cooling MAZDA MODEL CX-5 2017 Owners Manual (in English)

3–32
Before Driving
Fuel and Emission
Engine Exhaust (Carbon monoxide)
WARNING
Do not drive your vehicle if you smell exhaust gas inside the vehicle: Engine exhaust gas is dangerous. This gas contains carbon monoxide (CO), which is
colorless, odorless, and poisonous. When inhaled, it can cause loss of consciousness and
death. If you smell exhaust gas inside the vehicle, keep all windows fully open and contact
an Authorized Mazda Dealer immediately.

Do not run the engine when inside an enclosed area: Running the engine inside an enclosed area, such as a garage, is dangerous. Exhaust
gas, which contains poisonous carbon monoxide, could easily enter the cabin. Loss of
consciousness or even death could occur.

Open the windows or adjust the heating or cooling system to draw fresh air when
idling the engine: Exhaust gas is dangerous. When the vehicle is stopped with the windows closed and
the engine running for a long time even in an open area, exhaust gas, which contains
poisonous carbon monoxide, could enter the cabin. Loss of consciousness or even death
could occur.

Clear snow from underneath and around your v ehicle, particularly the tail pipe, before
starting the engine: Running the engine when a vehicle is stopped in deep snow is dangerous. The exhaust
pipe could be blocked by the snow, allowing exhaust gas to enter the cabin. Because
exhaust gas contains poisonous carbon monoxide, it could cause loss of consciousness or
even death to occupants in the cabin.

CX-5_8FN1-EA-16L_Edition1.indb 322016/12/12 10:05:33

3–61
Before Driving
Towing
Trailer Towing Tips
  Verify that your Mazda maintains a near-normal attitude when a loaded or unloaded trailer
is connected. Do not drive if it has an abnormal front-up or front-down \
position. Inspect
for incorrect tongue load, worn suspension parts, and trailer overloadin\
g.
   Make sure the trailer is properly loaded and the cargo is secure to prevent it from shifting.  Make sure the mirrors conform to all government regulations. If they do \
not, install
required rear view mirrors appropriate for towing purposes.

The three main causes of vehicle-trailer accidents are driver error, excessive speed, and
improper trailer loading.
Before driving
   Have your cooling and braking system checked by an Authorized Mazda Dealer.  Before starting out, inspect the operation of all vehicle and trailer li\
ghts and all vehicle-
to-trailer connections. Stop and re-inspect all lights and connections a\
fter driving a short
distance.

Driving
   Your Mazda will handle differently with a trailer in tow, so practice turning, backing, and
stopping in a traf fi c-free area.
   Take time to get accustomed to the extra weight and length.  Allow more room between your vehicle and the one in front because brakin\
g distance
increases with a trailer. For each 16 km/h (10 mph) of speed, allow at least one vehicle
and trailer length between your Mazda and the vehicle ahead.
   Avoid jerky starts or sudden acceleration.  Avoid sudden braking. It may cause loss of control and result in jackkni fi ng, especially so
on wet or slippery roads.
   Shift the shift lever to the D position when towing a trailer in hilly t\
errain or when heavily
loaded.

The D position will allow operating the vehicle without frequent shiftin\
g.
Lane changes and turning
Avoid quick lane changes, sudden turns, and tight turns. Slow down before\
turning to avoid
the need of sudden braking.
A turning trailer will make a tighter arc than the tow vehicle. Compensat\
e with turns that are
larger than normal.
CX-5_8FN1-EA-16L_Edition1.indb 612016/12/12 10:05:39

4–11
When Driving
Start/Stop Engine
NOTE
  The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
  If the system detects that the remaining
battery power of the key is low when the
ignition is switched from ON to ACC or
OFF, the following is indicated.
 Replace with a new battery before the key becomes unusable.
 Refer to Key Battery Replacement on page 6-36 .
 (Vehicle equipped with Type A
instrument cluster)
 A message is indicated in the display of
the instrument cluster.
 (Vehicle equipped with Type B
instrument cluster)
 The KEY indicator light (green) fl ashes
for approximately 30 seconds.
 Refer to Warning/Indicator Lights on page 4-32 .
  (Automatic transaxle)  If the engine is turned off while the
selector lever is in a position other than
P, the ignition switches to ACC.

Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engine is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
CX-5_8FN1-EA-16L_Edition1.indb 112016/12/12 10:05:41

5–4
Interior Features
Climate Control System
Operating Tips
  Operate the climate control system with
the engine running.
   To prevent the battery from being
discharged, do not leave the fan control
dial/switch on for a long period of time
with the ignition switched ON when the
engine is not running.
   Clear all obstructions such as leaves,
snow and ice from the hood and the air
inlet in the cowl grille to improve the
system effi ciency.
  Use the climate control system to defog
the windows and dehumidify the air.
   The recirculate mode should be used
when driving through tunnels or while in
a traffi c jam, or when you would like to
shut off outside air for quick cooling of
the interior.
   Use the outside air position for
ventilation or windshield defrosting.
   If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then
run the climate control system.

