change time MAZDA MODEL CX-5 2017 (in English) Workshop Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2017, Model line: MODEL CX-5, Model: MAZDA MODEL CX-5 2017Pages: 664, PDF Size: 11.73 MB
Page 468 of 664

5–14 0
Interior Features
Interior Equipment
NOTE
Once the rear map lights have been
turned off, they will turn on and off
depending on the position to which the
overhead light is switched.
The rear map lights will not turn
off even if the lens is pressed in the
following cases:
The overhead light switch is ON. The overhead light switch is in the
door position with the door open.
The illuminated entry system is on.
Luggage Compartment Lights
Switch
Position Luggage Compartment Light
Light off
Light on when the liftgate is open
Illuminated Entry System
When the illuminated entry system
operates, the overhead lights turn on in the
following conditions:
The driver's door is unlocked after the
ignition is switched OFF.
The ignition is switched OFF with all
doors closed.
NOTE
The illuminated entry system operates
when the overhead light switch is in the
DOOR position.
The illumination time differs depending
on the operation.
Battery saver If an interior light is left on with the
ignition switched OFF, the light is
turned off automatically after about
30 minutes to prevent battery depletion.
The operation of the illuminated entry
system can be changed.
Refer to Personalization Features on page 9-11 .
CX-5_8FN1-EA-16L_Edition1.indb 1402016/12/12 10:07:01
Page 482 of 664

6–6
Maintenance and Care
Scheduled Maintenance
Remarks:
*1 The engine oil and fi lter must be changed at least once a year or within 12,000 km (7,500 mi\
les) since last
engine oil and fi lter change. Reset the engine oil data whenever replacing the engine oil\
regardless of the
message/wrench indicator light display.
*2 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*3 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
*4 If this component has been submerged in water, the oil should be replaced.
*5 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.
Schedule 2
U.S.A. and Puerto Rico residents - Severe driving conditions maintenance interval
Maintenance Interval Number of months or kilometers (miles), whichever comes
fi rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Spark plugs Replace every 120,000 km (75,000 miles).
Air fi lter
*1 Replace when any equivalent timing of replacing engine oil.
(Max interval: 36 months or 60,000 km (37,500 miles))
Drive belts I I
Engine oil & fi lter Flexible
*2
Replace when wrench indicator light is ON. (Max interval: 12
months or 12,000 km (7,500 miles))
Fixed R R R R R R R R R R R R
Engine coolant
*3 Replace at
fi rst 192,000 km (120,000 miles) or 10 years;
after that, every 96,000 km (60,000 miles) or 5 years.
Engine coolant level I I I I I I I I I I I I
Fuel lines and hoses
*4 I I I
Hoses and tubes for emission
*4 I
Function of all lights I I I I I I I I I I I I
Brake lines, hoses and connections I I I
Brake and clutch fl uid level I I I I I I I I I I I I
Disc brakes I I I I I I
Tire (Rotation) Rotate when any equivalent timing of replacing engine oil.
(Max interval: 8,000 km (5,000 miles))
Tire in fl ation pressure and tire wear I I I I I I I I I I I I
Steering operation and linkages I I I
Front and rear suspension, ball joints and wheel
bearing axial play I
I I
Rear differential oil
*5
CX-5_8FN1-EA-16L_Edition1.indb 62016/12/12 10:07:05
Page 483 of 664

