warning MAZDA MODEL CX-5 2017 Owners Manual (in English)

4–130
When Driving
i-ACTIVSENSE
How to change the set vehicle speed
To accelerate/decelerate using the SET
switch
When you press the SET
switch, the
vehicle accelerates and when you press the
SET
switch, it decelerates.

Short press 1 km/h (1 mph)
Long press 10 km/h (5 mph)

NOTE
For example, the set vehicle speed is
changed by pressing the SET switch four
times as follows:
The vehicle speed accelerates or
decelerates by 4 km/h (4 mph).

To increase speed using accelerator
pedal
Depress the accelerator pedal and press
and release the SET
switch or SET
switch at the desired speed. If the switch is
not operated, the system returns to the set
speed after you release your foot from the
accelerator pedal.
CAUTION
The warnings and brake control do not
operate while the accelerator pedal is
depressed.

NOTE
   The setting speed can be changed by
operating the SET
switch or SET
switch during stop hold control.
   When accelerating using the SET
switch while in headway control, the set
vehicle speed can be adjusted but
acceleration is not possible. If there is
no longer a vehicle ahead, acceleration
continues until reaching the set vehicle
speed. For the set vehicle speed, check
the set vehicle speed indication in the
display.
   When depressing the accelerator pedal,
the inter-vehicle distance indication in
the display changes to the white-line
indication.

Canceling the system
When the following operations are
performed, the Mazda Radar Cruise
Control with Stop & Go function (MRCC
with Stop & Go function) system is
canceled, and the Mazda Radar Cruise
Control with Stop & Go function (MRCC
with Stop & Go function) set indicator
(green) switches to the Mazda Radar
Cruise Control with Stop & Go function
(MRCC with Stop & Go function) main
indicator (white) at the same time.
  The OFF/CAN switch is pressed.  The brake pedal is depressed.  The electric parking brake (EPB) is
applied.
   The selector lever is in the P (Park), N
(Neutral), or R (Reverse) position.
   Any of the doors is opened.  The driver's seat belt is unfastened.

CX-5_8FN1-EA-16L_Edition1.indb 1302016/12/12 10:06:12

4–133
When Driving
i-ACTIVSENSE
Resume driving information
If you do not resume driving within a few seconds after the vehicle ahea\
d starts moving,
the multi-information display vehicle-ahead indication fl ashes to urge the driver to resume
driving.
Cruise Control Function
While this function is operating, the
headway control operation is canceled and
only the cruise control function operates.
The vehicle speed can be set more than
about 25 km/h (16 mph).
Use the cruise control function on
expressways and other highways which do
not require a lot of repeated acceleration
and deceleration.
WARNING
Do not use the cruise control function in
the following locations: Otherwise, it could lead to an accident.
 Roads with sharp curves and where vehicle traffi c is heavy and there is
insuffi cient space between vehicles.
(Driving under these conditions
using the cruise control function is
not possible)
 Steep down slopes (Set speed may be exceeded because suffi cient
engine braking cannot be applied)
 Slippery roads such as ice or snow- bound roads (Tires could spin
causing you to lose vehicle control)

Always drive carefully: The warnings and brake control
will not operate after the headway
control function is canceled and the
system is switched to only the cruise
control function. Depress the brake
pedal to decelerate according to the
surrounding conditions while keeping
a safer distance from the vehicle ahead
and always driving carefully.

Switching to cruise control function
When the MODE switch is pressed while
the Mazda Radar Cruise Control with Stop
& Go function (MRCC with Stop & Go
function) system is turned on, the system
switches to the cruise control function.
When the system switches to the cruise
control function, the indicator and multi-
information display notify the driver as
follows:
  The Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop
& Go function) set indication (green)
or the Mazda Radar Cruise Control
with Stop & Go function (MRCC with
Stop & Go function) main indication
(white) is turned off, and the cruise main
indication (white) is turned on.
   A message is displayed in the multi-
information display.

