reset MAZDA MODEL CX-5 2017 - RHD (UK, Australia) (in English) User Guide

NOTE
•If any of the INFO switch is pressed
while a message is displayed, it will no
longer be displayed the next time the
ignition is switched ON.
•After the vehicle is serviced and the
remaining time/distance is reset, the
message for the next maintenance
period will be displayed when the
remaining distance or time to the next
maintenance period approaches 0
(displays when engine is started).
•If there are multiple messages, they are
displayed according to their order.
•If OFF is set for Messages, messages
are not displayed.
▼Blind Spot Monitoring (BSM)
Display
Displays the system status.

Refer to Blind Spot Monitoring (BSM) on
page 4-115.
▼Distance Recognition Support
System (DRSS) Display*
Displays the distance between your
vehicle and the vehicle ahead.

Refer to Distance Recognition Support
System (DRSS) on page 4-127.
▼Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) Display
*
Displays the currently set system status.

Refer to Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop &
Go function) on page 4-149.
▼Mazda Radar Cruise Control
(MRCC) Display*
Displays the currently set system status.

Refer to Mazda Radar Cruise Control
(MRCC) on page 4-137.
When Driving
Instrument Cluster and Display
*Some models.4-37
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Lane-keep Assist System (LAS) &
Lane Departure Warning System
(LDWS) Display
*
Displays the system status.

Refer to Lane-keep A
ssist System (LAS)
& Lane Departure Warning System
(LDWS) on page 4-163.
▼ Cruise Control Set Vehicle Speed
Display*
The vehicle speed preset using the cruise
control is displayed.

Refer to Cruise Con
trol on page 4-207.
▼Adjustable Speed Limiter (ASL)
Display*
The setting status of the Adjustable Speed
Limiter (ASL) is displayed.

Refer to Adjustable
Speed Limiter (ASL)
on page 4-174.
▼ Vehicle Speed Alarm*
In this mode, the curr
ent setting for the
vehicle speed alarm is displayed. You can
change the vehicle speed setting at which
the warning is triggered.
NOTE
The vehicle speed alarm display is
activated at the same time the beep sound
is heard. The set vehicle speed flashes
several times.
The vehicle speed alarm can be set using
the centre display.
NOTE
•Always set the vehicle speed according
to the laws and regulations of the
country/city in which the vehicle is
driven. In addition, always verify the
speed of the vehicle using the
speedometer.
•The vehicle speed alarm function can be
set between 30 and 250 km/h (20 and
150 mph).
▼ Warning (Display Indication)
A message is displayed to notify the user
of the system operation status and
malfunctions or abnormalities.
If the warning light
turns on/flashes
simultaneously or a symbol is indicated in
the display, check the information
regarding the warning light or symbol.
(page 4-42)
When only a message is displayed, refer to
Message Indicated i n Multi-information
Display. (page 7-59)
When Driving
Instrument Cluster and Display
4-38*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•Cruise Control Operation Conditions
Refer to Cruise Control on page 4-207.
•Navigation Guidance (vehicles with navigation system)
•Speed limit indicator (vehicles with navigation system)
•Vehicle Speed
Each setting/adjustment for the active driving display can be p erformed on the centre
display.
1. Select the
icon on the home screen and display the Settings screen.
2. Select the AD-Disp tab.
3. Select the desired item and perform the setting/adjustment.
•Method for adjusting screen brightness (automatically/manually)
•Screen brightness initial settings (automatic adjustment is sel ected)
•Screen brightness adjustment (manual adjustment is selected)
•Display position of active driving display (display height)
•Active driving display angle adjustment (display angle correcti on) (With windscreen
type)
•Active driving display ON/OFF (indication)
•Navigation guidance ON/OFF
•Reset settings (reset)
NOTE
•The desired driving position (display position, brightness level, display information) can
be called up after programming the position.
Refer to Driving Position Memory on page 2-7.
When Driving
Instrument Cluster and Display
4-41
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Glow Indicator Light
(SKYACTIV-D 2.2)
When the ignition is switched ON, the
glow indicator light turns on. The glow
indicator light turns
off when preheating is
finished.

A problem in the system might be
indicated under the following conditions.
Have your vehicle inspected by an expert
repairer, we recommend an Authorised
Mazda Repairer.
•The glow indicator light does not turn
on when the ignition is switched ON or
it remains on.
•The glow indicator light is flashing.
NOTE
If the vehicle is left with the ignition
switched ON without starting the engine
and a long period of time has elapsed
since preheating finished, the preheating
may be performed again and the glow
indicator light may turn on.
▼ Wrench Indication/Indicator Light
Type A instrument cluster
Perform maintenance in accordance with
the message.
Type B instrument cluster
When the ignition is switched ON, the
wrench indicator ligh
t is illuminated and
then turns off afte r a few seconds.
When illuminated
The wrench indicator light turns on under
the following conditions:
•When the preset maintenance period has
arrived.
•When it’s time to replace the engine oil.
Refer to Maintenance Monitor on page 6-
17.
When flashing (SKYACTIV-D 2.2)
The sedimentor separates water from the
fuel.
If water accumulates in this filter, the
warning light will flash. When it does,
consult an expert repairer, we recommend
an Authorised Mazda Repairer as soon as
possible.
▼ Low Engine Coolant Temperature
Indicator Light (Blue)*
The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.