6–7
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometers (miles), whichever comes
fi rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Transfer oil
*5
Driveshaft dust boots I I I
Bolts and nuts on chassis and body T T T
Exhaust system and heat shields Inspect every 72,000 km (45,000 miles) or 5 years.
All locks and hinges L L L L L L L L L L L L
Washer fl uid level I I I I I I I I I I I I
Emergency fl at tire repair kit (if installed)
*6 Inspect annually.
Cabin air fi lter Replace when any equivalent timing of replacing engine oil.
(Max interval:24 months or 48,000 km (30,000 miles))
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R: Replace
L: Lubricate
T: Tighten
Remarks:
*1 If the vehicle is operated in very dusty or sandy areas, clean and if ne\
cessary, replace the air fi lter more often
than the recommended intervals.
*2 Engine oil fl exible maintenance is available for U.S.A. and Puerto Rico residents who\
se vehicle is operated
mainly where none of the following conditions apply.
Extended periods of idling or low-speed operation such as police car, taxi or driving school car
Driving in dusty conditions If any do apply, follow fi xed maintenance.
The engine oil and fi lter must be changed at least once a year or within 12,000 km (7,500 mi\
les) since last
engine oil and fi lter change. Reset the engine oil data whenever replacing the engine oil\
regardless of the
message/wrench indicator light display.
*3 Use of FL-22 is recommended when replacing engine coolant. Using engine \
coolant other than FL-22 may cause serious damage to the engine and cooling system.
*4 According to state/provincial and federal regulations, failure to perfor\
m maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage/kilometer period to ensure long-term reliabi\
lity.
*5 If this component has been submerged in water, the oil should be replaced.
*6 Check the tire repair fl uid expiration date every year when performing the periodic maintenance.\
Replace the
tire repair fl uid bottle with new one before the expiration date.
CX-5_8FN1-EA-16L_Edition1.indb 72016/12/12 10:07:05
Page 493 of 664

6–17
Maintenance and Care
Scheduled Maintenance
You can customize settings in the setup display as follows:
Tab Item Explanation
Scheduled Setting
Notifi cation can be switched on/off.
Time (months) Displays the time or distance until maintenance is due.
Select this item to set the maintenance period.
The wrench indication/indicator light in the instrument cluster will
be illuminated when the remaining distance is less than
1,000 km or 600 mile, or the remaining number of days is less than
15 (whichever comes
fi rst).
Distance (km or mile)
Reset Resets the time and distance to the initial values.
Once the system turns on, it needs to be reset whenever carrying
out maintenance.
Tire Rotation Setting
Notifi cation can be switched on/off.
Distance (km or mile) Displays the distance until tire rotation is due.
Select this item to set the tire rotation distance.
The wrench indication/indicator light in the instrument cluster will
be illuminated when the remaining distance is less than 1,000 km
or 600 mile.
Reset Resets the remaining distance to the initial value.
Once the system turns on, it needs to be reset whenever rotating
the tires.
Oil Change Setting Interval
Oil replacement period can be selected from the
fl exible setting or
fi xed setting, or it can be set to non-display.
The fl exible setting is available only in the United States and
Puerto Rico. Once engine oil fl exible maintenance is selected,
the vehicle calculates the remaining oil life based on the engine
operating conditions. The vehicle lets you know when an oil
change is due by illuminating the wrench indicator light in the
instrument cluster. Mazda Genuine 0W-20 oil and Castrol
® 0W-20
oil are required to achieve optimum performance.
Distance (km or mile)
(Displays only in fi xed
setting) Displays the distance until the oil replacement is due.
Select this item to set the oil replacement distance.
The wrench indication/indicator light in the instrument cluster will
be illuminated when the remaining distance is less than 1,000 km
or 600 mile.
Oil life (km or mile)
(Displays only in fl exible
setting) Displays the engine oil life until the oil replacement is due.
The wrench indication/indicator light in the instrument cluster will
be illuminated when the remaining oil life distance is less than
1,000 km or 600 mile.
Reset In
fl exible setting: Resets the remaining oil life to 100 %.
In fi xed setting: Resets the remaining distance to the initial value.
Once the Flexible Oil Maintenance Setting is selected, the system
must be reset whenever replacing the engine oil.
CX-5_8FN1-EA-16L_Edition1.indb 172016/12/12 10:07:06
Page 504 of 664

6–28
Maintenance and Care
Owner Maintenance
Inspect fl uid level in the washer fl uid
reservoir; add fl uid if necessary.
L F
OK
The top of the fl oat should be between F
and L.
Use plain water if washer fl uid is
unavailable.
But use only washer fl uid in cold weather
to prevent it from freezing.
NOTE
Front and rear washer fl uid is supplied
from the same reservoir.
Body Lubrication
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
CX-5_8FN1-EA-16L_Edition1.indb 282016/12/12 10:07:09
Page 581 of 664

