electrical MAZDA MIATA 1991 Factory Owner's Guide

Fig. 3: Adjusting Pinion Gap
Courtesy of MAZDA MOTORS CORP.
BENCH TESTING (DISASSEMBLED)

1991 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive
Microsoft
Sunday, July 05, 2009 2:13:20 PMPage 6 © 2005 Mitchell Repair Information Company, LLC.

ARMATURE TESTING
1. Place armature in growler. Turn on growler and hold a piece of hacksaw blade over armature. Slowly
rotate armature. If hacksaw blade is attracted to core or if it vibrates, replace armature.
2. Remove armature from growler. Using an ohmmeter, check continuity between commutator and core. If
continuity exists, the armature is shorted and must be replaced. Check continuity between commutator
and shaft. If continuity exists, replace armature.
3. Check continuity between each commutator segment. If an open exists between any 2 segments, replace
armature.
COMMUTATOR TESTING
1. Clean surface and polish with No. 400 sandpaper if required. If surface is scored, out of round or pitted,
turn commutator in a lathe.
2. Maximum commutator runout and minimum diameter of commutator must not exceed specification after
turning. See COMMUTATOR SPECIFICATIONS table.
3. Commutator mica undercut depth should be .02 -.03" (.5 -.8 mm). Minimum mica undercut depth
is .008" (.20 mm). If not within specification, undercut to standard depth.
COMMUTATOR SPECIFICATIONS
BRUSH TESTING
1. Connect ohmmeter lead to positive brush holder and other lead to negative brush holder. If continuity
exists, brush holder assembly is shorted and must be replaced.
2. Check brush length. If less than specification, replace brushes. See BRUSH LENGTH
SPECIFICATIONS table. Use brush spring scale to check spring tension. Spring tension is measured at
point where spring separates from brush.Tension should be greater than 2 lbs. (0.9 kg). Tension
specification for a new spring is 3.1-5.7 lbs. (1.4-2.6 kg). Brushes must move freely in holders.
BRUSH LENGTH SPECIFICATIONS
FIELD COIL TESTING
1. Connect one ohmmeter lead to field coil lead ("M" terminal lead). Connect other lead to soldered portion
of brush lead. If continuity does not exist, repair or replace field coil.
2. Check field coil for shorts to
ground by connecting ohmmeter lead to field coil lead. Connect other lead
Application
Maximum Runout In.
(mm)Minimum Diameter
In. (mm)
B2200 (M/T)
Protege (M/T) & 323.004 (.10)1.22 (31)
Miata.001 (.03)1.22 (31)
ApplicationStandard In. (mm)Minimum In. (mm)
All Models.67 (17.0).45 (11.5)

1991 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive
Microsoft
Sunday, July 05, 2009 2:13:20 PMPage 7 © 2005 Mitchell Repair Information Company, LLC.

to field coil housing. If continuity exists, repair or replace field coil.
OVERRUNNING CLUTCH PINION DRIVE
Hold overrunning clutch housing and turn pinion gear by hand. If pinion turns in both directions, clutch is faulty
and must be replaced. DO NOT clean overrunning clutch with solvent, as it is packed with grease and sealed by
manufacturer.
REMOVAL & INSTALLATION
1. Disconnect negative battery cable. Raise vehicle on hoist. Remove undercover. Disconnect wiring from
starter. Remove differential lock assembly (4WD models). On Protege (M/T) and 323 models, remove
support brace from under intake manifold. Remove starter mounting bolts. Remove lowest mounting bolt
last. Remove starter from under side of vehicle.
2. To install starter, reverse removal procedure. Tighten mounting bolts to 23-24 ft. lbs. (31-46 N.m).
Tighten battery terminal nut to 87-104 INCH lbs. (9.8-12 N.m).
OVERHAUL
DISASSEMBLY & ASSEMBLY
1. Mark rear cover, field coil housing and front drive housing for reassembly reference. Remove solenoid
and shims, rear cover and brush plate. Remove field coil housing and pull armature and yoke lever from
front drive housing. See Fig. 4
& Fig. 5. Use arbor press to remove circlip, stopper and pinion drive from
armature shaft. See Fig. 6
.
2. To assemble, reverse removal procedures. Lubricate solenoid plunger, yoke lever and armature bushings.
Use arbor press and pinion drive to install stopper and circlip on armature shaft. See Fig. 6
. Ensure brush
plate, rear cover and field coil housin
g are aligned when installing through bolts.

1991 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive
Microsoft
Sunday, July 05, 2009 2:13:20 PMPage 8 © 2005 Mitchell Repair Information Company, LLC.

Fig. 4: View of Direct Drive Starters (Miata, Protege, 323 & MX-3)
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive
Microsoft
Sunday, July 05, 2009 2:13:20 PMPage 9 © 2005 Mitchell Repair Information Company, LLC.

Fig. 5: Exploded View of Direct Drive Starters (B2200)
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive
Microsoft
Sunday, July 05, 2009 2:13:20 PMPage 10 © 2005 Mitchell Repair Information Company, LLC.

Fig. 6: Removing & Installing Armature Circlip & Stopper
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive
Microsoft
Sunday, July 05, 2009 2:13:20 PMPage 11 © 2005 Mitchell Repair Information Company, LLC.