When Driving
Instrument Cluster and Display
4-50*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Fuel Economy Monitor*
For vehicles with type B audio, the Control Status, Fuel Consumption, and Effectiveness*1
are switched and displayed by operating each icon in the display.
In addition, after completing a trip, the total energy efficiency to date is displayed in the
ending display when the ending display is turned on.
1. Select the
icon on the home screen to display the applications screen.
2. Select the “Fuel Economy Monitor”.
3. Select the
icon at the bot tom left of the screen t o display the menu in t he lower part
of the screen.
4. Select the icon in the menu and perform the operation. Each i con operates as follows:
Indication on displayControl status
Hides the menu display.
Displays the application screen.
Switches the Fuel Economy Monitor in the order of
Control Status, Fuel Consumption, and Effective-
ness
*1.
Resets the fuel economy data.
Displays the following setting screen.
•Ending display on/off switching•On/off switching for function which synchronizes re-
set fuel economy data to trip meter (Trip A) (Type B
instrument cluster only)
*1 With i-stop function.
NOTE
The fuel economy monitor screen after the ignition is switched from ON to OFF is changed
to the original fuel economy monitor screen when the ignition is switched ON the next time.
When Driving
Fuel Economy Monitor
4-96*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Fuel Consumption Display
Information regarding the fuel economy is displayed.
Indication on display
Control status
Displays the fuel economy for the past 60 minutes.
•Displays the fuel economy every minute for the past 1
to 10 minutes.
•Displays the fuel economy every 10 minutes for the
past 10 to 60 minutes.
Displays the average fuel economy over the past 5
resets and after the current reset.
Calculates the average fu el economy every minute
after vehicle travel b egins, and displays it.
NOTE
•The fuel economy data can be reset by doing the following operation:
•Press the reset switch from the menu screen.
•When the function which synchronizes the fu el economy monitor and the trip meter is
on, reset trip A of the trip meter.
•Delete the average fuel economy information displayed in the trip computer.
•After resetting the fuel economy data, “-- -” is displayed while the average fuel economy
is calculated.
▼ Control Status Display
(With i-stop Function)
The i-stop operation status and the i-ELOOP power generating st atus are displayed.
Indication on displayControl status
With i-ELOOP system
Displays the level of electricity generated by regen-
erative braking.
Displays the amount of the electricity stored in the
rechargeable battery.
When Driving
Fuel Economy Monitor
4-97
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•The vehicle speed is about 65 to 140 km/h (41 to 86 mph).
•The system detects white (yellow) lane lines.
•The system has completed learning of the driver’s driving data.
•The DAA does not operate under the following conditions.
•The vehicle speed is less than about 65 km/h (41 mph).
•The vehicle speed exceeds about 140 km/h (86 mph)
•The vehicle is making a sharp turn.
•The vehicle is changing lanes.
•The DAA may not operate normally under the following conditions.
•White (yellow) lane lines are less visible because of dirt or fading/patchiness.
•The vehicle is jolted or swayed continuously by strong winds or rough roads.
•The vehicle is driven aggressively.
•When making frequent lane changes.
•The DAA detects driver fatigue and decrease d attentiveness based on the driving data
when the vehicle is driven at about 65 to 140 km/h (41 to 86 mph) for about 20 minutes.
The driving data will be reset under the following conditions.
•The vehicle is stopped for 15 minutes or longer.
•The vehicle is driven at less than about 65 km/h (41 mph) for about 30 minutes.
•The ignition is switched off.
•After the DAA has displayed the first message encouraging rest, it does not display the
next one until 45 minutes have passed.
▼ Driver Attention Alert (DAA)
Display
When the system detects driver fatigue or
decreased attentiveness, it activates the
warning sound and displays an alert in the
multi-information display.
▼ Cancelling Driver
Attention Alert
(DAA)
The DAA can be set to not activate.
Refer to Personalisation Features on page
9-12.
When Driving
i-ACTIVSENSE
4-132
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Mazda Radar Cruise Control (MRCC) (Manual Transaxleand Taiwan)
*
The MRCC system is designed to maintain headway control*1 with a vehicle ahead
according to your vehic le's speed using a radar sensor (front) to detect the distance to the
vehicle ahead and a preset vehicle speed without you having to use the accelerator or brake
pedals.
*1 Headway Control: Control of the distance between your vehicle and the vehicle ahead
detected by the MRCC system.
Additionally, if your vehicle s tarts closing in on the vehicle ahead such as if the vehicle
ahead brakes suddenly, a warning sound and a warning indication in the display are
activated simultaneously to alert you to maintain a sufficient distance between the vehicles.
Also refer to the following before using the MRCC.
•Radar sensor (front) (page 4-201)
WA R N I N G
Do not rely completely on the MRCC:
The MRCC system has detection limitations depe nding on the type of vehicle ahead and its
conditions, the weather conditions, and the road conditions. Additionally, the system may be
unable to decelerate sufficiently to avoid hittin g the vehicle ahead if the vehicle ahead applies
the brakes suddenly or another vehicle cuts into the driving lane, which could result in an
accident.
Always drive carefully and verify the surrounding conditions and depress the brake pedal or
accelerator pedal while keeping a safer distance from vehicles ahead or on-coming vehicles.
Do not use the MRCC system in the following locations, using the MRCC system at the
following locations may result in an unexpected accident:
 General roads other than highways (Driving under these conditions using the MRCC system
is not possible.)
 Roads with sharp curves and where vehicle tr affic is heavy and there is insufficient space
between vehicles.
 Roads where frequent and repetitive accelerati on and deceleration occur (Driving under
these conditions using the MRCC system is not possible).
 When entering and exiting interchanges, servic e areas, and parking areas of highways (If
you exit a highway while headway control is in use, the vehicle ahead will no longer be
tracked and your vehicle may a ccelerate to the set speed).
 Slippery roads such as ice or snow-bound roads (Tyres could spin causing you to lose
vehicle control, or the stop hold control may not operate.)
When Driving
i-ACTIVSENSE
*Some models.4-137
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