   Run the air conditioner about 10 minutes
at least once a month to keep internal
parts lubricated.
   Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
effi cient.
 The refrigerant speci fi cations are
indicated on a label attached to the
inside of the engine compartment. Check
the label before re fi lling the refrigerant.
If the wrong type of refrigerant is used,
it could result in a serious malfunction
of the air conditioner.
 For details, consult an Authorized Mazda Dealer.

Type A

Label

Type B

Label

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:06:22

5–8
Interior Features
Climate Control System
Air intake selector
This switch controls the source of air
entering the vehicle.

Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (indicator light
illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traffi c (high engine exhaust
areas) or when quick cooling is desired.
Outside air position (indicator light
turned off)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windshield defrosting.
WARNING
Do not use the position in cold or
rainy weather: Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.

Rear window defogger switch
Press the rear window defogger switch to
defrost the rear window.
Refer to Rear Window Defogger on page
4-62 .
Heating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the outside air position (indicator light turns off).
3. Set the temperature control dial to the hot position.
4. Set the fan control dial to the desired speed.
5. If dehumidifi ed heating is desired, turn
on the air conditioner.

NOTE
   If the windshield fogs up easily, set the
mode selector dial to the
position.  If cooler air is desired at face level, set
the mode selector dial at the
position
and adjust the temperature control dial
to maintain maximum comfort.
   The air to the fl oor is warmer than air
to the face (except when the temperature
control dial is set at the extreme hot or
cold position).

Cooling
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the cold position.
3. Set the fan control dial to the desired speed.
4. Turn on the air conditioner by pressing the A/C switch.
5. After cooling begins, adjust the fan control dial and temperature control
dial as needed to maintain maximum
comfort.

CX-5_8FN1-EA-16L_Edition1.indb 82016/12/12 10:06:23

5–9
Interior Features
Climate Control System
CAUTION
If the air conditioner is used while
driving up long hills or in heavy traffi c,
monitor the high engine coolant
temperature warning indication/
warning light to see if it is illuminated
or fl ashing (page 4-32 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or fl ashing, turn the air-
conditioning off (page 7-18 ).

NOTE
  When maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then turn the fan control dial
fully clockwise.
  If warmer air is desired at fl oor level,
set the mode selector dial at the

position and adjust the temperature
control dial to maintain maximum
comfort.
   The air to the fl oor is warmer than air
to the face (except when the temperature
control dial is set at the extreme hot or
cold position).

Ventilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the outside air position (indicator light turns off).
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.

Windshield Defrosting and Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the desired position.
3. Set the fan control dial to the desired speed.
4. If dehumidifi ed heating is desired, turn
on the air conditioner.

WARNING
Do not defog the windshield using the

position with the temperature
control set to the cold position: Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windshield to fog up.
Your vision will be hampered, which
could lead to a serious accident. Set
the temperature control to the hot or
warm position when using the

position.

NOTE
   For maximum defrosting, turn on the air
conditioner, set the temperature control
dial to the extreme hot position, and
turn the fan control dial fully clockwise.
  If warm air is desired at the fl oor, set the
mode selector dial to the
position.   In the or position, the air
conditioner is automatically turned on
and the outside air position is
automatically selected to defrost the
windshield. In the
or position, the
outside air position cannot be changed
to the recirculated air position.

CX-5_8FN1-EA-16L_Edition1.indb 92016/12/12 10:06:24

5–12
Interior Features
Climate Control System
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.
  When the DUAL switch is off: Turn the driver temperature control dial
to control the temperature throughout
the entire cabin.
  When the DUAL switch is on: Turn the driver or front passenger
temperature control dial to
independently control the temperature
on each side of the cabin.

NOTE
  The climate control system changes to
the individual operation mode ( DUAL
switch indicator light illuminated) by
turning the front passenger temperature
control dial even when the DUAL switch
is off, which allows individual control
of the set temperature for the driver and
front passenger.
  The temperature units for the
temperature setting display can be
changed in conjunction with the
temperature units for the outside
temperature display.
 (Type A instrument cluster) Refer to Outside Temperature Display on page 4-24 .
 (Type B instrument cluster) Refer to Outside Temperature Display on page 4-17 .

Fan control switch
The fan has seven speeds. The selected
speed will be displayed.
Mode selector switch
The desired air fl ow mode can be selected
(page 5-6 ).
NOTE
   With the air fl ow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and air
at a comparably lower temperature will
fl ow through the central, left and right
vents.
   To set the air vent to , press the
windshield defroster switch.
   In the or position, the air
conditioner is automatically turned on
and the outside air position is
automatically selected to defrost the
windshield. In the
or position, the
outside air position cannot be changed
to the recirculated air position.

A/C switch
Pressing the A/C switch while the AUTO
switch is turned on will turn off the air-
conditioning (cooling/dehumidifying
functions).
The on/off of the air-conditioning switches
each time the A/C switch is pressed.
NOTE
   The air conditioner operates when the
A/C switch is pressed while the air
conditioner is turned off.
  The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).