WARNING
Always turn off the cruise control
function when it is not in use: Leaving the cruise control function
turned on when it is not in use
is dangerous as it could operate
unexpectedly, resulting in an accident.

How to set the speed
Adjust the system to the desired vehicle
speed using the accelerator pedal.
When the SET
or SET switch is
pressed, the cruise set indication (green) is
turned on and headway control begins.
CX-5_8FN1-EA-16L_Edition1.indb 1332016/12/12 10:06:13

4–135
When Driving
i-ACTIVSENSE
*Some models.
Lane-keep Assist System (LAS) & Lane Departure
Warning System (LDWS)
*
The Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) alerts the
driver that the vehicle may be deviating from its lane and it provides s\
teering assistance to
help the driver stay within the vehicle lanes.
The Forward Sensing Camera (FSC) detects the white lines (yellow line\
s) of the vehicle
lane in which the vehicle is traveling and if the system determines that\
the vehicle may
deviate from its lane, it operates the electric power steering to assist\
the driver's steering
operation. The system also alerts the driver by activating a lane departure warning\
sound,
vibrating the steering wheel, and indicating an alert in the display.
Refer to Forward Sensing Camera (FSC) on page 4-156 .
Forward Sensing
Camera (FSC)

CX-5_8FN1-EA-16L_Edition1.indb 1352016/12/12 10:06:13

4–136
When Driving
i-ACTIVSENSE
WARNING
Do not rely completely on the Lane-keep Assist System (LAS) & Lane Departure
Warning System (LDWS):
 The Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) is not an automatic driving system. In addition, the system is not designed to compensate for a
driver's lack of caution, and over-reliance on the system could lead to an accident.
 The detection ability of the Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) is limited. Always stay on course using the steering wheel and drive
with care.

Do not use the Lane-keep Assist System (LAS) & Lane Departure Warning System
(LDWS) in the following cases: The system may not operate adequately according to the actual driving conditions,
resulting in an accident.
 Driving on roads with tight curves. Driving under bad weather conditions (rain, fog, and snow). Slippery roads such as ice or snow-bound roads. Roads with heavy traffi c and insuffi cient distance between vehicles. Roads with no white (yellow) lane lines. Narrow roads resulting from road construction or lane closures. The vehicle is driven on a temporary lane or section with a closed lane resulting from road construction where there may be multiple white (yellow) lane lines or they are
interrupted.
 The tire pressures are not adjusted to the specifi ed pressure. Tires of a diff erent specifi ed size are used, such as an emergency spare tire.
CAUTION
Heed the following cautions so that the Lane-keep Assist System (LAS) & Lane Departure
Warning System (LDWS) can operate normally.
 Do not modify the suspensions. Always use wheels of the specifi ed type and size for the front and rear wheels. Consult an Authorized Mazda Dealer for tire replacement.

CX-5_8FN1-EA-16L_Edition1.indb 1362016/12/12 10:06:13

4–137
When Driving
i-ACTIVSENSE
NOTE
  When the turn signal lever is operated for a lane change, the Lane-keep \
Assist System
(LAS) & Lane Departure Warning System (LDWS) is automatically disabled. The
Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) becomes
operational again when the turn signal lever is returned and the system detects white
(yellow) lane lines while the vehicle is being driven normally within \
its vehicle lane.
  If the steering wheel, accelerator pedal, or brake pedal is operated abr\
uptly and the
vehicle moves close to a white (yellow) line, the system determines th\
at the driver is
making a lane change and the Lane-keep Assist System (LAS) & Lane Departure Warning
System (LDWS) operation is temporarily canceled. The Lane-keep Assist System (LAS)
& Lane Departure Warning System (LDWS) becomes operational again when the system
detects white (yellow) lane lines while the vehicle is being driven no\
rmally within its
vehicle lane.
  If the vehicle deviates from its lane repeatedly within a short period of time, the Lane-
keep Assist System (LAS) & Lane Departure Warning System (LDWS) may not operate.
  When white (yellow) lane lines are not detected, the Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS) does not operate.
CX-5_8FN1-EA-16L_Edition1.indb 1372016/12/12 10:06:14

