ABS MAZDA MODEL 3 HATCHBACK 2015 (in English) User Guide

4–174
When Driving
Rear View Monitor
Picture Quality Adjustment
WARNING
Always adjust the picture quality of the rear view monitor while the vehicle is stopped:
Do not adjust the picture quality of the rear view monitor while driving the vehicle.
Adjusting the picture quality of the rear view monitor such as brightness, contrast,
colour, and tint while driving the vehicle is dangerous as it could distract your attention
from the vehicle operation which could lead to an accident.
Picture quality adjustment can be done while the shift lever is in reverse (R).
There are four settings which can be adjusted including, brightness, contrast, tint, and
colour. When adjusting, pay suffi cient attention to the vehicle surroundings.
1. Select the
icon on the screen to display the tabs.
2. Select the desired tab item.
3. Adjust the brightness, contrast, tint, and colour using the slider.
If you need to reset, press the reset button.
4. Select the
icon on the screen to close the tab.
.B[EB@&'&&"@&EJUJPOJOEC







4–176
When Driving
Parking Sensor System
NOTE
  Do not install any accessories within the detection ranges of the sensors. It may affect
the system operation.
  Depending on the type of obstruction and the surrounding conditions, the detection
range of a sensor may narrow, or the sensors may not be able to detect obstructions.
  The system may not operate normally under the following conditions:




 Mud, ice, or snow is adhering to the sensor area (Returns to normal operation when
removed).
 


 The sensor area is frozen (Returns to normal operation when the ice is thawed).



 The sensor is covered by a hand.



 The sensor is excessively shocked.



 The vehicle is excessively tilted.



 Under extremely hot or cold weather conditions.



 The vehicle is driven on bumps, inclines, gravel, or grass covered roads.



 Anything which generates ultrasound is near the vehicle, such as another vehicle's
horn, the engine sound of a motorcycle, the air brake sound of a large-sized vehicle,
or another vehicle's sensors.
 


 The vehicle is driven in heavy rain or in road conditions causing water-splash.



 A commercially-available wing pole or an aerial for a radio transmitter is installed to
the vehicle.
 


 The vehicle is moving towards a tall or square curbstone.



 An obstruction is too close to the sensor. 

 Obstructions under the bumper may not be detected. Obstructions that are lower than
the bumper or thin which may have been initially detected but are no longer detected
as the vehicle approaches more closely.
  The following types of obstructions may not be detected:




 Thin objects such as wire or rope



 Things which absorb sonic waves easily such as cotton or snow



 Angular shaped objects



 Very tall objects, and those which are wide at the top



 Small, short objects 

 Always have the system inspected at an expert repairer, we recommend an Authorised
Mazda Repairer if any shock is applied to the bumpers, even in a minor accident. If the
sensors are deviated, they cannot detect obstructions.
 (With front sensor and front corner sensor) The system may have a malfunction if the beep does not operate or the indicator light
does not illuminate when the park assist sensors switch is turned on. Consult an expert
repairer, we recommend an Authorised Mazda Repairer.
 (Without front sensor and front corner sensor) The system may have a malfunction if the beep does not operate. Consult an expert
repairer, we recommend an Authorised Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC







5–70
Interior Features
Audio System
NOTE
  For safety reasons, images are not
displayed while the vehicle is being
driven.
  Slide the of the controller to
move the controller.
  If the mode is switched to DVD
mode once the DVD playback
has stopped, the playback restarts
without displaying the DVD menu
screen.
Setting DVD functions
Sound quality and aspect ratio settings can
be performed.
Setting sound quality
1. Select the
icon.
2. Select
to adjust the sound
quality.
Refer to Volume/Display/Sound
Controls on page 5-54 .
Setting aspect ratio
1. Select the
icon.
2. Select
.
3. Select a desired aspect ratio.
Setting image quality
Brightness, contrast, tint, colour density
can be adjusted.
When the
icon is selected, the following
tabs are displayed at the bottom of the
screen.
Tab Function
Screen brightness can be
adjusted using the slider.
Screen contrast can be
adjusted using the slider.
Colour tone of the screen
can be adjusted using the
slider.
Screen colour can be
adjusted using the slider.
Screen settings can be reset
to initial values.
Select
.
How to use Auxiliary jack/USB
port
Audio can be heard from the vehicle's
speakers by connecting a commercially-
available portable audio unit to the
auxiliary jack.
Use a commercially-available, non-
impedance (3.5
) stereo mini plug lead.
In addition, audio can be played from the
vehicle audio device by connecting a USB
device or an iPod to the USB port.
Refer to AUX/USB/iPod mode on page
5-75 .
.B[EB@&'&&"@&EJUJPOJOEC







6–59
Maintenance and Care
Owner Maintenance
Brake lights/Tail lights (Bulb type)
5. Install the new bulb in the reverse order
of the removal procedure.
6. Insert the cover tabs and install the
cover.
Tabs
NOTE
Verify that the cover is securely
installed.(Right side)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the knob and remove the cover.
3. Turn the wing bolt and jack screw
anticlockwise.
4. Remove the jack
5. Turn the socket and bulb assembly
anticlockwise and remove it.
.B[EB@&'&&"@&EJUJPOJOEC