The set speed can be adjusted
incrementally (1 km/h (1 mph)
increments) by pressing the switch and
releasing it immediately. For example, if
the switch is press ed 4 times, the set
vehicle speed decreases by about 4 km/h
(4 mph).
Cancelling the function
Cancelling using OFF/CAN switch
When the OFF/CAN switch is pressed
once, the cruise control function is
cancelled.
Cancelling using MODE switch
When the MODE switch is pressed, the
cruise control function is cancelled and the
headway control function is made
available for operation.
The cruise control fu nction is cancelled
automatically in the following cases. If the
RES switch is pressed while the vehicle
speed is 25 km/h (16 mph) or higher, the
speed returns to the original set speed.
•The OFF/CAN switch is pressed once.
•The brake pedal is depressed.
•The parking brake is applied.
(Manual transaxle)
•The clutch pedal is depressed.
•The shift lever is shifted to neutral
position.
(Automatic transaxle)
•The selector lever is shifted to P or N
position.
NOTE
•If the vehicle speed decreases by about
15 km/h (9.4 mph) or more than the set
speed, the cruise control function may
be cancelled.
•When the vehicle speed is less than 21
km/h (13 mph), the cruise control
function is cancelled. In this case, the
vehicle speed will not return to the
original set speed even if the vehicle is
accelerated to 25 km/h (16 mph) or
higher and the RES switch is pressed.
Reset the cruise control function.
When Driving
i-ACTIVSENSE
4-148
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Mazda Radar Cruise Control with Stop & Go function
(MRCC with Stop & Go functi on) (Automatic Transaxle
except Taiwan)
*
The MRCC with Stop & Go function system is designed to maintain headway control*1
with a vehicle ahead according to your vehicle's speed using a radar sensor (front) to detect
the distance to the vehicle ahead and a preset vehicle speed without you having to use the
accelerator or brake pedals.
*1 Headway Control: Control of the distance between your vehicle and the vehicle ahead
detected by the Mazda Radar Cr uise Control (MRCC) system.
Additionally, if your vehicle s tarts closing in on the vehicle ahead such as if the vehicle
ahead brakes suddenly, a warning sound and a warning indication in the display are
activated simultaneously to alert you to maintain a sufficient distance between the vehicles.
If the vehicle ahead stops while you are following behind it, your vehicle will stop and be
held stopped automatically (stop hold control), and headway con trol will resume when you
resume driving the vehicle such a s by pressing the RES switch.
Also refer to the following before using the MRCC with Stop & G o function.
•i-stop (page 4-12)
•AUTOHOLD (page 4-84)
•Forward Sensing Camera (FSC) (page 4-196)
•Radar sensor (front) (page 4-201)
WA R N I N G
Do not rely completely on the MRCC with Stop & Go function:
The MRCC with Stop & Go function system has detection limitations depending on the type of
vehicle ahead and its conditions, the weat her conditions, and the road conditions.
Additionally, the system may be unable to decelerate sufficiently to avoid hitting the vehicle
ahead if the vehicle ahead applies the brakes sudd enly or another vehicle cuts into the driving
lane, which could result in an accident.
Always drive carefully and verify the surrounding conditions and depress the brake pedal or
accelerator pedal while keeping a safer distance from vehicles ahead or on-coming vehicles.
Do not use the MRCC with Stop & Go function system in the following locations, using the
MRCC with Stop & Go function system at the following locations may result in an unexpected
accident:
 General roads other than highways (Driving under these conditions using the MRCC with
Stop & Go function system is not possible.)
When Driving
i-ACTIVSENSE
*Some models.4-149
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2