4–138
When Driving
i-ACTIVSENSE
  Under the following conditions, the Lane-keep Assist System (LAS) & Lane Departure
Warning System (LDWS) may not be able to detect white (yellow) lane l\
ines correctly and
it may not operate normally.
  If an object placed on the dashboard is re fl ected in the windshield and picked up by the
camera.
   Heavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is tilted.
  The tire pressures are not adjusted to the speci fi ed pressure.   Tires other than conventional tires are equipped.  When the vehicle is driven on the guiding branch to or from the rest area or tollgate of
a highway.
  The white (yellow) lane lines are less visible because of dirt or fading/patchiness.  A vehicle in front of your vehicle is running near a white (yellow) lane line making \
it
less visible.
  A white (yellow) lane line is less visible because of bad weather (rai\
n, fog, or snow).  The vehicle is driven on a temporary lane or section with a closed lane \
resulting
from construction where there may be multiple white (yellow) lane lines or they are
interrupted.
  A misleading line is picked up on the road such as a temporary line for construction,
or because of shade, lingering snow, or grooves fi lled with water.
   The surrounding brightness suddenly changes such as when entering or exiting a
tunnel.
  The illumination of the headlights is weakened because of dirt or the op\
tical axis is
deviated.
  The windshield is dirty or foggy.  The windshield, camera is fogged (water droplets).  Back-light is re fl ected off the road surface.   The road surface is wet and shiny after rain, or there are puddles on the road.  The shade of a guardrail parallel to a white (yellow) lane line is cast on the road.  The width of the driving lane is narrow or wide.  Driving on roads with tight curves.  The road is excessively uneven.  The vehicle is shaken after hitting a road bump.  There are two or more adjacent white (yellow) lane lines.  There are various road markings or lane markings of various shapes near an
intersection.


CX-5_8FN1-EA-16L_Edition1.indb 1382016/12/12 10:06:14

4–139
When Driving
i-ACTIVSENSE
System Operation
Make sure that the Lane-keep Assist
System (LAS) & Lane Departure Warning
System (LDWS) OFF indicator light in
the instrument cluster is turned off. When
the Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
OFF indicator light is turned on, press the
switch and make sure that the indicator
light turns off.

The Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
indication (white) is displayed in the
multi-information display, and the system
goes on stand-by.

(White) Drive the vehicle in the center of the
vehicle lane while the system is on
standby. When all of the following
conditions are met, the Lane-keep Assist
System (LAS) & Lane Departure Warning
System (LDWS) indication (green) is
displayed in the multi-information display,
and the system becomes operational.

(Green)   The engine is running.  The vehicle speed is about 60 km/h
(37 mph) or faster.
   The system detects white (yellow) lane
lines on both the right and left sides.
   The driver is operating the steering
wheel.
   The driving lane is neither narrow nor
wide.


NOTE
The Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
indication is white when the system detects
only a white (yellow) line on either the
left or right, and the indication changes
to green when the system detects white
(yellow) lines on both the left and right
sides.

Detection only on either left or right Detects on both
left and right sides
(White) (Green)

CX-5_8FN1-EA-16L_Edition1.indb 1392016/12/12 10:06:14

4–14 0
When Driving
i-ACTIVSENSE
The Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
goes on stand-by status in the following
cases:
  The system cannot detect white (yellow)
lane lines.
   The vehicle speed is less than about
60 km/h (37 mph).
   The ABS/TCS is operating.  The TCS is turned off. (If the TCS is turned off while the
system is operational, a warning beep is
heard and the system goes on standby.)
  The vehicle is making a sharp curve.  The brake pedal is depressed.  The steering wheel is operated abruptly.  The width of a lane is excessively
narrow or wide.