6–60
Maintenance and Care
Owner Maintenance
6. Disconnect the bulb from the socket.
Rear direction indicator lights
Brake lights/Tail lights (Bulb type)
7. Install the new bulb.
8. Insert the wing bolt into the jack with
the jack screw pointing to the down
and turn the wing bolt clockwise to
temporarily tighten it.9. Turn the jack screw in the direction
shown in the fi gure.
10. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suffi ciently tightened.
11. Install the cover in the reverse order of
the removal procedure.
12. Insert the cover tabs and install the
cover.
Tabs
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–68
Maintenance and Care
Owner Maintenance
Fuse Panel Description
Fuse block (Engine compartment)
Multiplex slow blow fuse
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 FOG 15 A Front fog lights
*
2 H/L HI 20 A Headlight high beam
3 H/CLEAN 20 A Headlight washer *
4 STOP 10 A Brake lights, Rear fog light *
5 ROOM 15 A Overhead light
6
7.5 A Engine control system *
7 FUEL WARM 15 A Fuel warmer *
8 HAZARD 25 A Hazard warning fl ashers, Direction indicator lights
9 ABS/DSCS 30 A ABS, Dynamic stability control system *
10 METER2 7.5 A Instrument cluster *
11 AUDIO2 7.5 A Audio system *
12 BOSE 25 A Bose ® Sound System-equipped model *
13 AUDIO1 15 A Audio system *
14 FUEL PUMP 15 A Fuel system *
15 HID R
D R L 15 A Headlight (RH) *1
16 AT PUMP 15 A Transaxle control system *
17 HORN 15 A Horn
18 TAIL 15 A Tail lights, Number plate lights, Position lights
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–70
Maintenance and Care
Owner Maintenance
Fuse block (Left side)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 P.WINDOW3
P.SEAT D 30 A Power seat
*
2 D.LOCK 25 A Power door locks
3 P.WINDOW2 25 A Power windows
4 SEAT WARM 20 A Seat warmer
*
5 R.OUTLET3 15 A —
6 SRS2/ESCL 15 A Electronic steering lock
7 SUNROOF 10 A Sunroof
*
8 M.DEF 7.5 A Mirror defogger *
9 R.OUTLET1 15 A Accessory sockets *
10 MIRROR 7.5 A Power control mirror
11 F.OUTLET 15 A Accessory sockets
12 ABS IG
AT IND 7.5 A AT shift indicator
*
13 SRS1 7.5 A —
14 METER1 10 A —
15 C/U IG1 15 A —
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–5
If Trouble Arises
Flat Tyre
Jack *
NOTE
Your vehicle may or may not be
equipped with a jack and wheel brace.
For details, consult an Authorised
Mazda Dealer.
To remove the jack
1 . (Saloon)
Push the tabs and remove the cover.
Tabs
(Hatchback)
Turn the knob and remove the cover.
2. Turn the wing bolt and jack screw
anticlockwise.
To secure the jack
1. Insert the wing bolt into the jack with
the jack screw pointing to the down
and turn the wing bolt clockwise to
temporarily tighten it.
2. Turn the jack screw in the direction
shown in the fi gure.
3. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suffi ciently tightened.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–6
If Trouble Arises
Flat Tyre
4. Insert the cover tabs and install the
cover.
(Saloon)
Tabs
Tabs (Hatchback)
NOTE
Verify that the cover is securely
installed.
Maintenance
 




 Always keep the jack clean.



 Make sure the moving parts are kept
free from dirt or rust.
 


 Make sure the screw thread is
adequately lubricated.
Spare Tyre *
Your Mazda has a temporary spare tyre.
The temporary spare tyre is lighter and
smaller than a conventional tyre, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spare tyres should
NEVER be used for long drives or
extended periods.
WARNING
Do not install the temporary spare tyre
on the front wheels (driving wheels):
Driving with the temporary spare tyre
on one of the front driving wheels is
dangerous. Handling will be affected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tyre to the front wheel and install the
temporary spare tyre to the rear.
.B[EB@&'&&"@&EJUJPOJOEC







7–11
If Trouble Arises
Flat Tyre
9. Remove the valve cap from the valve
of the fl at tyre, install the injection hose
to the tyre valve, turn the sleeve to the
right, and tighten it.
Valve cap Valve Injection hose
10. Install the bottle to the air compressor
and press it in until the left and right
tabs are engaged securely.
Tabs
11. Insert the air compressor plug into the
accessory socket inside the vehicle and
switch the ignition to ACC.
Refer to Accessory Sockets on page
5-155 .
Centre console
Compressor
Compressor plug
CAUTION
When inserting the air compressor
plug into or removing it from the
accessory socket, make sure that the air
compressor switch is OFF. When turning
the air compressor ON/OFF, use the air
compressor switch.
12. The sealant is injected into the tyre
when the air compressor is switched
ON. After the sealant is injected
completely, wait until the tyre infl ation
pressure increases to the specifi ed tyre
infl ation pressure.
NOTE
The infl ation pressure may increase
to about 300 kPa (3.1 kgf/cm 2 , 3 bar,
43.5 psi) temporarily to inject the
sealant through the valve. Normally, the
infl ation pressure decreases gradually
and it reaches the actual infl ation
pressure after about 30 seconds.
.B[EB@&'&&"@&EJUJPOJOEC