7–39
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Warning Sound is
Activated
Lights-On Reminder
The lights-on reminder is operable when
the time setting *1 of the auto headlight off
function is off.
If lights are on and the ignition is switched
to ACC or off, a continuous beep sound
will be heard when the driver's door is
opened.
*1 If the light switch is left on, the auto headlight off function automatically
turns off the lights about 30 seconds
after switching the ignition off. The
time setting can be changed.
Refer to Personalization Features on page 9-11 .
NOTE
When the ignition is switched to ACC,
the “Ignition Not Switched Off (STOP)
Warning Beep” (page 7-40 ) overrides
the lights-on reminder.
A personalized function is available to
change the sound volume for the lights-
on reminder.
Refer to Personalization Features on page 9-11 .
Air Bag/Seat Belt Pretensioner System Warning Beep
If there is a problem with the air bag/seat
belt pretensioner systems and the warning
light illumination, a warning beep sound
will be heard for about 5 seconds every
minute.
The air bag and seat belt pretensioner
system warning beep sound will continue
to be heard for approximately
35 minutes. Have your vehicle inspected
at an Authorized Mazda Dealer as soon as
possible.
WARNING
Do not drive the vehicle with the air
bag/seat belt pretensioner system
warning beep sounding:
Driving the vehicle with the air bag/
seat belt pretensioner system warning
beep sounding is dangerous. In a
collision, the air bags and the seat belt
pretensioner system will not deploy
and this could result in death or serious
injury. Contact an Authorized Mazda
Dealer to have the vehicle inspected as
soon as possible.
CX-5_8FN1-EA-16L_Edition1.indb 392016/12/12 10:07:29
Page 584 of 664

7–42
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Power Liftgate Warning Beep *
If system operation precautions are
necessary, the driver is notifi ed by the
warning sound.
Cautions What to check
The beep sounds 3 times The conditions required
for the power liftgate
to operate have not
been met, such as an
object being stuck in the
liftgate.
The beep sound
continues The vehicle is being
driven with the liftgate
open. Stop the vehicle
and close the liftgate.
Electric Parking Brake (EPB)
Warning Beep
The warning buzzer is activated under the
following conditions:
The vehicle is driven with the electric
parking brake (EPB) applied.
The electric parking brake (EPB) switch
is pulled while the vehicle is driven.
AUTOHOLD Warning Beep
Warning light fl ashes/message is
displayed and beep sound is activated
simultaneously for about fi ve seconds
when using AUTOHOLD function or
when AUTOHOLD switch is operated.
Because a problem with AUTOHOLD
function has occurred, AUTOHOLD
function does not operate even if
AUTOHOLD switch is operated.
If the warning light fl ashes/message is
displayed and the beep sound is activated
simultaneously, have your vehicle
inspected at an Authorized Mazda Dealer.
Power Steering Warning Buzzer
If the power steering system has
a malfunction, the power steering
malfunction light turns on or fl ashes and
the buzzer operates at the same time.
Refer to Warning Indication/Warning
Lights on page 4-33 .
Tire Infl ation Pressure Warning
Beep *
The warning beep sound will be heard
for about 3 seconds if the tire pressures
decrease.
If the tire pressure decreases extremely,
a beep sound will be heard for
approximately 30 seconds.
Refer to Tire Pressure Monitoring System
on page 4-172 .
Blind Spot Monitoring (BSM) Warning Beep *
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the Blind Spot Monitoring (BSM) warning
light is illuminated.
NOTE
A personalized function is available to
change the Blind Spot Monitoring (BSM)
warning beep sound volume.
Refer to Personalization Features on page
9-11 .
Reversing
If a moving object such as a vehicle or
two-wheeled vehicle approaches on the
left or right from behind your vehicle, the
Blind Spot Monitoring (BSM) warning
sound is activated.
CX-5_8FN1-EA-16L_Edition1.indb 422016/12/12 10:07:29
Page 585 of 664

