differential MAZDA MIATA 1991 Factory Owner's Guide

1991 TORQUE SPECIFICATIONS (PROTEGE 4WD)
1990-91 TORQUE SPECIFICATIONS (RX7)
Differential Carrier Bearing Cap Bolts27-38 (37-52)
Differential Carrier Bearing Lock Tab14-19 (19-26)
Differential Carrier-to-Housing17-20 (23-27)
Differential Case
Front Mounts33-50 (45-68)
Rear Mounts80-97 (109-132)
Drive Pinion Lock Nut87-130 (118-176)
Filler Plug29-40 (39-54)
Ring Gear Retaining Bolts51-61 (69-83)
Suspension & Mounts
Drive Axle Inner CV Joint Nut40-47 (54-64)
Drive Shaft Companion Flange20-22 (27-30)
Front Mount33-50 (45-68)
Lateral Link46-55 (62-75)
Rear Mount80-97 (109-132)
Stabilizer Bar10-13 (14-18)
Trailing Link69-86 (94-117)
Wheel Lug Nuts65-87 (88-118)
ApplicationFt. Lbs. (N.m)
Differential Carrier Bearing Cap Bolts27-38 (37-52)
Differential Carrier Bearing Lock Plate Bolt13-19 (18-26)
Differential Carrier-To-Housing Nuts17-20 (23-27)
Differential Case
Front Mounts39-47 (53-63)
Rear Mounts68-86 (93-116)
Drive Axle Inner CV Joint Nut40-47 (54-64)
Drive Pinion Lock Nut87-130 (118-176)
Drive Shaft Companion Flange Nuts20-22 (27-30)
Filler Plug29-40 (39-54)
Lateral Link Bolts46-55 (62-75)
Ring Gear Retaining Bolts51-61 (69-83)
Stabilizer Bar Bolts31-43 (43-58)
Trailing Link Bolts68-93 (93-126)
Wheel Lug Nuts65-87 (88-118)
ApplicationFt. Lbs. (N.m)
Differential Carrier-to-Housing17-20 (23-27)
Differential Carrier

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 25 © 2005 Mitchell Repair Information Company, LLC.

1990-91 TORQUE SPECIFICATIONS (929)
Bearing Cap Bolts (1) 54-79 (73-107)
Differential Carrier Bearing Cap Bolts (2) 50-66 (73-107)
Differential Carrier Bearing Lock Tab13-19 (18-26)
Differential Case Front Hanger Nut65-77 (88-104)
Differential Case Rear Mounts54-69 (73-94)
Differential Ring Gear Bolts51-61 (69-83)
Drive Axle Inner CV Joint Nut40-47 (54-64)
Drive Pinion Lock Nut94-210 (127-285)
Drive Shaft Companion Flange36-43 (49-58)
Filler Plug29-40 (39-54)
Ring Gear Retaining Bolts51-61 (69-83)
Support Strut Mounting Bolt54-69 (73-94)
Wheel Lug Nuts65-87 (88-118)
(1)1990 Model.
(2)1991 Model.
ApplicationFt. Lbs. (N.m)
ABS Sensor-to-Hub Support Bolt12-17 (16-23)
Differential Carrier Bearing
Cap Bolts50-66 (68-90)
Lock Tabs13-18 (18-24)
Differential Carrier-to-Housing17-20 (23-27)
Differential Case
Front Hanger Nut69-86 (94-117)
Rear Mounts69-86 (94-117)
Drive Axle Inner CV Joint Nut40-47 (54-64)
Drive Pinion Lock Nut94-130 (127-176)
Drive Shaft Companion Flange Bolts36-43 (49-58)
Filler Plug29-40 (39-54)
Ring Gear Retaining Bolts51-61 (69-83)
Wheel Lug Nuts65-87 (88-118)

1991 Mazda MX-5 Miata
1990-91 DRIVE AXLES Differentials & Drive Axles - 929, B2200, B2600i, MX-5 Miata, MPV, Protege & RX-7
Microsoft
Sunday, July 05, 2009 2:17:01 PMPage 26 © 2005 Mitchell Repair Information Company, LLC.

to field coil housing. If continuity exists, repair or replace field coil.
OVERRUNNING CLUTCH PINION DRIVE
Hold overrunning clutch housing and turn pinion gear by hand. If pinion turns in both directions, clutch is faulty
and must be replaced. DO NOT clean overrunning clutch with solvent, as it is packed with grease and sealed by
manufacturer.
REMOVAL & INSTALLATION
1. Disconnect negative battery cable. Raise vehicle on hoist. Remove undercover. Disconnect wiring from
starter. Remove differential lock assembly (4WD models). On Protege (M/T) and 323 models, remove
support brace from under intake manifold. Remove starter mounting bolts. Remove lowest mounting bolt
last. Remove starter from under side of vehicle.
2. To install starter, reverse removal procedure. Tighten mounting bolts to 23-24 ft. lbs. (31-46 N.m).
Tighten battery terminal nut to 87-104 INCH lbs. (9.8-12 N.m).
OVERHAUL
DISASSEMBLY & ASSEMBLY
1. Mark rear cover, field coil housing and front drive housing for reassembly reference. Remove solenoid
and shims, rear cover and brush plate. Remove field coil housing and pull armature and yoke lever from
front drive housing. See Fig. 4
& Fig. 5. Use arbor press to remove circlip, stopper and pinion drive from
armature shaft. See Fig. 6
.
2. To assemble, reverse removal procedures. Lubricate solenoid plunger, yoke lever and armature bushings.
Use arbor press and pinion drive to install stopper and circlip on armature shaft. See Fig. 6
. Ensure brush
plate, rear cover and field coil housin
g are aligned when installing through bolts.

1991 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive
Microsoft
Sunday, July 05, 2009 2:13:20 PMPage 8 © 2005 Mitchell Repair Information Company, LLC.