NOTE
   The Lane-keep Assist System (LAS)
& Lane Departure Warning System
(LDWS) does not operate until the
system detects white (yellow) lane lines
on either the left or right.
  When the system detects a white
(yellow) lane line on one side only, the
system will not operate the steering
wheel operation assist and the warning
for the lane line on the side that is not
being detected. The steering wheel
operation assist and the warning is only
for a lane deviation on the side that is
being detected.
  If the driver takes his or her hands off
the steering wheel (not holding the
steering wheel), the warning sound is
activated and an alert is indicated in the
multi-information display or the active
driving display.


Active Driving Display Multi-information Display(Windshield Type)
(Auto Flip-up Type)
 If the steering wheel is held lightly, or depending on the road conditions,
the system may detect that you have
released the steering wheel (not holding
the steering wheel) even if you are
holding it, and display a message in the
multi-information display or the active
driving display.
  The timing at which the lane departure
warning is activated and the steering
wheel operation assist is performed
varies.
CX-5_8FN1-EA-16L_Edition1.indb 1402016/12/12 10:06:14

4–141
When Driving
i-ACTIVSENSE
  The following settings for the Lane-
keep Assist System (LAS) & Lane
Departure Warning System (LDWS) can
be changed. Refer to Personalization
Features on page 9-11 .
  Steering operation assist
operational/non-operational
  Cancel sensitivity (likelihood of
steering assist)


Vehicle lane line display
When the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) becomes operational while
on standby, the vehicle lane lines are
displayed in the multi-information display
and the active driving display. In the
vehicle lane lines display indicating the
operation status, the color of the vehicle
lane lines being detected changes to white.
(Stand-by status)

Multi-information Display
Active Driving Display

(Operational status)

Multi-information Display
Active Driving Display

Auto cancel
In the following cases, the Lane-keep
Assist System (LAS) & Lane Departure
Warning System (LDWS) is automatically
canceled, the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) warning indication (amber)
turns on, and an alert is displayed. When
the Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
become operational, the system turns back
on automatically.
  The temperature inside the camera is
high or low.
   The windshield around the camera is
foggy.
   The windshield around the camera is
blocked by an obstruction, causing poor
forward visibility.

Auto cancel of warning/steering assist
When the following operations are
performed, the Lane-keep Assist System
(LAS) & Lane Departure Warning System
(LDWS) determines that the driver intends
to make a lane change and the system
operation is canceled automatically. The
Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS)
resumes automatically after the operation.
   The steering wheel is operated abruptly.  The brake pedal is operated.  The accelerator pedal is operated. (To cancel the automatic sensitivity
cancel function, deselect “Cancel
sensitivity” in the personalization
features setting.)
  The turn signal lever is operated.  The vehicle crosses a lane line.
CX-5_8FN1-EA-16L_Edition1.indb 1412016/12/12 10:06:14

4–142
When Driving
i-ACTIVSENSE
NOTE
  After the operation, the Lane-keep
Assist System (LAS) & Lane Departure
Warning System (LDWS) operation may
not operate for a period of 5 seconds
at the most until the lane lines are
detected.
  Under the following conditions, the
Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS)
cancels the warning/steering assist
automatically.
  The driver takes his/her hands off the
steering wheel.
 (The Lane-keep Assist System (LAS) & Lane Departure Warning System
(LDWS) is designed to assist the
driver's steering operation and it
will resume operation automatically
when the driver holds the steering
wheel.)
  The TCS OFF switch is pressed to
cancel the TCS.


Steering operation assist OFF (non-
operational)
The steering operation assist for the
Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS) can
be changed to non-operational (OFF).
Refer to Setting Change (Personalization
Features) on page 9-11 .
When the steering operation assist has
been changed to non-operational (OFF),
the operation conditions and the display
of the Lane-keep Assist System (LAS) &
Lane Departure Warning System (LDWS)
differ. Operate the system as follows:
System operation
Make sure that the Lane-keep Assist
System (LAS) & Lane Departure Warning
System (LDWS) OFF indicator light in the
instrument cluster is turned off. When the
Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS) OFF
indicator light turns on, press the switch
and make sure that the indicator light turns
off.


CX-5_8FN1-EA-16L_Edition1.indb 1422016/12/12 10:06:15