turn signal MAZDA MODEL CX-3 2016 (in English) User Guide

*Some models.4–45
When Driving
Switches and Controls
NOTE




y The time until the headlights turn off
after all of the doors are closed can be
changed.
  Refer to Personalization Features on
page 9-10 .
 


y If no operations are done for 3 minutes
after the lever is pulled, the headlights
turn off.
 


y The headlights turn off if the lever is
pulled again while the headlights are
illuminated.
Leaving Home Light System
The leaving home light system turns on
the lights when the transmitter unlock
button is pressed while away from the
vehicle.
To turn on the system
When the ignition switch and the
headlight switch are as indicated below,
the headlights will illuminate when the
transmitter unlock button is pressed and
the vehicle receives the transmitter signal.
The headlights turn off after a certain
period of time has elapsed (30 seconds).
 


y Ignition switch: off



y Headlight switch: or
The following lights turn on when the
leaving home light system is operated.
Low beams, Parking lights, Taillights,
License lights
Unlock button
Lock button
NOTE
 


y Operation of the leaving home light
system can be turned on or off.
  Refer to Personalization Features on
page 9-10 .
 


y When the transmitter lock button is
pressed and the vehicle receives the
transmitter signal, the headlights turn
off.
 


y When the headlight switch is in a
position other than
or , the
headlights turn off.
Headlight Leveling *
The number of passengers and weight of
cargo in the luggage compartment change
the angle of the headlights.
The angle of the headlights will be
automatically adjusted when turning on
the headlights.
Daytime Running Lights
Some countries require moving vehicles
to have their lights on (daytime running
lights) during the daytime.
The daytime running lights turn on
automatically when the vehicle starts
moving.
They turn off when the parking brake is
operated or the shift lever is shifted to the
P position .
NOTE
(Except Canada)
The daytime running lights can be
deactivated.
Refer to Personalization Features on page
9-10 .
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










*Some models.4–46
When Driving
Switches and Controls
Fog Lights *
The fog lights can be used when the
ignition is switched ON.
Use this switch to turn on the fog lights.
The fog lights will improve visibility at
night and during foggy conditions.
The fog lights turn on when the fog light
switch is turned to the
position and turn
off when the switch is turned to the
position.
The fog lights turn on when the headlights
are turned on. They will not turn on if the
headlight switch is in the
position or
position.
Fog light switch
NOTE
 y  The fog lights will turn off when the
headlights are set at high beams.

y(With auto-light control) If the fog light switch is in the
position and the headlight switch is in
the
position, the fog lights will
turn on when the headlights, the
exterior lights and dashboard
illumination turn on.
Turn and Lane-Change
Signals
The ignition must be switched ON to use
the turn and lane-change signals.
Turn Signals
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to fl ash
after a turn, manually return the lever to its
original position.
Right turn
Left turn
Right lane change
Left lane change OFF
The turn signal indicators (green) in the
instrument cluster fl
ash according to the
operation of the turn signal lever to show
which signal is working.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–47
When Driving
Switches and Controls
NOTE
 


y If an indicator light stays on without
fl ashing or if it fl ashes abnormally, one
of the turn signal bulbs may be burned
out.
 


y A personalized function is available to
change the turn indicator sound volume.
(page 9-10 )
Lane-Change Signals
Move the lever halfway toward the
direction of the lane change—until the
indicator fl ashes— and hold it there. It will
return to the off position when released.
Three-Flash Turn Signal
After releasing the turn signal lever, the
turn signal indicator fl ashes three times.
The operation can be cancelled by moving
the lever in the direction opposite to which
it was operated.
NOTE
The three-fl ash turn signal function can be
switched to operable/inoperable using the
personalization function.
Refer to Personalization Features on page
9-10 .
Windshield Wipers and
Washer
The ignition must be switched ON to use
the wipers.
WARNING
Use only windshield washer fl uid or
plain water in the reservoir:
Using radiator antifreeze as washer
fl uid is dangerous. If sprayed on the
windshield, it will dirty the windshield,
aff ect your visibility, and could result in
an accident.

