Housing Nuts17-20 (23-27)
Drive Pinion Lock Nut94-210 (127-285)
Drive Shaft Companion Flange Nuts36-43 (49-58)
Filler Plug29-40 (39-54)
Lower Ball Joint-To-Control Arm Bolts (4WD)75-101 (102-137)
Lower Ball Joint-To-Control Arm Nut (4WD)94-127 (128-172)
Rear Axle Bearing Retainer Nuts72-87 (98-118)
Rear Brake Drum Retaining Screws7-11 (10-15)
RFW Extension Housing Mount Nut (4WD)149-72 (66-98)
Ring Gear Retaining Bolts51-61 (69-83)
Splash Shield Bolts (4WD)12-17 (16-23)
Tie Rod End Nut (4WD)43-58 (59-78)
Wheel Lug Nuts65-87 (88-118)
ApplicationFt. Lbs. (N.m)
Differential Assembly

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 24 © 2005 Mitchell Repair Information Company, LLC.