7–43
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Lane Departure Warning Sound *
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a warning
sound.
NOTE
The volume of the Lane-keep Assist
System (LAS) & Lane Departure
Warning System (LDWS) warning sound
can be changed.
Refer to Personalization Features on page 9-11 .
The type of the Lane-keep Assist System
(LAS) & Lane Departure Warning
System (LDWS) warning sound can be
changed.
Refer to Personalization Features on page 9-11 .
Collision warning *
If there is a possibility of a collision with
a vehicle ahead or an obstruction at the
rear of the vehicle, the warning light in the
instrument cluster fl ashes at the same time
as the warning indication is displayed in
the multi-information display or the active
driving display, and a warning sound is
activated intermittently.
Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) System
Warnings
*
The Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop &
Go function) system warnings notify the
driver of system problems and precautions
on use when required. Check after hearing
a warning beep sound.
Warning beep What to check
While the Mazda Radar
Cruise Control with
Stop & Go function
(MRCC with Stop &
Go function) system is
operating, a single beep
sound is heard when
“Front radar blocked” is
displayed in the multi-
information display. Cancel the Mazda Radar
Cruise Control with
Stop & Go function
(MRCC with Stop &
Go function) system if
the radar sensor (front)
becomes dirty. Clean the
area around the radar
sensor (front).
The beep sounds
intermittently while the
vehicle is being driven. The distance between
your vehicle and the
vehicle ahead is too
close. Verify the safety
of the surrounding area
and reduce vehicle
speed.
While the Mazda Radar
Cruise Control with
Stop & Go function
(MRCC with Stop &
Go function) system is
operating, a single beep
sound is heard when
“Front radar sensor
system malfunction” is
displayed in the multi-
information display. A malfunction in the
system may be indicated.
Check the center display
to verify the problem
and then have your
vehicle inspected by
an Authorized Mazda
Dealer.
CX-5_8FN1-EA-16L_Edition1.indb 432016/12/12 10:07:29
Page 631 of 664

8–43
Customer Information and Reporting Safety Defects
Declaration of Conformity
NOTE
During printing time of this user manual the approvals listed above are granted.
WARNING
Change or modifi cations not expressively approved by the party responsible for
compliance could void the use's authority to operate the equipment.
HomeLink Wireless Control System
CAUTION
HomeLink has been tested and complies with FCC and Industry Canada rules. Changes or
modifi cations not expressly approved by the party responsible for compliance could void
the user's authority to operate the device.
NOTE
FCC ID: NZLMOBHL4
CANADA:4112A-MOBHL4
This device complies with part 15 of the FCC Rules. Operation is subject\
to the following
two conditions:
1- This device may not cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
Tire Pressure Monitoring System
NOTE
This device complies with part 15 of the FCC Rules. Operation is subject\
to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Bluetooth ® Hands-Free
Type A
U.S.A. and Canada
CX-5_8FN1-EA-16L_Edition1.indb 432016/12/12 10:07:36
Page 650 of 664

9–14
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings
Change
Method
Vehicle
Door locks (page
3-17 ) Operation condition of auto lock/unlock
function Lock:
Driving, Unlock:
IGN Off Off/
Lock When Driving/
Lock: Driving, Unlock: IGN Off/
Lock When
Shifting Out Of P/
Lock: Shift From P,
Unlock: In P/
Lock: Driving, Unlock: In P A D
Keyless entry
system (page
3-3 ) Method for unlocking door using transmitter
Once:
Driver's,
Twice: All Doors Touch Once:
All Doors/
Once: Driver's, Twice: All Doors A E
Time for locking door automatically 60 seconds 90 seconds/
60 seconds/
30 seconds A —
Advanced keyless
entry system (page
3-10 ) Method for unlocking door using request
switch/transmitter
Once:
Driver's,
Twice: All Doors Touch Once:
All Doors/
Once: Driver's, Twice: All Doors A
E,
F
Time for locking door automatically 60 seconds 90 seconds/
60 seconds/
30 seconds A —
Auto-lock function operation/non-operational Off On/Off A —
Beep volume when locking/unlocking Medium High/
Medium/ Low/ Off A
E,
F
Illuminated entry
system (page
5-140 ) Time until interior lights turn off after
closing door
15 seconds 60 seconds/
30 seconds/
15 seconds/
7.5 seconds A —
Time until interior lights turn off
automatically when any door is not closed
completely 30 minutes 60 minutes/
30 minutes/
10 minutes A —
Auto-wiper control
(page 4-58 ) Operational/non-operational
On On/Off
*4 A —
CX-5_8FN1-EA-16L_Edition1.indb 142016/12/12 10:07:40