Only use windshield washer fl uid mixed
with anti-freeze protection in freezing
weather conditions:
Using windshield washer fl uid without
anti-freeze protection in freezing
weather conditions is dangerous as
it could freeze on the windshield and
block your vision which could cause
an accident. In addition, make sure
the windshield is suffi ciently warmed
using the defroster before spraying the
washer fl uid.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–53
When Driving
Switches and Controls
Horn
To sound the horn, press the mark on
the steering wheel.
Hazard Warning Flasher
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffi c hazard
and that they must take extreme caution
when near it.
Depress the hazard warning fl asher and
all the turn signals will fl ash. The hazard
warning indicator lights in the instrument
cluster fl ash simultaneously.
NOTE




y The turn signals do not work when the
hazard warning lights are on.
 


y Check local regulations about the use of
hazard warning lights while the vehicle
is being towed to verify that it is not in
violation of the law.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–72
When Driving
i-ACTIVSENSE
NOTE
The timing in which the system switches the headlights changes under the\
following
conditions. If the system does not switch the headlights appropriately, manually switch
between high and low beams according to the visibility as well as road and traffi c
conditions.
 y When there are sources of light in the area such as street lamps, illuminated signboards,
and traffi c signals.

y When there are refl ective objects in the surrounding area such as refl ective plates and
signs.

y  When visibility is reduced under rain, snow and foggy conditions.
y When driving on roads with sharp turn or hilly terrain.
y When the headlights/rear lamps of vehicles in front of you or in the opposite lane are dim
or not illuminated.

y When there is suffi cient darkness such as at dawn or dusk.
y When the luggage compartment is loaded with heavy objects or the rear passenger seats
are occupied.

y When visibility is reduced due to a vehicle in front of you spraying water from its tires
onto your windshield.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–75
When Driving
i-ACTIVSENSE
CAUTION
Do not modify the suspension. If the vehicle height or the damping force of the
suspensions is changed, the LDWS may not operate correctly.
NOTE
 


y If your vehicle deviates from its traffi c lane, the LDWS operates (warning sound and
indicator light). Steer the vehicle adequately to drive the vehicle to the center of the lane.
 


y When the turn signal lever is operated for a lane change, the LDWS warning is
automatically canceled. The LDWS warning becomes operable when the turn signal lever
is returned and the system detects the white or yellow lines.
 


y If the steering wheel, accelerator pedal, or brake pedal is operated abruptly and the
vehicle moves close to a white or yellow line, the system determines that the driver is
making a lane change and the LDWS warning is automatically canceled.
 


y The LDWS may not operate during the period immediately after the vehicle has deviated
from its lane and the LDWS has operated, or the vehicle deviates from its lane repeatedly
within a short period of time.
 


y The LDWS does not operate if it does not detect the white or yellow lines of the traffi c
lane.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–78
When Driving
i-ACTIVSENSE
NOTE
 


y The LDWS does not operate until the
system detects a white or yellow line on
either the left or right.
 


y When the system detects a white or
yellow line on one side only, the system
will activate the warning only when the
vehicle deviates on the side where the
white or yellow line is being detected.
 


y The distance and warning sensitivity
(likelihood of a warning) which the
system uses to determine the possibility
of a lane departure can be changed.
  Refer to Personalization Features on
page 9-10 .
Auto cancel
In the following cases, the LDWS cancels
automatically and the LDWS warning
light in the instrument cluster turns on.
 


y The temperature inside the camera is
high or low.
 


y The windshield around the camera is
foggy.
 


y The windshield around the camera is
blocked by an obstruction, causing poor
forward visibility.
For vehicles equipped with the active
driving display, the lane (border lines) is
indicated in the display. The LDWS is
enabled automatically when the operation
conditions are met, and the LDWS
warning light turns off.
Auto cancel warning
When the following operations are
performed, the LDWS determines that
the driver intends to make a lane change
and the LDWS warning is canceled
automatically. The LDWS is enabled
automatically after the driver performs the
operation.
 


y The steering wheel is operated abruptly.



y The brake pedal is depressed abruptly.



y The accelerator pedal is depressed
abruptly.
 


y The turn signal lever is operated (after
the turn signal lever is returned, the
LDWS may not operate for about 3
seconds which is the period of time
required to make a lane correction).
NOTE
After about 60 seconds have elapsed with
the turn signal lever left operating, the
LDWS warning may operate if the vehicle
is close to a white or yellow line.
Canceling the System
Press the LDWS switch to cancel the
LDWS. The LDWS OFF indicator light
turns on.
For vehicles with the active driving
display, the driving lane indication in the
active driving display is not indicated
when the LDWS is cancelled.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