CX-5_8FN1-EA-16L_Edition1.indb 122016/12/12 10:06:25

5–13
Interior Features
Climate Control System
Air intake selector
Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (
)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traf fi c (high engine exhaust
areas) or when quick cooling is desired.
Outside air position (
)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windshield defrosting.
WARNING
Do not use the position in cold or
rainy weather: Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.

DUAL switch
Use the DUAL switch to change the
mode between the individual operation
(driver and passenger) and interconnection
(simultaneous) modes.
Individual operation mode (indicator
light illuminated)
The set temperature can be controlled
individually for the driver and front
passenger.
Interconnection mode (indicator light
turned off)
The set temperature for the driver
and front passenger is controlled
simultaneously.
Windshield defroster switch
Press the switch to defrost the windshield
and front door windows.
Refer to Windshield Defrosting and
Defogging on page 5-14 .
Rear window defogger switch
Press the rear window defogger switch to
defrost the rear window.
Refer to Rear Window Defogger on page
4-62 .
Operation of Automatic Air- conditioning
1. Press the AUTO switch. Selection
of the air fl ow mode, air intake
selector and amount of air fl ow will be
automatically controlled.
2. Use the temperature control dial to select a desired temperature.
Press the DUAL switch or turn the front passenger temperature control
dial to control the set temperature
individually for the driver and front
passenger.

To turn off the system, press the OFF
switch.
NOTE
  Setting the temperature to maximum
hot or cold will not provide the desired
temperature at a faster rate.
  When selecting heat, the system will
restrict airfl ow until it has warmed to
prevent cold air from blowing out of the
vents.

CX-5_8FN1-EA-16L_Edition1.indb 132016/12/12 10:06:25

6–6
Maintenance and Care
Scheduled Maintenance
Remarks:
*1 The engine oil and fi lter must be changed at least once a year or within 12,000 km (7,500 mi\
les) since last
engine oil and fi lter change. Reset the engine oil data whenever replacing the engine oil\
regardless of the
message/wrench indicator light display.
*2 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*3 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
*4 If this component has been submerged in water, the oil should be replaced.
*5 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.


Schedule 2
U.S.A. and Puerto Rico residents - Severe driving conditions maintenance interval
Maintenance Interval Number of months or kilometers (miles), whichever comes
fi rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Spark plugs Replace every 120,000 km (75,000 miles).
Air fi lter
*1 Replace when any equivalent timing of replacing engine oil.
(Max interval: 36 months or 60,000 km (37,500 miles))
Drive belts I I
Engine oil & fi lter Flexible
*2
Replace when wrench indicator light is ON. (Max interval: 12
months or 12,000 km (7,500 miles))
Fixed R R R R R R R R R R R R
Engine coolant
*3 Replace at
fi rst 192,000 km (120,000 miles) or 10 years;
after that, every 96,000 km (60,000 miles) or 5 years.
Engine coolant level I I I I I I I I I I I I
Fuel lines and hoses
*4 I I I
Hoses and tubes for emission
*4 I
Function of all lights I I I I I I I I I I I I
Brake lines, hoses and connections I I I
Brake and clutch fl uid level I I I I I I I I I I I I
Disc brakes I I I I I I
Tire (Rotation) Rotate when any equivalent timing of replacing engine oil.
(Max interval: 8,000 km (5,000 miles))
Tire in fl ation pressure and tire wear I I I I I I I I I I I I
Steering operation and linkages I I I
Front and rear suspension, ball joints and wheel
bearing axial play I
I I
Rear differential oil
*5
CX-5_8FN1-EA-16L_Edition1.indb 62016/12/12 10:07:05

6–7
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometers (miles), whichever comes
fi rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Transfer oil
*5
Driveshaft dust boots I I I
Bolts and nuts on chassis and body T T T
Exhaust system and heat shields Inspect every 72,000 km (45,000 miles) or 5 years.
All locks and hinges L L L L L L L L L L L L
Washer fl uid level I I I I I I I I I I I I
Emergency fl at tire repair kit (if installed)
*6 Inspect annually.
Cabin air fi lter Replace when any equivalent timing of replacing engine oil.
(Max interval:24 months or 48,000 km (30,000 miles))
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R: Replace
L: Lubricate
T: Tighten
Remarks:
*1 If the vehicle is operated in very dusty or sandy areas, clean and if ne\
cessary, replace the air fi lter more often
than the recommended intervals.
*2 Engine oil fl exible maintenance is available for U.S.A. and Puerto Rico residents who\
se vehicle is operated
mainly where none of the following conditions apply.
 Extended periods of idling or low-speed operation such as police car, taxi or driving school car
 Driving in dusty conditions If any do apply, follow fi xed maintenance.
The engine oil and fi lter must be changed at least once a year or within 12,000 km (7,500 mi\
les) since last
engine oil and fi lter change. Reset the engine oil data whenever replacing the engine oil\
regardless of the
message/wrench indicator light display.
*3 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*4 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
*5 If this component has been submerged in water, the oil should be replaced.
*6 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.




CX-5_8FN1-EA-16L_Edition1.indb 72016/12/12 10:07:05