*Some models.4–80
When Driving
i-ACTIVSENSE
Blind Spot Monitoring (BSM) System *
The Blind Spot Monitoring (BSM) system is designed to assist the driver in checking the
area to the rear of the vehicle on both sides during lane changes by alerting the driver to the
presence of vehicles approaching from the rear in an adjacent lane.
The Blind Spot Monitoring (BSM) system detects vehicles approaching from the rear while
traveling in the forward direction at a speed of 10 km/h (6.3 mph) or faster and turns on the
Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors depending on
the conditions. If the turn signal lever is operated to signal a lane change in the direction
in which the Blind Spot Monitoring (BSM) warning light is illuminated, the system warns
the driver of a vehicle in the detection area by fl ashing the Blind Spot Monitoring (BSM)
warning light and activating a beep sound.
The detection area on this system covers the driving lanes on both sides of the vehicle and
from the rear part of the front doors to about 50 m (164 ft) behind the vehicle.
Detection areas Your vehicle
WARNING
Always check the surrounding area visually before making an actual lane change:
The system is only designed to assist you in checking for vehicles at your rear when
making a lane change. Due to certain limitations with the operation of this system, the
Blind Spot Monitoring (BSM) warning light may not fl ash or it might be delayed even
though a vehicle is in an adjacent driving lane. Always make it your responsibility as a
driver to check the rear.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–84
When Driving
i-ACTIVSENSE
Forward driving (Blind Spot Monitoring (BSM) system operation)
The Blind Spot Monitoring (BSM) system detects vehicles approaching from the rear and
turns on the Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors
according to the conditions. Additionally, while a Blind Spot Monitoring (BSM) warning
light is illuminated, if the turn signal lever is operated to signal a turn in the direction
in which the Blind Spot Monitoring (BSM) warning light is illuminated, the Blind Spot
Monitoring (BSM) warning light fl ashes.
Reverse driving (Rear Cross Traffi c Alert (RCTA) system operation)
The Rear Cross Traffi c Alert (RCTA) system detects vehicles approaching from the left and
right of your vehicle and fl ashes the Blind Spot Monitoring (BSM) warning lights.
Function for cancelling illumination dimmer
When the headlight switch is in the
or position, the brightness of the Blind Spot
Monitoring (BSM) warning lights is dimmed.
If the Blind Spot Monitoring (BSM) warning lights are diffi cult to see due to glare from
surrounding brightness when traveling on snow-covered roads or under foggy conditions,
press the dimmer cancellation button to cancel the dimmer and increase the brightness of
Blind Spot Monitoring (BSM) warning lights when they turn on.
Refer to Dashboard Illumination on page 4-18 .
Blind Spot Monitoring (BSM) warning beep
The Blind Spot Monitoring (BSM) warning beep is activated simultaneously with the
fl ashing of a Blind Spot Monitoring (BSM) warning light.
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC










4–110
When Driving
i-ACTIVSENSE
NOTE
 


y The Smart Brake Support (SBS) system operates when all of the following conditions are
met:
 


y The ignition is switched ON.



y The Smart Brake Support (SBS) system is on.



y The vehicle speed is about 15 km/h or faster (10 mph or faster).



y The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
 


y The Dynamic Stability Control (DSC) is not operating.




y The Smart Brake Support (SBS) system may not operate under the following conditions:




y If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.



y The vehicle is driven at the same speed as the vehicle ahead.



y The accelerator pedal is depressed.



y The brake pedal is depressed.



y The steering wheel is being operated.



y The selector lever is being operated.



y The turn signal is being used.



y When the vehicle ahead is not equipped with taillights or the taillights are turned off.



y When warnings and messages, such as a dirty windshield, related to the Forward
Sensing Camera (FSC)/laser sensor (front) are being displayed in the center display.
 


y Although the objects which activate the system are four-wheeled vehicles, the radar
sensor (front) could detect the following objects, determine them to be an obstruction, and
operate the Smart Brake Support (SBS) system.
 


y Objects on the road at the entrance to a curve (including guardrails and snow banks).



y A vehicle appears in the opposite lane while cornering or rounding a curve.



y When crossing a narrow bridge.



y When passing under a low gate or through a tunnel or narrow gate.



y When entering an underground parking area.



y Metal objects, bumps, or protruding objects on the road.



y If you suddenly come close to a vehicle ahead.



y When driving in areas where there is high grass or forage.



y Two-wheeled vehicles such as motorbikes or bicycles.



y Pedestrians or non-metallic objects such as standing trees.




y When the system operates, the user is notifi ed by the fl ashing Smart Brake Support (SBS)
indicator light (red) and the active driving display.
 


y The Smart Brake Support (SBS) warning light (amber) turns on when the system has a
malfunction. Refer to Warning/Indicator Lights on page 4-24 .
$9@&)&"#@&EJUJPOJOEC


$9@&)&"#@&EJUJPOJOEC